Nissan Tiida C11. Manual — part 166
DLK-74
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR SWITCH
2.
Check continuity between BCM connector (A) M18 terminal 10
and back door lock assembly (door switch) connector (B) D405
terminal 3.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness between BCM and back door lock assembly.
3.
CHECK BACK DOOR LOCK ASSEMBLY GROUND CIRCUIT
Check continuity between back door lock assembly connector and
ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace back door lock assembly ground circuit.
4.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
ALKIA0756ZZ
BCM connector
Terminal
Back door lock assembly
(door switch) connector
Terminal
Continuity
M18
10
D405
3
Yes
BCM connector
Terminal
Ground
Continuity
M18
10
No
ALKIA0757ZZ
Back door lock assembly
(door switch) connector
Terminal
Ground
Continuity
D405
4
Yes
DOOR SWITCH
DLK-75
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
Check voltage between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 6.
5.
CHECK BACK DOOR LOCK ASSEMBLY (DOOR SWITCH)
Check back door lock assembly (door switch).
Refer to
DLK-75, "BACK DOOR : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace back door lock assembly (door switch). Refer to
XX-XX, "*****"
and
XX-XX, "*****"
.
6.
CHECK INTERMITTENT INCIDENT
Refer to @@@.
>> INSPECTION END
BACK DOOR : Component Inspection
INFOID:0000000001396555
1.
CHECK BACK DOOR LOCK ASSEMBLY (DOOR SWITCH)
1.
Turn ignition switch OFF.
2.
Check back door lock assembly (door switch).
Is the inspection result normal?
ALKIA0755ZZ
Terminals
Voltage (V)
(Approx.)
(+)
(–)
BCM connector
Terminal
M18
10
Ground
Battery voltage
ALKIA0758ZZ
Terminal
Back door condition
Continuity
Back door lock assembly (door switch)
3
4
OPEN
Yes
CLOSE
No
DLK-76
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR SWITCH
YES
>> Back door lock assembly (door switch) is OK.
NO
>> Replace back door lock assembly (door switch). Refer to
XX-XX, "*****"
and
XX-XX, "*****"
.
KEY SWITCH
DLK-77
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY SWITCH
Description
INFOID:0000000001396556
Key switch detects that mechanical key is inserted into the key cylinder, and then transmits the signal to Intel-
ligent Key unit.
Component Function Check
INFOID:0000000001396557
1.
CHECK KEY SWITCH INPUT SIGNAL
Check key switch (“KEY SW”) in “Data Monitor” mode with CONSULT-III. Refer to
CONSULT-III Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> Key switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000001396558
1.
CHECK KEY SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key unit connector.
3.
Check voltage between Intelligent Key unit harness connector
and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK KEY SWITCH POWER SUPPLY CIRCUIT
1.
Remove mechanical key from key cylinder.
2.
Disconnect key switch and ignition knob switch connector.
Monitor item
Condition
KEY SW
Insert mechanical key into key cylinder
: ON
Remove mechanical key from key cylinder
: OFF
WIIA1173E
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
Intelligent Key unit con-
nector
Terminal
M52
7
Ground
Insert mechanical key into key
cylinder
Battery voltage
Remove mechanical key from
key cylinder
0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст