Nissan Tiida C11. Manual — part 711
EM-196
< ON-VEHICLE REPAIR >
[MR18DE]
OIL SEAL
• Drive belt; Refer to
.
• Crankshaft pulley; Refer to
2.
Remove front oil seal using a suitable tool.
CAUTION:
Be careful not to damage front cover and crankshaft.
INSTALLATION
1.
Apply new engine oil to new front oil seal joint surface and seal lip.
2.
Install front oil seal so that each seal lip is oriented as shown in
the figure.
• Install front oil seal (2) using a suitable tool with outer diameter
57 mm (2.24 in) and inner diameter 45 mm (1.77 in) (A) to the
dimension as shown.
CAUTION:
• Be careful not to damage front cover and crankshaft.
• Press-fit oil seal straight to avoid causing burrs or tilt-
ing.
• Do not touch grease applied on oil seal lip.
3.
Installation of the remaining components is in the reverse order of removal.
Removal and Installation of Rear Oil Seal
INFOID:0000000001337802
REMOVAL
1.
Remove transaxle assembly. Refer to
TM-681, "Removal and Installation"
2.
Remove clutch cover and clutch disk. Refer to
CL-13, "Removal and Installation"
.
3.
Remove flywheel. Refer to
.
4.
Remove rear oil seal with a suitable tool.
CAUTION:
Be careful not to damage crankshaft and cylinder block.
INSTALLATION
1.
Apply the liquid gasket lightly to entire outside area of new rear oil seal.
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-27, "Recommended Chemical Prod-
.
A
: Dust seal lip
B
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
Within 0.3 mm (0.012 in) toward engine front
Within 0.5 mm (0.020 in) toward engine rear
PBIC3729E
OIL SEAL
EM-197
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Install rear oil seal so that each seal lip is oriented as shown.
• Install rear oil seal with a suitable tool with an outer diameter
115 mm (4.53 in) and inner diameter 90 mm (3.54 in) (A).
CAUTION:
• Be careful not to damage crankshaft and cylinder block.
• Press-fit oil seal straight to avoid causing burrs or tilt-
ing.
• Do not touch grease applied onto oil seal lip.
• Install rear oil seal (1) to the position as shown.
NOTE:
The standard surface of the dimension is the rear end surface of
cylinder block.
3.
Installation of the remaining components is in the reverse order of removal.
A
: Dust seal lip
B
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
PBIC3951E
A
: Rear end surface of cylinder block
PBIC3761E
EM-198
< ON-VEHICLE REPAIR >
[MR18DE]
CYLINDER HEAD
CYLINDER HEAD
Component
INFOID:0000000001337804
Removal and Installation
INFOID:0000000001337805
REMOVAL
WARNING:
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Do not smoke while servicing fuel system. Keep open flames and sparks away from the work area.
1.
Release the fuel pressure. Refer to
.
2.
Drain engine coolant and engine oil. Refer to
CO-35, "Changing Engine Coolant"
and
.
3.
Remove front fender protector (RH). Refer to
EXT-22, "Removal and Installation"
4.
Remove drive belt. Refer to
EM-142, "Removal and Installation"
5.
Remove the following components and related parts.
• Exhaust manifold; Refer to
.
• Intake manifold; Refer to
• Fuel tube and fuel injector assembly; Refer to
• Water outlet; Refer to
CO-47, "Removal and Installation"
• Rocker cover; Refer to
EM-173, "Removal and Installation"
• Front cover, timing chain; Refer to
• Camshaft; Refer to
6.
Remove cylinder head.
• Loosen bolts in reverse order as shown.
• Using TORX socket (size E18), loosen cylinder head bolts.
7.
Remove cylinder head gasket.
1.
Cylinder head assembly
2.
Cylinder head bolt
3.
Cylinder head gasket
A.
Refer to
PBIC3542J
: Engine front
PBIC3206J
CYLINDER HEAD
EM-199
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
INSPECTION AFTER REMOVAL
Cylinder Head Bolts Outer Diameter
• Cylinder head bolts are tightened by plastic zone tightening
method. Whenever the size difference between “d1” and “d2”
exceeds the limit, replace them with a new one.
• If reduction of outer diameter appears in a position other than “d2”,
use it as “d2” point.
Cylinder Head Distortion
NOTE:
When performing this inspection, cylinder block distortion should be also checked. Refer to
1.
Wipe off engine oil and remove water scale (like deposit), gasket, sealant, carbon, etc. with a scraper.
CAUTION:
Use utmost care not to allow gasket debris to enter passages for engine oil or water.
2.
At each of several locations on bottom surface of cylinder head,
measure the distortion in six directions using straightedge (A)
and feeler gauge (B).
• If it exceeds the limit, replace cylinder head.
INSTALLATION
1.
Install cylinder head gasket.
2.
Apply new engine oil to threads and seating surface of bolts.
CAUTION:
If cylinder head bolts re-used, check their outer diameters before installation. Follow the "Cylinder
Head Bolts Outer Diameter" measurement procedure.
3.
Install cylinder head, follow the steps below to tighten cylinder
head bolts in numerical order as shown.
Limit (“d1” – “d2”): 0.15 mm (0.0059 in)
PBIC3994E
Limit: 0.1 mm (0.004 in)
PBIC3207J
Step a
: 40 N·m (4.1 kg-m, 30 ft-lb)
Step b
: 100
°
clockwise
Step c
: Loosen to 0 N·m in the reverse order of tight-
ening.
Step d
: 40 N·m (4.1 kg-m, 30 ft-lb)
Step e
: 100
°
clockwise
Step f
: 100
°
clockwise
PBIC3206J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст