Nissan Tiida C11. Manual — part 1468
FRONT WASHER NOZZLE AND TUBE
WW-67
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WASHER NOZZLE AND TUBE
Washer Tube Layout
INFOID:0000000001396458
Removal and Installation
INFOID:0000000001404271
REMOVAL
1.
Remove the cowl top cover. Refer to
EXT-20, "Removal and Installation"
.
2.
Disconnect the washer tube from the front washer nozzle.
3.
While pressing pawl (A) on the reverse side of front washer noz-
zle (1), remove front washer nozzle (1) from cowl top cover.
INSTALLATION
1.
Attach the washer tube to the front washer nozzle.
2.
Install the front washer nozzle in the cowl top cover.
3.
Install the cowl top cover. Refer to
EXT-20, "Removal and Installation"
4.
Adjust the front washer nozzle spray pattern. Refer to
.
CAUTION:
The spray points are different from side to side, so install the left and right front washer nozzles in
the correct positions.
Inspection
INFOID:0000000001404272
CHECK VALVE INSPECTION
1.
Front washer nozzle (LH)
2.
Front washer nozzle (RH)
3.
Joint washer tube
4.
Washer tube
5.
Clip
6.
Clamp
7.
Washer tank
SKIB5664E
LKIA0939E
WW-68
< ON-VEHICLE REPAIR >
FRONT WASHER NOZZLE AND TUBE
Blow air in the injection direction, and make sure that air flows only
one way. Make sure that the reverse direction is not possible.
Adjustment
INFOID:0000000001404273
• Adjust spray positions to match the positions as shown.
• Insert a suitable tool into the nozzle hole and move up/down and left/right to adjust to the specified spray
position.
SKIB5665E
1.
Windshield
A.
395 mm (15.55 in)
B.
216 mm (8.50 in)
C.
100 mm (3.94 in)
D.
85 mm (3.35 in)
E.
Black mask
F.
303 mm (11.93 in)
G.
212 mm (8.35 in)
H.
249 mm (9.80 in)
I.
Center of windsheild
J.
Spray pattern area
K.
286 mm (11.26 in)
LKIA0938E
FRONT WIPER ARM
WW-69
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER ARM
Exploded View
INFOID:0000000001366661
LHD Models
LKIA0786E
1.
Front RH wiper blade
2.
Front RH wiper arm
3.
Wiper arm cap
4.
Front wiper drive assembly
5.
Front LH wiper arm
6.
Wiper arm cap
7.
Front LH wiper blade
WW-70
< ON-VEHICLE REPAIR >
FRONT WIPER ARM
RHD Models
Removal and Installation
INFOID:0000000001449632
REMOVAL
1.
Operate the front wiper to move it to the auto stop position.
2.
Open the hood.
3.
Remove the front wiper arm caps.
4.
Remove the front wiper arm nuts.
5.
Raise the front wiper arms, and remove the front wiper arms.
INSTALLATION
1.
Clean up the pivot area as shown. This will reduce possibility of
wiper arm looseness.
2.
Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it off (auto stop).
3.
Push wiper arm onto pivot shaft, make sure it is correctly
meshed and fully seated on the spline.
ALLIA0278ZZ
1.
Wiper arm cap
2.
Front RH wiper arm
3.
Wiper arm cap
4.
Front LH wiper arm
5.
Front wiper drive assembly
6.
Front LH wiper blade
7.
Front RH wiper blade
Front
SEL024J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст