Nissan Tiida C11. Manual — part 1370
REPAIR FOR COMPONENT PARTS
TM-531
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Pull out retaining pin (2) of parking rod plate (1) using suitable
tool.
4.
Pull out retaining pin (1) of manual shaft using suitable tool.
5.
Remove parking rod plate (with parking rod) (3) from manual
shaft (1).
6.
Remove parking rod from parking rod plate (3).
7.
Remove manual plate (2) from manual shaft (1).
8.
Draw out manual shaft (1) from transaxle case.
9.
Remove manual shaft oil seal from transaxle case using suitable
tool.
CAUTION:
Do not scratch transaxle case.
INSPECTION
Check component parts, and replace if damaged or worn.
INSTALLATION
SCIA5806J
SCIA6514J
SCIA7005E
SAT080D
TM-532
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
1.
Drive manual shaft oil seal into transaxle case using suitable
tool.
CAUTION:
• Do not reuse manual shaft oil seal.
• Apply ATF to outer surface of manual shaft oil seal.
2.
Install parking rod to parking rod plate.
3.
Insert manual shaft (1) to transaxle case, and install manual
plate (2) to manual shaft (1).
4.
Install parking rod plate (with parking rod) (3) to manual shaft
(1).
5.
Align groove of manual shaft and hole of transaxle case using
suitable tool (A).
6.
Drive retaining pin of manual shaft into transaxle case using Tool
(B).
CAUTION:
Do not reuse retaining pin.
7.
Set parking rod plate (1) onto manual shaft, and drive retaining
pin (2) of parking rod plate (1) using Tool (A).
CAUTION:
The retaining pin end should protrude approx. 3mm (0.12
in) (B) from the outer surface of parking rod plate (1).
8.
Set manual plate (1) onto manual shaft, and drive retaining pin
(2) of manual plate (1) using Tool (A).
CAUTION:
The retaining pin end should protrude approx. 3mm (0.12
in) (B) from the outer surface of manual plate (1).
SAT081D
SCIA7005E
Tool number B:
ST23540000
SCIA7006E
Tool number A:
ST23540000
SCIA7107E
Tool number A:
ST23540000
SCIA7108E
REPAIR FOR COMPONENT PARTS
TM-533
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
9.
Install detent spring on transaxle case.
10. Tighten detent spring bolt to the specified torque. Refer to
.
Oil Pump
INFOID:0000000001731436
COMPONENTS
DISASSEMBLY
1.
Remove seal rings (1) from oil pump assembly (2).
SAT042F
1.
Oil pump housing oil seal
2.
Oil pump housing
3.
Outer gear
4.
Inner gear
5.
Oil pump cover
6.
Seal ring
SCIA5908J
SCIA7016E
TM-534
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
2.
Remove bolts in the order as shown, and remove oil pump
cover.
3.
Remove inner gear and outer gear from oil pump housing.
4.
Remove oil pump housing oil seal using suitable tool.
CAUTION:
Do not scratch oil pump housing.
INSPECTION
Oil Pump Housing, Oil Pump Cover, Inner Gear and Outer Gear
Check for wear or damage. Replace if necessary.
Side Clearances
SAT091D
SAT092D
SCIA2840E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст