Nissan Tiida C11. Manual — part 74
BRC-62
< ECU DIAGNOSIS >
[ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ECU DIAGNOSIS
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Reference Value
INFOID:0000000001731339
VALUES ON THE DIAGNOSIS TOOL
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the
event the output circuit (harness) is open or short-circuited.
CONSULT-III MONITOR ITEM
Monitor item
Display content
Data monitor
Condition
Reference value in
normal operation
FR LH SENSOR
Wheel speed
0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(
±
10% or less)
Vehicle running
(Note 1)
FR RH SENSOR
Wheel speed
0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(
±
10% or less)
Vehicle running
(Note 1)
RR LH SENSOR
Wheel speed
0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(
±
10% or less)
Vehicle running
(Note 1)
RR RH SENSOR
Wheel speed
0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(
±
10% or less)
Vehicle running
(Note 1)
STOP LAMP SW
Stop lamp switch signal status
When brake pedal is depressed
ON
When brake pedal is released
OFF
BATTERY VOLT
Battery voltage supplied to the ABS actuator
and electric unit (control unit)
Ignition switch ON
10 – 16 V
GEAR
Gear position determined by TCM
1st gear
2nd gear
3rd gear
4th gear
5th gear
1
2
3
4
5
SLCT LVR POSI
A/T selector lever position
P position
R position
N position
D position
P
R
N
D
OFF SW
VDC OFF switch ON/OFF
VDC OFF switch ON
(When VDC OFF indicator lamp is ON)
ON
VDC OFF switch OFF
(When VDC OFF indicator lamp is OFF)
OFF
YAW RATE SEN
Yaw rate detected by yaw rate/side/decel G
sensor
When vehicle is stopped
Approx. 0 d/s
When vehicle turning
−
75 to 75 d/s
ACCEL POS SIG
Throttle actuator opening/closing is dis-
played (linked with accelerator pedal)
Accelerator pedal not depressed (ignition
switch is ON)
0 %
Accelerator pedal depressed (ignition
switch is ON)
0 - 100 %
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-63
< ECU DIAGNOSIS >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SIDE G-SENSOR
Transverse G detected by side G sensor
Vehicle stopped
Approx. 0 m/s
2
Vehicle turning right
Negative value
(m/s
2
)
Vehicle turning left
Positive value
(m/s
2
)
STR ANGLE SIG
Steering angle detected by steering angle
sensor
Straight-ahead
Approx. 0
°
Steering wheel turned
–720 to 720
°
PRESS SENSOR
Brake fluid pressure detected by front pres-
sure sensor
With ignition switch turned ON and brake
pedal released
Approx. 0 bar
With ignition switch turned ON and brake
pedal depressed
–40 to 300 bar
ENGINE SPEED
With engine running
With engine stopped
0 rpm
Engine running
Almost in accor-
dance with tachome-
ter display
FLUID LEV SW
Brake fluid level switch signal status
When brake fluid level switch ON
ON
When brake fluid level switch OFF
OFF
FR RH IN SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
FR RH OUT SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
FR LH IN SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
FR LH OUT SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
RR RH IN SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
Monitor item
Display content
Data monitor
Condition
Reference value in
normal operation
BRC-64
< ECU DIAGNOSIS >
[ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
RR RH OUT SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
RR LH IN SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
RR LH OUT SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
MOTOR RELAY
Motor and motor relay operation
When the motor relay and motor are op-
erating
ON
When the motor relay and motor are not
operating
OFF
ACTUATOR RLY
Actuator relay operation
When the actuator relay is operating
ON
When the actuator relay is not operating
OFF
ABS WARN LAMP
ABS warning lamp
(Note 3)
When ABS warning lamp is ON
ON
When ABS warning lamp is OFF
OFF
OFF LAMP
VDC OFF indicator lamp
(Note 3)
When VDC OFF indicator lamp is ON
ON
When VDC OFF indicator lamp is OFF
OFF
SLIP LAMP
SLIP indicator lamp
(Note 3)
When SLIP indicator lamp is ON
ON
When SLIP indicator lamp is OFF
OFF
4WD FAIL REQ
(Note 2)
Transfer control unit fail-safe signal
When transfer control unit is in fail-safe
mode
ON
When transfer control unit is normal
OFF
BST OPER SIG
Not applied but displayed
—
OFF
EBD SIGNAL
EBD operation
EBD is active
ON
EBD is inactive
OFF
ABS SIGNAL
ABS operation
ABS is active
ON
ABS is inactive
OFF
TCS SIGNAL
TCS operation
TCS is active
ON
TCS is inactive
OFF
VDC SIGNAL
VDC operation
VDC is active
ON
VDC is inactive
OFF
EBD FAIL SIG
EBD fail-safe signal
In EBD fail-safe
ON
EBD is normal
OFF
ABS FAIL SIG
ABS fail-safe signal
In ABS fail-safe
ON
ABS is normal
OFF
Monitor item
Display content
Data monitor
Condition
Reference value in
normal operation
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-65
< ECU DIAGNOSIS >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
TCS FAIL SIG
TCS fail-safe signal
In TCS fail-safe
ON
TCS is normal
OFF
VDC FAIL SIG
VDC fail-safe signal
In VDC fail-safe
ON
VDC is normal
OFF
CRANKING SIG
Crank operation
Crank is active
ON
Crank is inactive
OFF
CV1
VDC switch-over valve
When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
CV2
VDC switch-over valve
When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
SV1
VDC switch-over valve
When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
SV2
VDC switch-over valve
When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON)
OFF
DECEL G-SEN
Longitudinal acceleration detected by Decel
G-Sensor
Vehicle stopped
Approx. 0 G
Vehicle running
-1.7 to 1.7 G
EBD WARN LAMP
EBD warning lamp
(Note 3)
When EBD warning lamp is ON
ON
When EBD warning lamp is OFF
OFF
N POSI SIG
PNP switch signal ON/OFF condition
A/T shift position = N position
ON
A/T shift position = other than N position
OFF
P POSI SIG
PNP switch signal ON/OFF condition
A/T shift position = P position
ON
A/T shift position = other than P position
OFF
R POSI SIG
PNP switch signal ON/OFF condition
A/T shift position = R position
ON
A/T shift position = other than R position
OFF
2WD/4WD
Drive axle
2WD model
2WD
4WD model
4WD
PRESS SEN2
Brake fluid pressure detected by rear pres-
sure sensor
With ignition switch turned ON and brake
pedal released
Approx. 0 bar
With ignition switch turned ON and brake
pedal depressed
–40 to 300 bar
Monitor item
Display content
Data monitor
Condition
Reference value in
normal operation
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст