Nissan Tiida C11. Manual — part 387
EC-198
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
P0335 CKP SENSOR (POS)
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001670962
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E15. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK CRANKSHAFT POSITION (CKP) SENSOR (POS) POWER SUPPLY CIRCUIT-I
1.
Disconnect crankshaft position (CKP) sensor (POS) harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between CKP sensor (POS) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 3.
3.
CHECK CRANKSHAFT POSITION (CKP) SENSOR (POS) POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit.
4.
CHECK CRANKSHAFT POSITION (CKP) SENSOR (POS) POWER SUPPLY CIRCUIT-III
Check harness for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair short to ground or short to power in harness or connectors.
5.
CHECK REFRIGERANT PRESSURE SENSOR
.
CKP sensor (POS)
Ground
Voltage
Connector
Terminal
F15
1
Ground
Approx. 5V
CKP sensor (POS)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F15
1
F11
75
Existed
ECM
Sensor
Connector
Terminal
Name
Connector
Terminal
F11
74
Refrigerant pressure sensor
E17
3
75
CKP sensor (POS)
F15
1
E16
102
APP sensor 2
E12 (LHD models)
M204 (RHD models)
5
P0335 CKP SENSOR (POS)
EC-199
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace refrigerant pressure sensor.
6.
CHECK APP SENSOR
EC-293, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> GO TO 7.
7.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly.
2.
EC-26, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Require-
.
>> INSPECTION END
8.
CHECK CKP SENSOR (POS) GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK CKP SENSOR (POS) INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
10.
CHECK CRANKSHAFT POSITION SENSOR (POS)
EC-200, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Replace crankshaft position sensor (POS).
11.
CHECK GEAR TOOTH
Visually check for chipping signal plate gear tooth.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Replace the signal plate.
12.
CHECK INTERMITTENT INCIDENT
GI-55, "Intermittent Incident"
.
CKP sensor (POS)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F15
2
F11
62
Existed
CKP sensor (POS)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F15
3
F11
61
Existed
EC-200
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
P0335 CKP SENSOR (POS)
>> INSPECTION END
Component Inspection
INFOID:0000000001670963
1.
CHECK CRANKSHAFT POSITION SENSOR (POS)-I
1.
Turn ignition switch OFF.
2.
Loosen the fixing bolt of the sensor.
3.
Disconnect crankshaft position sensor (POS) harness connector.
4.
Remove the sensor.
5.
Visually check the sensor for chipping.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace crankshaft position sensor (POS).
2.
CHECK CRANKSHAFT POSITION SENSOR (POS)-II
Check resistance between crankshaft position sensor (POS) terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace crankshaft position sensor (POS).
PBIA9209J
Terminals (Polarity)
Resistance [at 25
°
C (77
°
F)]
1 (+) - 2 (-)
Except 0 or
∞
Ω
1 (+) - 3 (-)
2 (+) - 3 (-)
P0340 CMP SENSOR (PHASE)
EC-201
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0340 CMP SENSOR (PHASE)
Description
INFOID:0000000001670964
The camshaft position sensor (PHASE) senses the retraction of
camshaft (INT) to identify a particular cylinder. The camshaft position
sensor (PHASE) senses the piston position.
When the crankshaft position sensor (POS) system becomes inoper-
ative, the camshaft position sensor (PHASE) provides various con-
trols of engine parts instead, utilizing timing of cylinder identification
signals.
The sensor consists of a permanent magnet and Hall IC.
When engine is running, the high and low parts of the teeth cause
the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor changes.
ECM receives the signals as shown in the figure.
DTC Logic
INFOID:0000000001670965
DTC DETECTION LOGIC
NOTE:
If DTC P0340 is displayed with DTC P1129, first perform the trouble diagnosis for DTC P1129. Refer to
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5V with igni-
tion switch ON.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE-I
1.
Start engine and let it idle for at least 5 seconds.
If engine does not start, crank engine for at least 2 seconds.
2.
Check 1st trip DTC.
PBIA9875J
JMBIA0714GB
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0340
Camshaft position sen-
sor (PHASE) circuit
• The cylinder No. signal is not sent to ECM for
the first few seconds during engine cranking.
• The cylinder No. signal is not sent to ECM
during engine running.
• The cylinder No. signal is not in the normal
pattern during engine running.
• Harness or connectors
(The sensor circuit is open or shorted)
• Camshaft position sensor (PHASE)
• Camshaft (INT)
• Starter motor
• Starting system circuit
• Dead (Weak) battery
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст