Nissan Tiida C11. Manual — part 1121

PWC-20

< COMPONENT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect main power window and door lock/unlock switch and
rear power window switch LH.

3.

Check continuity between main power window and door lock/
unlock switch connector (A) and rear power window switch LH
connector (B).

4.

Check continuity between main power window and door lock/unlock switchh connector (A) and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-55, "Intermittent Incident"

.

NO

>> Repair or replace harness.

3.

CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH RH)

1.

Turn ignition switch OFF.

2.

Disconnect main power window and door lock/unlock switch and
rear power window switch RH.

3.

Check continuity between main power window and door lock/
unlock switch connector (A) and rear power window switch RH
connector (B).

4.

Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-55, "Intermittent Incident"

.

NO

>> Repair or replace harness.

4.

CHECK HARNESS CONTINUITY

Main power window

and door lock/unlock

switch connector

Terminal

Rear power win-

dow switch LH

connector

Terminal

Continuity

D7 (A)

1

D203 (B)

2

Yes

3

3

Main power window and

door lock/unlock switch

connector

Terminal

Ground

Continuity

D7 (A)

1

No

3

ALKIA0278ZZ

Main power window

and door lock/unlock

switch connector

Terminal

Rear power

window switch

RH connector

Terminal

Continuity

D7 (A)

5

D303 (B)

3

Yes

7

2

Main power window

and door lock/unlock

switch connector

Terminal

Ground

Continuity

D7 (A)

5

No

7

ALKIA0279ZZ

POWER SUPPLY AND GROUND CIRCUIT

PWC-21

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

1.

Disconnect BCM and rear power window switch.

2.

Check continuity between BCM connector (A) and rear power
window switch connector (B).

3.

Check continuity between BCM connector and ground.

Is the inspection result normal?

YES

>> GO TO 5

NO

>> Repair or replace harness.

5.

CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.
Refer to

PWC-21, "REAR POWER WINDOW SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-55, "Intermittent Incident"

.

NO

>> Replace rear power window switch. Refer to

INT-13, "Removal and Installation"

.

REAR POWER WINDOW SWITCH : Component Inspection

INFOID:0000000001696315

COMPONENT INSPECTION

1.

CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.

Is the inspection result normal?

YES

>> Rear power window switch is OK.

NO

>> Replace rear power window switch. Refer to

INT-13, "Removal and Installation"

.

BCM

connector

Terminal

Rear power window switch

connector

Terminal

Continuity

M20 (A)

68

LH

D203 (B)

1

Yes

RH

D303 (B)

BCM connector

Terminal

Ground

Continuity

M20

68

No

ALKIA1017ZZ

Terminal

Power window switch condition

Continuity

1

5

UP

Yes

3

4

3

4

NEUTRAL

2

5

1

4

DOWN

2

5

ALKIA0289ZZ

PWC-22

< COMPONENT DIAGNOSIS >

POWER WINDOW MOTOR

POWER WINDOW MOTOR

DRIVER SIDE

DRIVER SIDE : Description

INFOID:0000000001696316

Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch.

DRIVER SIDE : Component Function Check

INFOID:0000000001696317

1.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) CIRCUIT

Does front power window motor (driver side) operate with the main power window and door lock/unlock
switch?

Is the inspection result normal?

YES

>> Front power window motor (driver side) is OK.

NO

>> Refer to

PWC-22, "DRIVER SIDE : Diagnosis Procedure"

.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000001696318

Front Power Window Motor LH Circuit Check

1.

CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL

1.

Disconnect front power window motor (driver side).

2.

Turn ignition switch ON.

3.

Check voltage between front power window motor (driver side)
connector and ground.

Is the measurement value within the specification?

YES

>> GO TO 2

NO

>> Replace main power window and door lock/unlock switch. Refer to

INT-13, "Removal and Installa-

tion"

. After that, refer to

PWC-4, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGA-

TIVE TERMINAL : Special Repair Requirement"

.

2.

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect main power window and door lock/unlock switch.

3.

Check continuity between main power window and door lock/unlock switch connector and front power
window motor (driver side) connector.

( ): RHD

Terminal

Main power win-

dow and door

lock/unlock

switch condition

Voltage (V)

(Approx.)

(+)

(–)

Front power

window motor

(driver side)

connector

Terminal

D9

2

Ground

UP

Battery voltage

DOWN

0

3

UP

0

DOWN

Battery voltage

ALKIA1094ZZ

Main power window

and door lock/unlock

switch

connector

Terminal

Front power window

motor LH connector

Terminal

Continuity

D7

8 (16)

D9

2

Yes

11 (12)

3

POWER WINDOW MOTOR

PWC-23

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

4.

Check continuity between main power window and door lock/unlock switch connector and ground.

( ): RHD

Is the inspection result normal?

YES

>> GO TO 3

NO

>> Repair or replace harness.

3.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE)

Check front power window motor (driver side).
Refer to

PWC-23, "DRIVER SIDE : Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-55, "Intermittent Incident"

.

NO

>> Replace front power window motor (driver side). Refer to

GW-14, "Removal and Installation"

.

After that, refer to

PWC-4, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE

TERMINAL : Special Repair Requirement"

.

DRIVER SIDE : Component Inspection

INFOID:0000000001696319

COMPONENT INSPECTION

1.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE)

Does motor operate by connecting the battery voltage directly to power window motor?

Is the inspection result normal?

YES

>> Front power window motor (driver side) is OK.

NO

>> Replace front power window motor (driver side). Refer to

GW-14, "Removal and Installation"

.

After that, refer to

PWC-4, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE

TERMINAL : Special Repair Requirement"

.

DRIVER SIDE : Special Repair Requirement

INFOID:0000000001696320

1.

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.
Refer to

PWC-4, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

.

Is the inspection result normal?

YES

>> GO TO 2

NO

>> Check intermittent incident. Refer to

GI-55, "Intermittent Incident"

.

2.

CHECK ANTI-PINCH OPERATION

Check anti-pinch operation.
Refer to

PWC-4, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Refer to

PWC-29, "DRIVER SIDE : Component Function Check"

.

Main power window and

door lock/unlock switch

connector

Terminal

Ground

Continuity

D7

8 (16)

No

11 (12)

Terminal

Motor condition

(+)

(–)

2

3

DOWN

3

2

UP