Nissan Tiida C11. Manual — part 821
GW-22
< ON-VEHICLE REPAIR >
REAR DOOR GLASS AND REGULATOR
5.
Pull out the partition glass in the direction as shown.
6.
If equipped, operate the power window switch to raise/lower the
door window until the glass bolts can be seen.
NOTE:
Connect the harness connector to the power window switch.
7.
Remove the rear door glass bolts.
8.
Pull out the rear door glass toward the outside of the door to
remove.
9.
Remove the door glass run from the door panel.
Installation
Installation is in the reverse order of removal.
REGULATOR ASSEMBLY
Removal
1.
Remove and position aside the rear door finisher. Refer to
INT-13, "Removal and Installation"
.
2.
Disconnect the harness connector of rear speaker.
3.
Position aside the sealing screen.
NOTE:
If the sealing screen is reused, cut the butyl-tape so that a part of butyl-tape remains on the sealing screen.
4.
If equipped, operate the power window switch to raise/lower the
door window until the glass bolts can be seen.
NOTE:
Connect the harness connector to the power window switch.
5.
Remove the rear door glass bolts.
6.
Raise up the door glass and hold with a suction lifter A.
PIIB2636J
PIIB2637J
PIIB2637J
PIIB3511J
REAR DOOR GLASS AND REGULATOR
GW-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
7.
Remove the regulator bolts, and then remove the regulator
assembly from the door panel.
Installation
Installation is in the reverse order of removal.
Inspection after Removal
Check the regulator assembly for the following. [If a problem is
detected, grease or replace it as shown].
• Gear wear
• Regulator deformation
• Grease condition for each sliding part
Disassembly and Assembly
INFOID:0000000001716847
POWER WINDOW REGULATOR ASSEMBLY
Disassembly
Remove the power window motor from the regulator assembly.
Assembly
Assembly is in the reverse order of disassembly.
Inspection after Installation
INFOID:0000000001716848
FITTING INSPECTION
• Make sure the glass is securely fit into the glass run groove.
• Lower the glass slightly [approx. 10 to 20 mm (0.39 to 0.79 in)], and make sure the clearance to the sash is
parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide rail
bolts, and glass and carrier plate bolts to correct the glass position.
PIIB6315E
SIIA1787J
HA-1
VENTILATION, HEATER & AIR CONDITIONER
C
D
E
F
G
H
J
K
L
M
SECTION
HA
A
B
HA
N
O
P
CONTENTS
HEATER & AIR CONDITIONING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover
. ..
Precaution for Working with HFC-134a (R-134a) . ..
General Refrigerant Precaution . . . . . . . ....
Oil Precaution . . . . . . . . . . . . . . ....
Precaution for Refrigerant Connection . . . . . ..
Precaution for Service of Compressor . . . . . ..
Precaution for Service Equipment . . . . . . .....
Precaution for Leak Detection Dye . . . . . . .
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . ..
HFC-134a (R-134a) Service Tool and Equipment
Commercial Service Tool . . . . . . . . . .
FUNCTION DIAGNOSIS . . . . . . . ..
REFRIGERATION SYSTEM . . . . . . . ..
Refrigerant Cycle . . . . . . . . . . . . .
Refrigerant System Protection . . . . . . . .
OIL . . . . . . . . . . . . . . . . . ..
Maintenance of Oil Quantity in Compressor . . ...
ON-VEHICLE MAINTENANCE . . . . .
OIL . . . . . . . . . . . . . . . . . ..
Maintenance of Oil Quantity in Compressor . . ...
REFRIGERATION SYSTEM . . . . . . . ..
HFC-134a (R-134a) Service Procedure . . . . ..
Checking of Refrigerant Leaks . . . . . . . .
FLUORESCENT LEAK DETECTOR . . . . .
Checking System for Leaks Using the Fluorescent
Leak Detector . . . . . . . . . . . . . . ..
Dye Injection . . . . . . . . . . . . . . .
ELECTRICAL LEAK DETECTOR . . . . .
Electronic Refrigerant Leak Detector . . . . . ...
ON-VEHICLE REPAIR . . . . . . . . .
REFRIGERATION SYSTEM . . . . . . . .
Component . . . . . . . . . . . . . . . ..
HFC-134a (R-134a) Service Procedure . . . . ..
COMPRESSOR . . . . . . . . . . . . .
Removal and Installation of Compressor -
MR18DE . . . . . . . . . . . . . . . . ..
Removal and Installation of Compressor -
HR16DE . . . . . . . . . . . . . . . . ..
Removal and Installation of Compressor - K9K . ...
LOW-PRESSURE FLEXIBLE HOSE . . . .
Removal and Installation of Low-Pressure Flexi-
ble Hose - MR18DE, HR16DE . . . . . . . .
Removal and Installation of Low-Pressure Flexi-
ble Hose - K9K . . . . . . . . . . . . . .
LOW-PRESSURE PIPE . . . . . . . . .
Removal and Installation of Low-Pressure Pipe -
K9K . . . . . . . . . . . . . . . . . . ..
HIGH-PRESSURE FLEXIBLE HOSE . . . ...
Removal and Installation of High-Pressure Flexi-
ble Hose - MR18DE, HR16DE . . . . . . . .
Removal and Installation of High-Pressure Flexi-
ble Hose - K9K . . . . . . . . . . . . . .
HIGH-PRESSURE PIPE . . . . . . . . .
Removal and Installation of High-Pressure Pipe -
MR18DE, HR16DE . . . . . . . . . . . . ..
Removal and Installation of High-Pressure Pipe -
K9K . . . . . . . . . . . . . . . . . . ..
CONDENSER . . . . . . . . . . . . .
Removal and Installation of Condenser -
MR18DE, HR16DE . . . . . . . . . . . . ..
HA-2
Removal and Installation for Condenser - K9K . ..
AMBIENT SENSOR . . . . . . . . . . ...
Removal and Installation of Ambient Sensor -
MR18DE, HR16DE and K9K . . . . . . . . ..
REFRIGERANT PRESSURE SENSOR . . .
Removal and Installation of Refrigerant Pressure
Sensor - MR18DE, HR16DE . . . . . . . . ..
Removal and Installation of Refrigerant Pressure
Sensor - K9K . . . . . . . . . . . . . . ..
EXPANSION VALVE . . . . . . . . . . .
Removal and Installation of Expansion Valve -
MR18DE, HR16DE and K9K . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
MR18DE Engine . . . . . . . . . . . . . .
HR16DE Engine . . . . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст