Nissan Tiida C11. Manual — part 672
EM-40
< ON-VEHICLE REPAIR >
[HR16DE]
OIL PAN (LOWER)
OIL PAN (LOWER)
Exploded View
INFOID:0000000001381406
Removal and Installation
INFOID:0000000001381407
REMOVAL
1.
Drain engine oil. Refer to
.
2.
Remove the oil pan (lower) with the following procedure.
a.
Loosen bolts in the reverse of the order shown.
b.
Insert the seal cutter [SST: KV10111100] between oil pan
(upper) and oil pan (lower).
CAUTION:
• Be careful not to damage the mating surface.
• A more adhesive liquid gasket is applied compared to pre-
vious types when shipped, so it should not be forced off
using a flat- bladed screwdriver, etc.
1.
Rear oil seal
2.
O-ring
3.
Oil pan (upper)
4.
Chain tensioner
5.
Oil pump drive chain
6.
Crankshaft sprocket
7.
Oil pump sprocket
8.
Oil pan drain plug
9.
Washer
10.
Oil pan (lower)
11.
Oil filter stud bolt
12.
Oil filter
13.
Oil level sensor
A.
Refer to
B.
Refer to
C.
Oil pan side
JPBIA0553GB
: Engine front
PBIC4345E
OIL PAN (LOWER)
EM-41
< ON-VEHICLE REPAIR >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
INSTALLATION
1.
Install oil pan (lower) with the following procedure.
a.
Use scraper to remove old liquid gasket from mating surfaces.
• Also remove the old liquid gasket from mating surface of oil pan (upper).
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Never scratch or damage the mating surfaces when cleaning off old liquid gasket.
b.
Apply a continuous bead of liquid gasket (A) with the tube
presser (commercial service tool) to areas shown.
Use Genuine Liquid Gasket or equivalent.
CAUTION:
Attaching should be done within 5 minutes after coating.
c.
Tighten bolts in the numerical order shown in the figure.
2.
Install oil pan drain plug.
• For installation direction of washer. Refer to
.
3.
Install in the reverse order of removal, for the rest of parts.
CAUTION:
Pour engine oil at least 30 minutes after oil pan is installed.
Inspection
INFOID:0000000001381408
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leak of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
: Engine out side
PBIC5006E
: Engine front
PBIC4345E
EM-42
< ON-VEHICLE REPAIR >
[HR16DE]
OIL PAN (UPPER) AND OIL STRAINER
OIL PAN (UPPER) AND OIL STRAINER
Component
INFOID:0000000001532078
Removal and Installation
INFOID:0000000001532079
NOTE:
The oil strainer and oil pump are included in the oil pan (upper). Individual disassembly is prohibited.
REMOVAL
NOTE:
When removing oil pan (lower) only, steps “2” and “3” are not necessary. Perform step “5” after completing
step “4”.
1.
Remove engine undercover using power tool.
2.
Remove engine and transaxle assembly from the vehicle, and then separate engine and transaxle. Refer
to
EM-89, "Removal and Installation"
.
3.
Install engine assembly to widely use engine stand. Refer to
.
4.
Drain engine oil. Refer to
.
5.
Remove the oil pan (lower) using the following procedure.
1.
Rear oil seal
2.
O-ring
3.
Oil pan (upper)
4.
Chain tensioner
5.
Oil pump drive chain
6.
Crankshaft sprocket
7.
Oil pump sprocket
8.
Oil pan drain plug
9.
Washer
10. Oil pan (lower)
11.
Oil filter stud bolt
12.
Oil filter
13. Oil level sensor
A.
B.
Refer to
C.
Oil pan side
JPBIA0553GB
OIL PAN (UPPER) AND OIL STRAINER
EM-43
< ON-VEHICLE REPAIR >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Loosen bolts in the reverse of the order shown.
b.
Insert the seal cutter (SST: KV10111100) between oil pan
(upper) and oil pan (lower).
CAUTION:
• Be careful not to damage the mating surface.
• A more adhesive liquid gasket is applied compared to pre-
vious types when shipped, so it should not be forced off
using a flat- bladed screwdriver, etc.
6.
Remove oil level gauge.
7.
Remove front cover and timing chain. Refer to
EM-50, "Removal and Installation"
.
8.
Remove oil pump sprocket and crankshaft sprocket together with oil pump drive chain. Refer to
9.
Remove oil pan (upper) using the following procedure.
a.
Loosen oil pan (upper) mounting bolts in the reverse of the order
shown.
b.
Insert a flat-bladed offset screwdriver into the arrow (
) in the
figure and open up a crack between the oil pan (upper) cylinder
block.
c.
Insert the seal cutter (SST: KV10111100) between remove the
oil pan (upper) and cylinder block.Slide seal cutter by tapping on
the side of tool with a hammer.
CAUTION:
• Be careful not to damage the mating surface.
• A more adhesive liquid gasket is applied compared to pre-
vious types when shipped, so it should not be forced off using a screwdriver, etc. outside the
indicated location.
• Do not remove oil pump and oil strainer from oil pan (upper).
10. Remove rear oil seal from crankshaft.
INSTALLATION
1.
Install the oil pan (upper) in the following procedure.
a.
Use scraper to remove old liquid gasket from mating surfaces.
• Also remove the old liquid gasket from mating surface of cylinder block.
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Do not scratch or damage the mating surfaces when cleaning off old liquid gasket.
b.
Install O-ring to the cylinder block.
: Engine front
PBIC4345E
: Engine front
MBIB1374E
: Engine front
MBIB1375E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст