Nissan Tiida C11. Manual — part 1249

DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH

TM-47

< COMPONENT DIAGNOSIS >

[TYPE 1 (4AT: RE4F03B)]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

1.

Check continuity between PNP switch harness connector termi-
nals.

2.

If NG, check again with control cable (2) disconnected from
manual shaft of A/T assembly. Refer to step 1.
(1): Lock nut
(3): Manual shaft

3.

If OK on step 2, adjust control cable (2). Refer to

TM-204,

"Adjustment of A/T Position"

.

4.

If NG on step 2, remove PNP switch from A/T and check conti-
nuity of PNP switch terminals. Refer to step 1.

5.

If OK on step 4, adjust PNP switch. Refer to

TM-195, "Park/Neu-

tral Position (PNP) Switch"

.

6.

If NG on step 4, replace PNP switch. Refer to

TM-195, "Park/

Neutral Position (PNP) Switch"

.

Selector lever position

Connector

Terminal

Continuity

“P”

F25

1 - 2, 3 - 7

Yes
*Continuity
should not
exist in posi-
tions other
than the
specified
positions.

“R”

3 - 8

“N”

1 - 2, 3 - 9

“D”

3 - 6

“2”

3 - 5

“1”

3 - 4

SCIA5588E

SCIA6370J

TM-48

< COMPONENT DIAGNOSIS >

[TYPE 1 (4AT: RE4F03B)]

DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT

DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT

Description

INFOID:0000000001694291

The A/T fluid temperature sensor detects the A/T fluid temperature and sends a signal to the TCM.

CONSULT-III Reference Value in Data Monitor Mode

INFOID:0000000001694292

Remarks: Specification data are reference values.

On Board Diagnosis Logic

INFOID:0000000001694293

• This is an OBD self-diagnostic item.
• Diagnostic trouble code “P0710 ATF TEMP SEN/CIRC” with CONSULT-III is detected when TCM receives

an excessively low or high voltage from the sensor.

Possible Cause

INFOID:0000000001694294

• Harness or connector

(The sensor circuit is open or shorted.)

• A/T fluid temperature sensor

DTC Confirmation Procedure

INFOID:0000000001694295

CAUTION:

• Always drive vehicle at a safe speed.
• If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at

least 10 seconds before continuing.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

WITH CONSULT-III

1.

Turn ignition switch ON and select “DATA MONITOR” mode for “A/T” with CONSULT-III.

2.

Touch “START”.

3.

Start engine and maintain the following conditions for at least 10 minutes (Total). (It is not necessary to
maintain continuously.)
ENGINE SPEED: 450 rpm or more
VEHICLE SPEED: 10 km/h (6 MPH) or more
THROTTLE POSI: More than 1.0/8
SLCT LVR POSI: “D” position

4.

If the check result is NG, go to

TM-48, "Diagnosis Procedure"

.

WITH GST

Follow the procedure “With CONSULT-III”.

Diagnosis Procedure

INFOID:0000000001694297

1.

CHECK INPUT SIGNAL

With CONSULT-III

1.

Start engine.

2.

Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-III.

3.

Read out the value of “FLUID TEMP SE”.

Item name

Condition

Display value (Approx.)

FLUID TEMP SE

When A/T fluid temperature is 20

°

C (68

°

F).

1.5V

When A/T fluid temperature is 80

°

C (176

°

F).

0.5V

Item name

Condition

Display value
(Approx.)

FLUID TEMP
SE

When A/T fluid temperature is 20

°

C (68

°

F).

1.5V

When A/T fluid temperature is 80

°

C (176

°

F).

0.5V

DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT

TM-49

< COMPONENT DIAGNOSIS >

[TYPE 1 (4AT: RE4F03B)]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Without CONSULT-III

1.

Start engine.

2.

Check voltage TCM connector terminals while warming up A/T.

OK or NG

OK

>> GO TO 7.

NG

>> GO TO 2.

2.

DETECT MALFUNCTIONING ITEMS

Check the following.
• Harness for short or open between TCM, ECM and terminal cord assembly
• Ground circuit for ECM.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

CHECK FLUID TEMPERATURE SENSOR CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect the TCM connector.

3.

Check resistance between TCM connector terminals.

OK or NG

OK

>> GO TO 7.

NG

>> GO TO 4.

4.

CHECK HARNESS BETWEEN TCM AND TERMINAL CORD ASSEMBLY HARNESS CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect terminal cord assembly harness connector and TCM connector.

3.

Check continuity between terminal cord assembly harness con-
nector terminal and TCM connector terminal.

4.

If OK, check harness for short to ground and short to power.

5.

If OK, check continuity between ground and transaxle assembly.

6.

Reinstall any part removed.

Item

Connec-

tor

Terminal

Condition

Judge-

ment stan-

dard

(Approx.)

A/T fluid
temperature
sensor

E32

47 - 42

When A/T fluid tempera-

ture is 20

°

C (68

°

F).

1.5V

When A/T fluid tempera-

ture is 80

°

C (176

°

F).

0.5V

SCIA2658E

Item

Connector

Terminal

Tempera-

ture [

°

C (

°

F)]

Resistance

(Approx.)

A/T fluid
temperature
sensor

E32

47 - 42

20 (68)

2.5 k

Ω

80 (176)

0.3 k

Ω

SCIA2338E

Item

Connector

Terminal Continuity

TCM

E32

42

Yes

Terminal cord assembly
harness connector

F30

7

TCM

E32

47

Yes

Terminal cord assembly
harness connector

F30

6

SCIA2660E

TM-50

< COMPONENT DIAGNOSIS >

[TYPE 1 (4AT: RE4F03B)]

DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT

OK or NG

OK

>> GO TO 5.

NG

>> Repair open circuit or short to ground or short to power in harness or connectors.

5.

CHECK A/T FLUID TEMPERATURE SENSOR WITH TERMINAL CORD ASSEMBLY

1.

Turn ignition switch OFF.

2.

Disconnect terminal cord assembly harness connector in engine room.

3.

Check resistance between terminal cord assembly harness con-
nector terminals.

4.

Reinstall any part removed.

OK or NG

OK

>> GO TO 6.

NG

>> Repair or replace damaged parts.

6.

DETECT MALFUNCTIONING ITEM

1.

Remove oil pan. Refer to

TM-191, "Control Valve Assembly and Accumulators"

.

2.

Check the following.

-

A/T fluid temperature sensor

•

Check resistance between terminal cord assembly harness con-
nector terminals while changing temperature as shown.

-

Harness of terminal cord assembly for short or open

OK or NG

OK

>> GO TO 7.

NG

>> Repair or replace damaged parts.

7.

CHECK DTC

Perform

TM-48, "DTC Confirmation Procedure"

.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 8.

8.

CHECK TCM

1.

Check TCM input/output signal. Refer to

TM-119, "Reference Value"

.

2.

If NG, recheck TCM pin terminals for damage or loose connection with harness connector.

OK or NG

OK

>> INSPECTION END

NG

>> Repair or replace damaged parts.

Component Inspection

INFOID:0000000001694298

A/T FLUID TEMPERATURE SENSOR

Temperature [

°

C (

°

F)]

Resistance (Approx.)

20 (68)

2.5 k

Ω

80 (176)

0.3 k

Ω

SCIA4948E

Temperature [

°

C (

°

F)]

Resistance (Approx.)

20 (68)

2.5 k

Ω

80 (176)

0.3 k

Ω

SAT298F