Nissan Tiida C11. Manual — part 200
DLK-210
< PREPARATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000001315830
Tool name
Description
Engine ear
Locating the noise
Remover tool
Remove the clips, pawls, and metal clips
Power tool
Removing nuts and bolts
SIIA0995E
PIIB7923J
PIIB1407E
PRE-INSPECTION FOR DIAGNOSTIC
DLK-211
< ON-VEHICLE MAINTENANCE >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ON-VEHICLE MAINTENANCE
PRE-INSPECTION FOR DIAGNOSTIC
Basic Inspection
INFOID:0000000001396666
BASIC INSPECTION
1.
CHECK POWER DOOR LOCK AND UNLOCK SWITCH OPERATION
Check door lock and unlock operation by operating door lock and unlock switch.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
DLK-191, "DOOR LOCK AND UNLOCK SWITCH : Symptom Table"
.
2.
CHECK INTELLIGENT KEY OPERATION
Check door lock and unlock operation by operating the Intelligent Key remote control button.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Refer to
DLK-192, "INTELLIGENT KEY : Symptom Table"
3.
CHECK DOOR REQUEST SWITCH OPERATION
Check door lock and unlock operation by operating door request switch.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Refer to
DLK-193, "DOOR REQUEST SWITCH : Symptom Table"
.
4.
CHECK KEY REMINDER OPERATION
Check key reminder operation. Refer to
DLK-31, "KEY REMINDER : System Description"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Refer to
DLK-194, "KEY REMINDER : Symptom Table"
.
5.
CHECK AUTO DOOR LOCK OPERATION
Check auto door lock operation. Refer to
XX-XX, "*****"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Refer to
DLK-194, "AUTO RELOCK : Symptom Table"
6.
CHECK VEHICLE SPEED SENSING AUTO DOOR LOCK OPERATION
Check vehicle speed sensing auto door lock operation. Refer to
XX-XX, "*****"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Refer to
XX-XX, "*****"
.
7.
CHECK BACK DOOR (HATCHBACK) / TRUNK LID (SEDAN) OPENER OPERATION
Check back door (hatchback)/trunk lid (sedan) opener operation by operating the opener switch.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Refer to
DLK-195, "BACK DOOR OPENER SWITCH : Symptom Table"
8.
CHECK WARNING FUNCTION
Check warning function. Refer to
Is the inspection result normal?
YES
>> GO TO 9.
NO [Buzzer (combination meter)]>> Refer to
DLK-197, "BUZZER (COMBINATION METER) : Symptom
.
DLK-212
< ON-VEHICLE MAINTENANCE >
[WITH I-KEY, WITHOUT SUPER LOCK]
PRE-INSPECTION FOR DIAGNOSTIC
NO (Intelligent Key warning buzzer)>> Refer to
DLK-197, "INTELLIGENT KEY WARNING BUZZER : Symp-
NO (Warning lamp)>> Refer to
DLK-199, "WARNING LAMP : Symptom Table"
NO (Back door open warning)>> Refer to
DLK-200, "BACK DOOR : Symptom Table"
9.
CHECK HAZARD AND BUZZER REMINDER FUNCTION
Check hazard and buzzer reminder function by Intelligent Key or request switch. Refer to
XX-XX, "*****"
.
Is the inspection result normal?
YES
>> GO TO 10.
NO (Hazard warning lamp)>> Refer to
DLK-201, "HAZARD WARNING LAMP : Symptom Table"
NO (Intelligent Key warning buzzer)>> Refer to
DLK-201, "INTELLIGENT KEY WARNING BUZZER : Symp-
10.
CHECK OUT
CHECK OUT.
>> INSPECTION END
HOOD
DLK-213
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOVAL AND INSTALLATION
HOOD
Fitting Adjustment
INFOID:0000000001315831
FRONT END HEIGHT ADJUSTMENT AND LATERAL/LONGITUDINAL CLEARANCE ADJUST-
MENT
1.
Remove the front grille. Refer to
EXT-19, "Removal and Installation"
2.
Remove hood lock. Rotate bumper rubber to adjust height until
hood becomes 1.0 to 1.5 mm lower than the fender.
3.
Position hood lock and engage striker. Check hood lock and
striker for looseness. Tighten lock bolts to the specified torque.
4.
Install the front grille. Refer to
EXT-19, "Removal and Installa-
CAUTION:
Adjust the clearance between hood and other parts so that the
dimensional difference left and right is as follows.
SURFACE MISMATCH ADJUSTMENT
1.
Remove the front grille. Refer to
EXT-19, "Removal and Installation"
2.
Release hood lock, and adjust surface level difference of hood, fender, and headlamp according to the fit-
ting standard dimension, using RH and LH bumper rubbers.
3.
Install and align the hood lock until the center of the striker and the hood lock are vertically aligned.
PIIB6508E
Hood and headlamp (B - B)
: Less than 2.0 mm (0.08 in)
Hood and fender (C - C)
: Less than 1.5 mm (0.06 in)
Hood and fender (D - D)
: Less than 1.5 mm (0.06 in)
PIIB2526J
Hood and front bumper (A - A)
: -1.3 - 2.7 mm (-0.05 - 0.11 in)
Hood and fender (D - D)
: -0.4 - 1.7 mm (-0.16 - 0.07 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст