Nissan Tiida C11. Manual — part 58
REAR DISC BRAKE
BR-39
< DISASSEMBLY AND ASSEMBLY >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
5.
Attach the sliding pin bolt and sliding pin boot to the torque member.
6.
Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the rear of the pad and to both sides
of the shim, and attach the inner shim and shim cover to the inner pad, and the outer shim and outer shim
cover to the outer pad.
7.
Attach the pad retainer and pad to the torque member.
CAUTION:
When attaching the pad retainer, attach it firmly so that it
does not float up higher than the torque member, as shown
in the figure.
8.
After assembling shims and shim covers to pad, install it to the
torque member.
9.
Install cylinder body. Tighten sliding pin bolts to the specified
torque.
DISC ROTOR INSPECTION
Visual Inspection
Check surface of the disc rotor for uneven wear, cracks, and serious damage. If any non-standard condition is
detected, replace applicable part.
Runout Inspection
1.
Using wheel nuts, fix disc rotor to the wheel hub in two or more positions.
2.
Inspect runout using a dial gauge.
CAUTION:
Before measuring, make sure the axle endplay is 0 mm (0
in).
3.
If runout is outside the limit, find the minimum runout point by
shifting mounting positions of the disc rotor and wheel hub by
one hole.
Thickness Inspection
Using a micrometer, check thickness of the disc rotor. If thickness is
not within specification, replace disc rotor.
PFIA0273E
Measurement position
: At a point 10 mm (0.39 in)
from outer edge of the disc.
Runout limit (with it at-
tached to the vehicle)
: 0.07 mm (0.0028 in) or less
BRA0013D
Standard thickness
: 9.0 mm (0.350 in)
Minimum thickness
: 8.0 mm (0.310 in)
Maximum uneven wear
(measured at 8 positions)
: 0.015 mm (0.0006 in) or
less
SBR020B
BR-40
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000001716911
Brake Pedal
INFOID:0000000001716912
Unit: mm (in)
Check Valve
INFOID:0000000001716913
Brake Booster
INFOID:0000000001716914
Vacuum type
Front Disc Brake
INFOID:0000000001716915
Unit: mm (in)
Front brake
Brake model
CLZ25VA
Cylinder bore diameter
57.2 mm (2.252 in)
Pad
Length
×
width
×
thickness
125.6 mm
×
46.0 mm
×
9.5 mm
(4.945 in
×
1.811 in
×
0.374 in)
Rotor outer diameter
×
thickness
280 mm
×
24.0 mm (11.02 in
×
0.945 in)
Rear brake
Brake model
—
Cylinder bore diameter
34.93 mm (1.375 in)
Pad thickness
8.5 mm (0.335 in)
Rotor outer diameter
×
thickness
292 mm
×
9.0 mm
(11.50 in
×
0.354 in)
Master cylinder
Cylinder bore diameter
22.22 mm (0.875 in)
Control valve
Valve model
Electric brake force distribution
Brake booster
Booster model
C255
Diaphragm diameter
255 mm (10.04 in)
Recommended brake fluid
Brake pedal free height (from dash panel top surface)
A/T model
172.4 - 182.4 (6.79 - 7.18)
M/T models
162.3 - 172.3 (6.39 - 6.78)
Brake pedal depressed height
[under a force of 490 N (50 kg-f, 110 lb-f) with the engine running]
A/T model
98 (3.86) or more
M/T models
90 (3.54) or more
Clearance between brake pedal lever and the threaded end of stop lamp switch
0.74 - 1.96 (0.0291 - 0.0772)
Pedal play
3 - 11 (0.12 - 0.43)
Vacuum leakage
[at vacuum of – 66.7 kPa (– 500 mmHg, – 19.69 inHg]
Within 1.3 kPa (10 mmHg, 0.39 inHg) of vacuum for 15 seconds
Vacuum leakage
[at vacuum of – 66.7 kPa (– 500 mmHg, –19.69 inHg)]
Within 3.3 kPa (25 mmHg, 0.98 inHg) of vacuum for 15 seconds
Input rod installation standard dimension
154 - 161 mm (6.06 - 6.34 in)
Brake model
CLZ25VA
Brake pad
Standard thickness (new)
9.5 (0.374)
Repair limit thickness
2.0 (0.079)
SERVICE DATA AND SPECIFICATIONS (SDS)
BR-41
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Rear Disc Brake
INFOID:0000000001716916
Unit: mm (in)
Disc rotor
Standard thickness (new)
24.0 (0.945)
Repair limit thickness
22.0 (0.866)
Runout limit
0.04 (0.0016)
Maximum uneven wear (mea-
sured at 8 positions)
0.02 mm (0.0008 in) or less
Brake model
—
Brake pad
Standard thickness (new)
8.5 (0.335)
Repair limit thickness
2.0 (0.079)
Drum
Standard thickness (new)
9.0 (0.354)
Repair limit inner diameter
8.0 (0.315)
Runout limit
0.07 (0.0028)
Maximum uneven wear (mea-
sured at 8 points)
0.015 (0.00006)
BRC-1
BRAKES
C
D
E
G
H
I
J
K
L
M
SECTION
BRC
A
B
BRC
N
O
P
CONTENTS
BRAKE CONTROL SYSTEM
ABS
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
Work Flow . . . . . . . . . . . . . . . .....
Diagnostic Work Sheet . . . . . . . . . . . ..
INSPECTION AND ADJUSTMENT . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement . .
ADJUSTMENT OF STEERING ANGLE SENSOR
NEUTRAL POSITION . . . . . . . . . . . .
ADJUSTMENT OF STEERING ANGLE SENSOR
NEUTRAL POSITION : Description . . . . . .
CALIBRATION OF DECEL G SENSOR . . . . ...
CALIBRATION OF DECEL G SENSOR : Descrip-
tion . . . . . . . . . . . . . . . . . . ..
CALIBRATION OF DECEL G SENSOR : Special
Repair Requirement . . . . . . . . . . . .
FUNCTION DIAGNOSIS . . . . . . . ..
VDC . . . . . . . . . . . . . . . . .
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ...
TCS . . . . . . . . . . . . . . . . . .
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ...
ABS . . . . . . . . . . . . . . . . ...
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ..
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ...
EBD . . . . . . . . . . . . . . . . ...
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ..
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ...
DIAGNOSIS SYSTEM [ABS ACTUATOR
AND ELECTRIC UNIT (CONTROL UNIT)] . ...
CONSULT-III Function (ABS) . . . . . . . . ..
COMPONENT DIAGNOSIS . . . . . . .
C1101, C1102, C1103, C1104 WHEEL SEN-
SOR-1 . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
Special Repair Requirement . . . . . . . . .
C1105, C1106, C1107, C1108 WHEEL SEN-
SOR-2 . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
Special Repair Requirement . . . . . . . . .
C1109 POWER AND GROUND SYSTEM . .
Description . . . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст