Nissan Tiida C11. Manual — part 115
CHG-38
< COMPONENT DIAGNOSIS >
[K9K]
B TERMINAL CIRCUIT
B TERMINAL CIRCUIT
Description
INFOID:0000000001724509
The terminal “1” (B) circuit supplies power to charge the battery and operate the vehicles electrical system.
Diagnosis Procedure
INFOID:0000000001724510
1.
CHECK TERMINAL “1” CONNECTION
1.
Turn ignition switch OFF.
2.
Verify terminal “1” is clean and tight.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair terminal “1” connection. Confirm repair by performing complete Starting/Charging system
test. Refer to Technical Service Bulletin.
2.
CHECK TERMINAL “1” CIRCUIT
Check voltage between generator connector F2 terminal 1 and
ground.
Is voltage reading as specified?
YES
>> GO TO 3.
NO
>> Check harness for open between generator and fusible
link.
3.
CHECK TERMINAL “1” CONNECTION (VOLTAGE DROP TEST)
1.
Start engine, then engine running at idle and warm.
2.
Check voltage between battery positive terminal and generator
connector F2 terminal 1.
Is the voltage reading as specified?
YES
>> Terminal “1” circuit is normal. Refer to
NO
>> Check harness between battery and generator for high resistance.
(+)
(-)
Voltage
Connector
Terminal
F2
1
Ground
Battery voltage
ALMIA0197ZZ
(+)
(-)
Voltage
Connector
Terminal
F2
1
Battery positive terminal
Less than 0.2V
ALMIA0198ZZ
CHG
L TERMINAL CIRCUIT
CHG-39
< COMPONENT DIAGNOSIS >
[K9K]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
L TERMINAL CIRCUIT
Description
INFOID:0000000001724511
The terminal “2” (L) circuit controls the charge warning lamp. The charge warning lamp illuminates when the
ignition switch is set to ON or START. When the generator is providing sufficient voltage with the engine run-
ning, the charge warning lamp will go off. If the charge warning lamp illuminates with the engine running, a
malfunction is indicated.
Diagnosis Procedure
INFOID:0000000001724512
1.
CHECK CHARGE WARNING LAMP CIRCUIT CONNECTION
Verify generator connector F1 terminal 2 is clean and tight.
Is the connection secure?
YES
>> GO TO 2
NO
>> Repair the connection. Confirm repair by performing complete Starting/Charging system test.
Refer to Technical Service Bulletin.
2.
CHECK CHARGE WARNING LAMP CIRCUIT
1.
Disconnect generator connector F1.
2.
Apply ground to generator harness connector F1 terminal 2 with
the ignition switch in the ON position.
Does the charge lamp illuminate?
YES
>> Check generator function. Refer to
NO
>> GO TO 3
3.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect the generator connector F1 and combination meter
connector M24.
3.
Check continuity between generator harness connector F1 ter-
minal 2 and combination meter harness connector M24 terminal
38.
4.
Check continuity between generator harness connector F1 ter-
minal 2 and ground.
Are the continuity results as specified?
YES
>> Replace the combination meter. Refer to
XX-XX, "*****"
.
NO
>> Repair the harness or connector.
Charge lamp should illuminate
ALMIA0328GB
Terminal
Terminal
Continuity
Connector
Terminal
Connector
Terminal
F1
2
M24
38
Yes
Ter,minal
—
Continuity
Connector
Terminal
F1
2
Ground
No
ALMIA0329GB
CHG-40
< COMPONENT DIAGNOSIS >
[K9K]
S TERMINAL CIRCUIT
S TERMINAL CIRCUIT
Description
INFOID:0000000001724513
The output voltage of the generator is controlled by the IC regulator at terminal “3” (S) detecting the input volt-
age. Terminal “3” circuit detects the battery voltage to adjust the generator output voltage with the IC regulator.
Diagnosis Procedure
INFOID:0000000001724514
1.
CHECK VOLTAGE REGULATOR CIRCUIT CONNECTION
Check to see if connector F1 terminal 3 is clean and tight.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair terminal connection. Confirm repair by performing complete Starting/Charging system test.
Refer to Technical Service Bulletin.
2.
CHECK VOLTAGE REGULATOR CIRCUIT
1.
Disconnect generator harness connector F1.
2.
Turn ignition switch ON.
3.
Check voltage between generator harness connector F1 termi-
nal 3 and ground.
Does battery voltage exist?
YES
>> Refer to
NO
>> Check harness for open between generator and fuse.
3 - ground
Battery voltage
ALMIA0330GB
CHG
CHARGING SYSTEM
CHG-41
< COMPONENT DIAGNOSIS >
[K9K]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CHARGING SYSTEM
Wiring Diagram
INFOID:0000000001724515
AWMWA0023GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст