Nissan Tiida C11. Manual — part 1383
REPAIR FOR COMPONENT PARTS
TM-583
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INSPECTION
Pistons, Retainers and Piston Stem
Check the sliding surfaces for damage or excessive wear. Replace if necessary.
Return Springs
• Check each return spring for damage or deformation. Also mea-
sure free length. Refer to
• Replace springs if deformed or fatigued.
ASSEMBLY
1.
Install D-rings to band servo piston.
2.
Install band servo thrust washer (4), band servo piston (3), OD
servo return spring (2) and spring retainer (1) to band servo pis-
ton stem (5).
3.
Place band servo piston stem (1) on a wooden block, and install
E-ring (2) to band servo piston stem (1) while pressing spring
retainer (3) downward.
SAT138D
SCIA3688E
SCIA7054E
SCIA7056E
TM-584
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
4.
Install O-rings to servo piston retainer
5.
Install band servo piston assembly to servo piston retainer by
pushing it inward.
6.
Install D-ring (1) to OD servo piston (2).
7.
Install O-rings (1), (2) and (3) to OD servo piston retainer (4).
(1): O-ring (small diameter)
(2): O-ring (medium diameter)
(3): O-ring (large diameter)
8.
Install OD servo piston (1) to OD servo piston retainer (2) as
shown.
SCIA3671E
SAT303D
SCIA7053E
SCIA6492J
SCIA7057E
REPAIR FOR COMPONENT PARTS
TM-585
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
9.
Install 2nd servo return spring (2) and band servo piston assem-
bly (3) to transaxle case (1).
10. Install OD servo piston assembly (2) to transaxle case (1).
11. Push in OD servo piston assembly using suitable tool (A) and-
suitable tool (B), and install snap ring (1) to transaxle case using
suitable tool (C).
Final Drive
INFOID:0000000001731447
COMPONENTS
SCIA6310J
SCIA6010J
SCIA7050E
SCIA7184E
TM-586
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
DISASSEMBLY
1.
Remove final gear from differential case.
2.
Remove differential side bearings according to the following procedures.
a.
Set suitable tool (A) on differential case (1), and remove differ-
ential side bearing (RH side) (2) from differential case (1) using
suitable tool (B) and suitable tool (C).
b.
Set suitable tool (A) on differential case (1), and remove differ-
ential side bearing (LH side) (2) from differential case (1) using
suitable tool (B).
3.
Remove pinion mate gear and side gear according to the following procedures.
a.
Drive out lock pin from differential case (1) using Tool (A).
1.
Pinion mate gear thrust washer
2.
Pinion mate gear
3.
Pinion mate shaft
4.
Side gear
5.
Side gear thrust washer
6.
Lock pin
7.
Differential side bearing
8.
Differential case
9.
Final gear
10. Differential side bearing adjusting
shim
SCIA0286J
SCIA7059E
SCIA7060E
Tool number:
KV32101000
SCIA7034E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст