Nissan Tiida C11. Manual — part 794
FUEL TANK
FL-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
9.
Support center of fuel tank (1) with transmission jack (A).
CAUTION:
Securely support the fuel tank with a suitable tool (B).
10. Remove fuel tank mounting straps.
11. Lower transmission jack carefully to remove fuel tank while sup-
porting it by hand. Perform the following works at the same time.
• Pull out vent hose from through hole of vehicle.
• Avoid interference with tank by pulling parking brake cable by
hand.
CAUTION:
Fuel tank may be in an unstable position because of the
shape of fuel tank bottom. Be sure to support tank securely.
INSTALLATION
Installation is in the reverse order of removal.
EVAP Hose
1.
Check connections for damage or foreign material.
2.
Align the mating side connection part with the center of shaft,
and insert connector straight until it clicks.
3.
After connecting, pull out quick connector by hand. Make sure
connections are secure.
Installation of Vent Hose
• Push vent hose into through hole of vehicle.
• Insert vent hose into vent rubber hose, and secure it with clamp.
Installation of Fuel Tank Mounting Strap
• Install them in the proper position by referring to the identification stamp mark “R” and “L1” on the end.
Fuel Filler Hose
• Insert fuel filler hose to the length below.
• When installing clamp, do not allow clamp to contact the bulge (bump) part of the tube.
• Tighten the clamp of filler hose.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1.
Turn ignition switch “ON” (without starting the engine), to check the connections for fuel leaks with the
electric fuel pump applying pressure to the fuel piping.
2.
Start the engine and let it idle to check that there are no fuel leaks at the fuel system connections.
PBIC3792E
PBIC1508E
: 35mm (1.38 in)
Filler hose clamp
: 2.5 N·m (0.26 kg-m, 22 in-lb)
FL-16
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Standard and Limit
INFOID:0000000001722982
FUEL TANK
Unit:
(Imp gal)
Fuel tank capacity
52.0 (11 1/2)
Fuel recommendation
FSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
FSU
A
B
FSU
N
O
P
CONTENTS
FRONT SUSPENSION
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover
. ..
Cautions . . . . . . . . . . . . . . . . ....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
ON-VEHICLE MAINTENANCE . . . . . .
FRONT SUSPENSION ASSEMBLY . . . . ...
On-Vehicle Inspection and Service . . . . . . ...
Wheel Alignment Inspection . . . . . . . . . ..
ON-VEHICLE REPAIR . . . . . . . . ..
FRONT SUSPENSION ASSEMBLY . . . . ...
Component . . . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ...
FRONT SUSPENSION ASSEMBLY . . . . .
Removal and Installation . . . . . . . . . . .
COIL SPRING AND STRUT . . . . . . . ..
Removal and Installation . . . . . . . . . . .
TRANSVERSE LINK . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
STABILIZER BAR . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . ..
COIL SPRING AND STRUT . . . . . . . ..
Disassembly and Assembly . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Alignment (Unladen*) . . . . . . . . ...
Ball Joint . . . . . . . . . . . . . . . . ..
FSU-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001716875
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000001716876
When performing the procedure after removing cowl top cover, cover
the lower end of windshield.
Cautions
INFOID:0000000001716877
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing.
WEIA0178E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст