Nissan Tiida C11. Manual — part 1146
SHOCK ABSORBER
RSU-9
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
• When installing body side bushing (upper), install the projection to
the body side hole securely.
SEIA0645J
RSU-10
< ON-VEHICLE REPAIR >
COIL SPRING
COIL SPRING
Removal and Installation
INFOID:0000000001724579
REMOVAL
1.
Remove rear tires from vehicle using power tool.
2.
Remove wheel sensor from wheel hub and bearing assembly. Refer to
BRC-83, "Removal and Installa-
CAUTION:
Do not pull on wheel sensor harness.
3.
Separate brake tube from wheel cylinder. Refer to
BR-15, "Rear Brake Tube and Hose"
4.
Set jack under rear suspension beam.
5.
Remove shock absorber lower side bolt. Refer to
6.
Gradually lower the jack, and then remove coil spring and rear
spring rubber seat (upper and lower).
INSPECTION AFTER REMOVAL
Check coil spring and spring rubber seat for deformation, cracks, and damage, and replace it if a malfunction
is detected.
INSTALLATION
• Installation is in the reverse order of removal. For tightening torque, refer to
.
• When installing spring, be sure to securely install the spring end
position aligned to flush of rear spring rubber seat (lower) as
shown.
SEIA0146J
SEIA0149J
REAR SUSPENSION BEAM
RSU-11
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION BEAM
Removal and Installation
INFOID:0000000001724580
REMOVAL
1.
Remove rear tires from vehicle using power tool.
2.
Separate parking brake rear cable from rear drum brake and rear suspension beam. Refer to
3.
Remove wheel sensor and wheel sensor harness from wheel hub and bearing assembly and rear suspen-
sion beam. Refer to
BRC-83, "Removal and Installation"
4.
Remove lock plate and separate brake tube from brake hose.
Refer to
BR-15, "Rear Brake Tube and Hose"
.
5.
Remove wheel hub and bearing assembly and back plate. Refer
to
RAX-6, "Removal and Installation"
.
6.
Set jack under rear suspension beam.
7.
Remove coil spring (left/right). Refer to
.
8.
Remove bolts between body and rear suspension beam
bracket. Refer to
.
9.
Gradually lower the jack, and then remove rear suspension
beam from vehicle.
10. Remove the rear suspension beam bracket bolt and nut, and then remove rear suspension beam bracket
from rear suspension beam. Refer to
.
11. Remove brake tube protector from rear suspension beam..
INSPECTION AFTER REMOVAL
Check components for deformation, cracks, and other damage, and replace if necessary.
INSTALLATION
• Installation is in the reverse order of removal. For tightening torque, refer to
.
• Perform final tightening of rear suspension beam and rear suspen-
sion beam bracket (rubber bushing) under unladen conditions with
tires on level ground.
• Refill with new brake fluid and bleed air. Refer to
.
• Check the following after finishing work.
- Parking brake operation (stroke): Refer to
.
- Wheel sensor harness for proper connection: Refer to
MEIA0029E
MEIA0030E
RSU-12
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment (Unladen*)
INFOID:0000000001724581
*: Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.
Wheelarch Height (Unladen*)
INFOID:0000000001724582
Unit: mm (in)
*: Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.
Camber
Degree minute (Decimal degree)
Minimum
– 2
°
01
′
(– 2.02
°
)
Nominal
– 1
°
31
′
(– 1.52
°
)
Maximum
– 1
°
01
′
(– 1.02
°
)
Total toe-in
Distance (A - B)
Minimum
– 1.0 mm (– 0.039 in)
Nominal
3.0 mm (0.118 in)
Maximum
7.0 mm (0.276 in)
Angle (A - B)
Degree minute
(Decimal degree)
Minimum
– 0
°
5
′
(0.08
°
)
Nominal
0
°
13
′
(0.22
°
)
Maximum
0
°
31 (0.52)
Tire size
P195/65R15
Engine model
K9K
HR16DE, MR18DE
Front (Hf)
689 (27.13)
692 (27.24)
Rear (Hr)
689 (27.13)
689 (27.13)
LEIA0085E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст