Nissan Tiida C11. Manual — part 1287
DIFFERENTIAL SIDE OIL SEAL
TM-199
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIFFERENTIAL SIDE OIL SEAL
Differential Side Oil Seal
INFOID:0000000001733162
COMPONENTS
REMOVAL
Refer to figure for differential side oil seals removal procedure.
• Remove differential side oil seals using suitable tool.
CAUTION:
Do not scratch transaxle case and converter housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Drive each differential side oil seal (1) and (2) evenly into the tran-
saxle case side (A) using Tools and converter housing side (B)
using suitable tool to specified dimension “C” or “D”.
Unit: mm (in)
After installing differential side oil seal, check A/T fluid leakage and A/T fluid level. Refer to
1.
A/T
2.
LH differential side oil seal
3.
RH differential side oil seal
SCIA6061J
SCIA4857E
Tool number
: ST35325000
: KV31103000
Engine type
HR16DE
Dimension “C”
0
±
0.5 (0
±
0.020)
Dimension “D”
1.1
±
0.5 (0.043
±
0.020)
SCIA7226E
TM-200
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
SHIFT CONTROL SYSTEM
SHIFT CONTROL SYSTEM
Control Device Removal and Installation
INFOID:0000000001731375
CONTROL DEVICE COMPONENTS
CONTROL CABLE COMPONENTS
1.
Selector lever knob
2.
Knob cover
3.
Lock pin
4.
Overdrive control switch
5.
Knob finisher
6.
Selector button
7.
Selector button return spring
8.
Position indicator plate
9.
Position lamp
10. Dust cover
11.
Bracket
12. Shift lock solenoid and park position
switch assembly
13. A/T device harness connector
14. Plate
15. Control device assembly
WCIA0638E
SHIFT CONTROL SYSTEM
TM-201
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL
CAUTION:
Make sure that parking brake is applied before removal/installation.
1.
Place the selector lever in the “N” position.
2.
Remove the center console assembly. Refer to
IP-11, "Removal and Installation"
.
3.
Disconnect the A/T device harness connector (1).
4.
Remove the key interlock cable from the control device assem-
bly. Refer to
TM-206, "Removal and Installation"
.
5.
Remove the bolts (A) from the control device assembly (1).
6.
Remove exhaust front tube, center muffler and heat plates.
Refer to
EX-5, "Removal and Installation"
1.
Selector lever knob
2.
Control device assembly
3.
Lock plate
4.
Floor panel
5.
Control cable
6.
Bracket
7.
Lock plate
8.
Lock nut
9.
A/T assembly
10. Bracket
11.
Bracket
WCIA0640E
SCIA6965E
WCIA0609E
TM-202
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
SHIFT CONTROL SYSTEM
7.
Remove the plate (1) from the control device assembly.
: Vehicle front
8.
Remove the lock plate (1) from the control cable (2).
: Vehicle front
9.
Remove the control cable (2) from the control device assembly.
10. Insert flat-bladed screwdrivers at points (A) and (B) as shown,
and press both tabs (E) and (F) at the front (C) and rear (D)
slightly toward the center of the control device assembly to
remove the control device assembly from the underside of the
vehicle.
: Vehicle front
INSTALLATION
Installation is in the reverse order of removal.
SCIA6967E
SCIA6968E
SCIA6970E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст