Nissan Tiida C11. Manual — part 764
EXL-54
< COMPONENT DIAGNOSIS >
TURN SIGNAL LAMP CIRCUIT
Does continuity exist?
YES
>> Replace the front combination lamp, side turn signal lamp or the rear combination lamp.
NO
>> Repair the harnesses or connectors.
Front LH
E29 (halogen headlamps)
5
Ground
Yes
E25 (xenon headlamps)
2
Rear LH
B80
1
Side LH
E56
2
Front RH
E30 (halogen headlamps)
5
E26 (xenon headlamps)
2
Rear RH
B59
1
Side RH
E57
2
LIGHT & RAIN SENSOR
EXL-55
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LIGHT & RAIN SENSOR
Description
INFOID:0000000001523274
The light and rain sensor converts outside light (lux) to voltage and transmits the light and rain sensor signal to
the BCM.
Component Function Check
INFOID:0000000001523275
1.
CHECK LIGHT AND RAIN SENSOR SIGNAL BY CONSULT-III
CONSULT-III
1.
Turn the ignition switch ON.
2.
Select "LIT-SEN FAIL" of BCM (HEAD LAMP) DATA MONITOR item.
3.
Check the monitor status.
Is the item status OK?
YES
>> Light and rain sensor is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000001523276
1.
CHECK LIGHT AND RAIN SENSOR POWER SUPPLY
1.
Turn the ignition switch ON.
2.
Check the voltage between the light and rain sensor harness connector and ground.
Is the voltage as specified?
YES
>> GO TO 2
NO
>> GO TO 4
2.
CHECK LIGHT AND RAIN SENSOR GROUND CIRCUIT
Check the voltage between the light and rain sensor harness connector R11 terminal 3 and ground.
Is the voltage as specified?
YES
>> GO TO 3
NO
>> Repair the harness or connector.
3.
CHECK LIGHT AND RAIN SENSOR SIGNAL FOR OPEN OR SHORT CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect the light and rain sensor connector R11 and BCM connector M19.
3.
Check continuity between the light and rain sensor harness connector R11 (A) terminal 2 and the BCM
harness connector M19 (B) terminal 63.
Monitor item
Condition
LIT-SEN FAIL
OK
NOT OK
(+)
(
−
)
Voltage
Connector
Terminal
R11
1
Ground
12V
(+)
(
−
)
Voltage
Connector
Terminal
R11
3
Ground
Less than 0.2 V
EXL-56
< COMPONENT DIAGNOSIS >
LIGHT & RAIN SENSOR
4.
Check continuity between the light and rain sensor harness connector R11 (A) terminal 2 and ground.
Are the continuity check results as specified?
YES
>> Replace the light and rain sensor.
NO
>> Repair harness or connector.
4.
CHECK LIGHT AND RAIN SENSOR POWER SUPPLY FOR OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect the light and rain sensor connector R11 and BCM connector M20.
3.
Check continuity between the light and rain sensor harness connector R11 (A) terminal 1 and the BCM
harness connector M20 (B) terminal 73.
jAre continuity check results as specified?
YES
>> Replace the BCM.
NO
>> Repair the harnesses or connectors.
A
B
Continuity
Connector
Terminal
Connector
Terminal
R11
2
M19
63
Yes
A
—
Continuity
Connector
Terminal
R11
2
Ground
No
A
B
Continuity
Connector
Terminal
Connector
Terminal
R11
1
M20
73
Yes
HEADLAMP AIMER SWITCH
EXL-57
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HEADLAMP AIMER SWITCH
Description
INFOID:0000000001532097
The manual headlamp aiming system uses a headlamp aimer switch to adjust the axis of the headlamp aiming
motor. The headlamp aimer switch has four settings, each with a different resistance value. The headlamp
aiming motor adjusts to the proper axis based off the position of the headlamp aiming switch.
Diagnosis Procedure
INFOID:0000000001532099
1.
CHECK HEADLAMP AIMER SWITCH SIGNAL FOR OPEN OR SHORT CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect headlamp aimer switch connector M56, headlamp aimer motor LH connector E36 and head-
lamp aimer motor RH connector E37.
3.
Check continuity between the headlamp aimer switch connector M56 (A) terminal 1 and headlamp aimer
motor LH E37 and RH E36 (B) terminal 2.
4.
Check continuity between the headlamp aimer switch connector M56 (A) terminal 1 and ground.
Are the continuity test results as specified?
YES
>> GO TO 2
NO
>> Repair the harness or connector.
2.
CHECK HEADLAMP AIMER SWITCH
1.
Check continuity between the headlamp aimer switch terminals 1 and 2 in each switch position.
Are the continuity check results as specified?
YES
>> GO TO 3
NO
>> Replace the headlamp aimer switch.
3.
CHECK HEADLAMP AIMER SWITCH GROUND CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect headlamp aimer switch connector M56.
3.
Check continuity between headlamp aimer switch connector M56 terminal 2 and ground.
Is continuity as specified?
YES
>> Inspect headlamp aimer motors.
NO
>> Repair harness or connector.
A
B
Continuity
Connector
Terminal
M56
1
Ground
Yes
A
—
Continuity
Connector
Terminal
M56
1
Ground
No
Component
Terminal
Switch Position
Continuity
Headlamp
aimer
switch
1
2
0
604 ohms
1
324 ohms
2
191 ohms
3
130 ohms
Connector
Terminal
—
Continuity
M56
2
Ground
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст