Nissan Tiida C11. Manual — part 1464
BCM (BODY CONTROL MODULE)
WW-51
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Reference Value
INFOID:0000000001366631
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
.
PHYSICAL VALUES
Monitor Item
Condition
Value/Status
FR WASHER SW
Front washer switch OFF
OFF
Front washer switch ON
ON
FR WIPER LOW
Front wiper switch OFF
OFF
Front wiper switch LO
ON
FR WIPER HI
Front wiper switch OFF
OFF
Front wiper switch HI
ON
FR WIPER INT
Front wiper switch OFF
OFF
Front wiper switch INT
ON
FR WIPER STOP
Any position other than front wiper stop position
OFF
Front wiper stop position
ON
H/L SW POS
Lighting switch OFF
OFF
Lighting switch 2ND
ON
LIGHT SW 1ST
Lighting switch OFF
OFF
Lighting switch 2ND
ON
HI BEAM SW
Lighting switch OFF
OFF
Lighting switch HI
ON
H/L WASH SW
NOTE:
The item is indicated, but not monitored
OFF
IGN ON SW
Ignition switch OFF or ACC
OFF
Ignition switch ON
ON
IGN SW CAN
Ignition switch OFF or ACC
OFF
Ignition switch ON
ON
INT VOLUME
Wiper intermittent dial is in a dial position 1 - 7
1 - 7
RR WASHER SW
Rear washer switch OFF
OFF
Rear washer switch ON
ON
RR WIPER INT
Rear wiper switch OFF
OFF
Rear wiper switch INT
ON
RR WIPER ON
Rear wiper switch OFF
OFF
Rear wiper switch ON
ON
RR WIPER STOP
Rear wiper stop position
OFF
Other than rear wiper stop position
ON
VEHICLE SPEED
While driving
Equivalent to speedometer reading
WW-52
< ECU DIAGNOSIS >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)
Reference Value
INFOID:0000000001366636
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
Refer to xxx.
PHYSICAL VALUES
Refer to xxx.
Fail Safe
INFOID:0000000001366638
CAN communication control
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If no CAN communication is available with BCM
Front wiper control
IPDM E/R detects the front wiper stop position with the front wiper auto stop signal.
When the front wiper auto stop signal is in the conditions listed below, IPDM E/R repeats a front wiper 10 sec-
onds operation and 20 seconds stop five times.
Monitor Item
Condition
Value/Status
HL WASHER REQ
Ignition switch ON, and low
beam headlamp is ON
Front washer switch OFF
Off
Front washer switch ON
(When headlamp washer is operat-
ing)
On
FR WIP REQ
Ignition switch ON
Front wiper switch OFF
STOP
Front wiper switch INT
1LOW
Front wiper switch LO
Low
Front wiper switch HI
Hi
WIP AUTO STOP
Ignition switch ON
Front wiper stop position
STOP P
Any position other than front wiper
stop position
ACT P
WIP PROT
Ignition switch ON
Front wiper operates normally
Off
Front wiper stops at fail-safe oper-
ation
BLOCK
IGN RLY
Ignition switch OFF or ACC
Off
Ignition switch ON
On
IGN ON SW
Ignition switch OFF or ACC
Off
Ignition switch ON
On
Control part
Fail-safe in operation
Front wiper
• The status just before activation of fail-safe control is maintained until the ignition
switch is turned OFF while the front wiper is operating at LO or HI speed.
• The front wiper is operated at LO speed until the ignition switch is turned OFF if the
fail-safe control is activated while the front wiper is set in the INT mode and the front
wiper motor is operating.
Headlamp washer
Headlamp washer relay OFF
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
WW-53
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
Ignition switch
Front wiper switch
Front wiper auto stop signal
ON
OFF
The front wiper auto stop signal (stop posi-
tion) cannot be input for 10 seconds.
ON
The front wiper auto stop signal does not
change for 10 seconds.
WW-54
< SYMPTOM DIAGNOSIS >
WIPER AND WASHER SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
WIPER AND WASHER SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000001366640
CAUTION:
Perform the self-diagnosis with CONSULT-III before performing the diagnosis by symptom. Perform
the diagnosis by DTC if DTC is detected.
Symptom
Probable malfunction location
Inspection item
Front wiper does not
operate.
HI only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper motor (HI) circuit
Refer to
.
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
"FR WIP REQ"
LO and INT
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper motor (LO) circuit
Refer to
.
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
"FR WIP REQ"
INT only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
"FR WIP REQ"
HI, LO, and INT
SYMPTOM DIAGNOSIS
“FRONT WIPER DOES NOT OPERATE”
Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст