Nissan Tiida C11. Manual — part 1427
VTL-44
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
BLOWER FAN RESISTOR
BLOWER FAN RESISTOR
Removal and Installation
INFOID:0000000001696536
REMOVAL
1.
Remove the instrument lower finisher and instrument lower cover (LH) for LHD only. Refer to
2.
Remove the glove box assembly and instrument lower cover (RH) for RHD only. Refer to
3.
Remove the console side cover. Refer to
.
4.
Remove the brake pedal assembly for LHD only. Refer to
BR-12, "Removal and Installation"
.
5.
Disconnect the blower fan resistor connector.
6.
Remove the blower fan resistor screws (A), then remove the
blower fan resistor (1).
INSTALLATION
Installation is in the reverse order of removal.
SJIA0656E
INTAKE DOOR
VTL-45
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
INTAKE DOOR
Intake Door Cable Adjustment
INFOID:0000000001696537
1.
Remove the instrument lower finisher and instrument lower cover (LH) for LHD only. Refer to
2.
Remove the glove box assembly and instrument lower cover (RH) for RHD only. Refer to
3.
Remove outer cable of intake door cable (1) from clamp (A).
4.
Set intake door lever to REC position.
5.
Push intake door link (2) in the direction shown by the arrow,
and then carefully pull outer cable to controller side, and install
clamp (A).
6.
Operate intake door lever to insure that inner cable moves
smoothly.
CAUTION:
When clamping the outer cable, do not move the inner
cable.
SJIA0650E
VTL-46
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
AIR MIX DOOR
AIR MIX DOOR
Air Mix Door Cable Adjustment
INFOID:0000000001696538
1.
Remove steering member. Refer to
ST-9, "Removal and Installation"
.
2.
Remove outer cable of air mix door cable (1) from clamp (A).
3.
Set temperature control dial to full cold position.
4.
Push air mix door lever (2) in the direction shown by arrow, and
then carefully pull outer cable toward controller side, and install
clamp (A).
5.
Operate temperature control dial to insure that inner cable
moves smoothly.
CAUTION:
When clamping the outer cable, do not move the inner
cable.
SJIA1150E
MODE DOOR
VTL-47
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
MODE DOOR
Mode Door Cable Adjustment
INFOID:0000000001696539
1.
Remove the glove box assembly and instrument lower cover (RH) for LHD only. Refer to
2.
Remove the instrument lower finisher and instrument lower cover (LH) for RHD only. Refer to
3.
Remove outer cable of mode door cable (1) from clamp (A).
4.
Set mode control dial to VENT position.
5.
Push main link (2) in the direction shown by the arrow, and then
carefully pull outer cable to controller side, and install clamp (A).
6.
Operate mode control dial to insure that inner cable moves
smoothly.
CAUTION:
When clamping the outer cable, do not move the inner
cable.
7.
Turn mode control dial to each position.
8.
Confirm that discharge air comes out according to the air distribution table. Refer to
.
SJIA0654E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст