Nissan Tiida C11. Manual — part 1315
ASSEMBLY
TM-311
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Adjust reverse clutch end play “T
2
”.
• Select proper thickness of thrust washer so that reverse clutch end play is within specifications.
Assembly (3)
INFOID:0000000001731000
1.
Remove reverse clutch assembly.
2.
Install needle bearing on input shaft assembly (high clutch
drum).
CAUTION:
Be careful with the direction of needle bearing.
3.
Install reverse clutch assembly.
CAUTION:
Align teeth of reverse clutch drive plates before installing.
4.
Install anchor end pin (2) and lock nut (1) on transaxle case.
5.
Place brake band on outside of reverse clutch drum.
6.
Tighten anchor end pin just enough so that brake band is evenly
fitted on reverse clutch drum.
7.
Install bearing race selected in total end play adjustment step on
oil pump cover.
8.
Install thrust washer selected in reverse clutch end play adjust-
ment step on oil pump cover.
9.
Install O-ring to oil pump assembly.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
T
2
= N – Q
Reverse clutch end play:
TM-324, "Reverse Clutch End Play"
SAT387D
SCIA6037J
SAT038D
SCIA3629E
TM-312
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
ASSEMBLY
10. Install oil pump assembly (1) on transaxle case.
11. Tighten oil pump bolts to the specified torque.
12. Install O-ring to input shaft assembly (high clutch drum).
13. Adjust brake band.
a.
Tighten anchor end pin to the specified torque.
b.
Back off anchor end pin two and a half turns.
c.
Tighten lock nut while holding anchor end pin.
SCIA6036J
SCIA4928E
Anchor end pin
: 4.9 N·m (0.50 kg-m, 43 in-lb)
SAT394D
SAT395D
SAT396D
ASSEMBLY
TM-313
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
14. Apply compressed air into oil holes of transaxle case and check
operation of brake band.
15. Select proper thickness of differential side bearing adjusting shim using the following procedures.
• Measure differential side bearing end play, and calculate the adjusting shim thickness so that the end
play is within the specifications.
a.
Place a straightedge (A) onto transaxle case (1), and measure
the depth “T” of transaxle case (1) to the mating surface for dif-
ferential side bearing using depth gauge (B).
• Measure the depth “T” in at least two places, and take the
average.
b.
Install final drive assembly onto converter housing (1).
c.
Place a straightedge (A) onto differential case (2), and measure
the height “U” to the end of converter housing (1) using depth
gauge (B).
• Measure the height “U” in at least two places, and take the
average.
d.
Place a straightedge (A) onto differential case (1), and measure
the height “V” to the end of differential side bearing outer race
using depth gauge (B).
• Measure the height “V” in at least two places, and take the
average.
e.
Select proper thickness of differential side bearing adjusting
shim.
SAT397D
Differential side bearing end play:
.
T = (Measurement) - (Straightedge thickness)
SCIA7114E
SCIA7115E
Proper shim thickness
= T - U + V + [0 - 0.15 mm (0 - 0.0059 in)]
*
(
*
: differential side bearing end play)
SCIA7116E
TM-314
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
ASSEMBLY
16. Install differential side bearing adjusting shim selected in differ-
ential side bearing end play adjustment step on transaxle case.
17. Install final drive assembly (1) on transaxle case.
18. Install differential lubricant tube and clips on converter housing.
19. Tighten differential lubricant tube fitting bolts to the specified
torque.
20. Install O-ring (1) on differential oil port of transaxle case as
shown.
21. Apply locking sealant (loctite #518) to transaxle case as shown.
: Inside of transaxle case
CAUTION:
SCIA4938E
SCIA6034J
SCIA3284E
SCIA5918J
“A”
: 3 - 5 mm (0.12 - 0.20 in)
“B”
: 8 mm (0.31 in) R
“C”
: 1.5 mm (0.059 in) dia.
“D”
: 4 mm (0.16 in)
SCIA7089E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст