Nissan Frontier D40. Manual — part 840
ENGINE MAINTENANCE (VQ40DE)
MA-41
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
3.
Screw on the oil filter manually until it touches the installation
surface, then tighten it by 2/3 turn as shown. Or tighten to speci-
fication.
4.
Refill engine with new engine oil. Refer to
5.
Inspect the engine for oil leaks. Refer to
MA-40, "OIL FILTER : Removal and Installation"
6.
Install the engine front undercover using power tool.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
MA-38, "ENGINE OIL : Inspection"
.
2.
Start the engine and check for engine oil leaks.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level and add engine oil as required.
SPARK PLUG
SPARK PLUG : Exploded View
INFOID:0000000005272760
SPARK PLUG : Removal and Installation
INFOID:0000000005272761
REMOVAL
1.
Remove the engine room cover. Refer to
EM-138, "Removal and Installation"
2.
Remove the ignition coil. Refer to
EM-154, "Removal and Installation"
.
Oil filter
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
SMA702C
1.
Ignition coil
2.
Spark plug
PBIC2901E
MA-42
< ON-VEHICLE MAINTENANCE >
ENGINE MAINTENANCE (VQ40DE)
3.
Remove the spark plug using a suitable tool.
CAUTION:
Do not drop or shock it.
INSPECTION AFTER REMOVAL
• Do not use a wire brush for cleaning.
• If the spark plug tip is covered with carbon, spark plug cleaner may be used.
• Checking and adjusting spark plug gap is not required between
change intervals.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not drop or shock the spark plug.
EVAP VAPOR LINES
EVAP VAPOR LINES : Checking EVAP Vapor Line
INFOID:0000000005272762
1.
Visually inspect EVAP vapor lines for improper attachment, cracks, damage, loose connections, chafing
or deterioration.
2.
Inspect vacuum relief valve of fuel tank filler cap for clogging and sticking.
SEM294A
SMA773C
Cleaner air pressure
: Less than 588 kPa (5.9 bar, 6 kg/cm
2
, 85 psi)
Cleaning time
: Less than 20 seconds
SMA806CA
Make
NGK
Standard type
DILFR5A-11
Gap (nominal)
1.1 mm (0.043 in)
ENGINE MAINTENANCE (VQ40DE)
MA-43
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
EC-956, "How to Detect Fuel Vapor Leakage"
.
MA-44
< ON-VEHICLE MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
CHASSIS AND BODY MAINTENANCE
IN-CABIN MICROFILTER
IN-CABIN MICROFILTER : Removal and Installation
INFOID:0000000005272763
REPLACEMENT PROCEDURE
1.
Open the lower glove box and press in on the sides so that it will
open completely allowing it to hang by the cord.
2.
Depress the tab and remove the in-cabin microfilter cover as
shown.
3.
Remove the in-cabin microfilters from the heater and cooling unit housing.
4.
Insert the first new in-cabin microfilter into the heater and cool-
ing unit housing and slide it over to the right. Insert the second
new in-cabin microfilter into the heater and cooling unit housing
as shown.
NOTE:
The in-cabin microfilters are marked with air flow arrows. The
end of the microfilter with the arrow should face the rear of the
vehicle. The arrows should point downward.
5.
Install the in-cabin microfilter cover, make sure the tab is locked
in place as shown.
6.
Close the lower glove box completely.
EXHAUST SYSTEM
WLIA0023E
ALIIA0359ZZ
ALIIA0360ZZ
ALIIA0359ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст