Nissan Frontier D40. Manual — part 947
SB-4
< ON-VEHICLE REPAIR >
FRONT SEAT BELT
ON-VEHICLE REPAIR
FRONT SEAT BELT
Exploded View
INFOID:0000000005272884
King Cab Models
WHIA0345E
1.
Center pillar
2.
Seat belt height adjuster
3.
Seat belt retractor and belt assembly RH
4.
Seat belt pre-tensioner connector
5.
Seat belt tension sensor
connector
6.
Seat belt lower anchor RH (seat belt tension
sensor
7.
Anchor cover RH
8.
Anchor cover LH
9.
Seat belt lower anchor LH
10. Seat belt retractor and belt assembly
LH
11.
D-ring anchor bolt cover
12. D-ring anchor
A.
Height adjuster anchor bolt
B.
Retractor bolt upper
C.
Retractor anchor bolt
D.
Seat belt lower anchor bolt
E.
D-ring anchor bolt
Vehicle front
FRONT SEAT BELT
SB-5
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
Crew Cab Models
Removal and Installation
INFOID:0000000005272885
REMOVAL OF SEAT BELT RETRACTOR - KING CAB
CAUTION:
• Before servicing SRS, turn the ignition switch off, disconnect both battery terminals and wait at least
three minutes.
1.
Disconnect both the negative and positive battery terminals, then wait at least three minutes.
2.
Remove the rear door finishers. Refer to
INT-14, "Removal and Installation"
.
3.
Remove the retractor anchor bolt, retractor bolt upper, then remove the retractor and belt assembly.
• On RH side, disconnect the seat belt tension sensor.
WHIA0344E
1.
Center pillar upper finisher
2.
D-ring anchor
3.
D-ring anchor bolt cover
4.
Seat belt retractor and belt assembly
RH
5.
Seat belt lower anchor RH
(seat belt tension sensor)
6.
Seat belt tension sensor connector
7.
Anchor cover RH
8.
Anchor cover LH
9.
Seat belt lower anchor LH
10. Center pillar lower finisher
11.
Seat belt pre-tensioner
connector
12. Seat belt retractor and belt assembly LH
13. Center pillar
14. Seat belt height adjuster
A.
Height adjuster anchor bolt
B.
D-ring anchor bolt
C.
Seat belt lower anchor bolt D.
Retractor anchor bolt
E.
Retractor bolt upper
Vehicle front
SB-6
< ON-VEHICLE REPAIR >
FRONT SEAT BELT
4.
Disconnect the seat belt pre-tensioner harness connector.
CAUTION:
• For installing/removing seat belt pre-tensioner connector,
insert a thin screwdriver wrapped in tape into the notch,
lift the lock and remove the connector.
• Install the connector with the lock raised, and push the
lock into the connector.
INSTALLATION OF SEAT BELT RETRACTOR - KING CAB
CAUTION:
Hold belt tension sensor harness away from being caught or twisted during installation.
Installation is in the reverse order of removal.
• Install the seat belt retractor upper bolt first.
• Ensure that seat belt height adjuster is locked in the lowest position during installation.
REMOVAL OF SEAT BELT RETRACTOR - CREW CAB
CAUTION:
• Before servicing SRS, turn the ignition switch off, disconnect both battery terminals and wait at least
three minutes.
1.
Disconnect both the negative and positive battery terminals, then wait at least three minutes.
2.
Remove the center pillar upper/lower finishers. Refer to
INT-18, "Removal and Installation"
.
3.
Remove the seat belt retractor and belt bolts and assembly.
• On RH side, disconnect the seat belt tension sensor.
4.
Disconnect the seat belt pre-tensioner harness connector.
CAUTION:
• For installing/removing seat belt pre-tensioner connector,
insert a thin screwdriver wrapped in tape into the notch, lift
the lock and remove the connector.
• Install the connector with the lock raised, and push the lock
into the connector.
INSTALLATION OF SEAT BELT RETRACTOR - CREW CAB
CAUTION:
Hold belt tension sensor harness away from being caught or twisted during installation.
Installation is in the reverse order of removal.
• Install the seat belt retractor and belt assembly upper bolt first.
• Ensure that seat belt height adjuster is locked in the lowest position during installation.
REMOVAL OF SEAT BELT BUCKLE
1.
Remove the front seat. Refer to
SE-28, "Removal and Installation"
PHIA0341E
PHIA0341E
FRONT SEAT BELT
SB-7
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
2.
Remove screw and seat cushion inner finisher.
3.
Remove the anchor bolt and buckle.
4.
Disconnect the buckle switch connector from the seat connector.
INSTALLATION OF SEAT BELT BUCKLE
Installation is in the reverse order of removal.
Seat Belt Inspection
INFOID:0000000005272886
AFTER A COLLISION
WARNING:
Inspect all seat belt assemblies including retractors and attaching hardware after any collision.
NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the col-
lision was minor and the belts show no damage and continue to operate properly. Failure to do so
could result in serious personal injury in an accident. Seat belt assemblies not in use during a colli-
sion should also be replaced if either damage or improper operation is noted. Seat belt pre-tensioners
should be replaced even if the seat belts are not in use during a frontal collision in which the air bags
are deployed.
Replace any seat belt assembly (including anchor bolts) if:
• The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and
buckles show no damage and continue to operate properly).
• The seat belt was damaged in an accident. (i.e. torn webbing, bent retractor or guide).
• The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage
or distortion and repair as necessary before installing a new seat belt assembly.
• Anchor bolts are deformed or worn out.
• The seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision in
which the air bags are deployed.
PRELIMINARY CHECKS
1.
Check the seat belt warning lamp/chime for proper operation as follows:
a.
Switch ignition ON. The seat belt warning lamp should illuminate. Also, the seat belt warning chime should
sound for about seven seconds.
b.
Fasten driver's seat belt. The seat belt warning lamp should go out and the chime (if sounding) should
stop.
2.
If the air bag warning lamp is blinking, conduct self-diagnosis using CONSULT-III, and air bag warning
lamp. Refer to
.
3.
Check that the seat belt retractor, seat belt anchor and buckle bolts are securely attached.
4.
Check the shoulder seat belt guide and shoulder belt height adjuster for front seats. Ensure guide swivels
freely and that belt lays flat and does not bind in guide. Ensure height adjuster operates properly and
holds securely.
5.
Check retractor operation:
a.
Fully extend the seat belt webbing and check for twists, tears or other damage.
b.
Allow the seat belt to retract. Ensure that belt returns smoothly and completely into the retractor. If the
seat belt does not return smoothly, wipe the inside of the loops with a clean paper cloth, because dirt built
up in the loops of the upper anchors can cause the seat belts to retract slowly.
c.
Fasten the seat belt. Check the seat belt returns smoothly and completely to the retractor. If the belt does
not return smoothly, the cause may be an accumulation of dust or dirt. Use the “SEAT BELT TAPE SET”
and perform the following steps.
WHIA0128E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст