Nissan Frontier D40. Manual — part 1143
WCS-64
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
DTC Inspection Priority Chart
INFOID:0000000005548412
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
DTC Index
INFOID:0000000005548413
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF
→
ON again.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→
2
→
3...38
→
39 after returning to the normal condition whenever ignition switch OFF
→
ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF
→
ON after returning to the normal condition if the malfunction is detected again.
Display contents of CONSULT
Fail-safe
Cancellation
U1000: CAN COMM CIRCUIT
Inhibit engine cranking
When the BCM re-establishes communication with the other mod-
ules.
Priority
DTC
1
• U1000: CAN COMM CIRCUIT
2
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
3
• C1729: VHCL SPEED SIG ERR
• C1735: IGNITION SIGNAL
4
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL
CONSULT display
Fail-safe
Tire pressure
monitor warning
lamp ON
Reference page
No DTC is detected.
further testing
may be required.
—
—
—
U1000: CAN COMM CIRCUIT
—
—
WCS
BCM (BODY CONTROL MODULE)
WCS-65
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2190: NATS ANTTENA AMP
—
—
B2191: DIFFERENCE OF KEY
—
—
B2192: ID DISCORD BCM-ECM
—
—
B2193: CHAIN OF BCM-ECM
—
—
C1708: [NO DATA] FL
—
—
C1709: [NO DATA] FR
—
—
C1710: [NO DATA] RR
—
—
C1711: [NO DATA] RL
—
—
C1712: [CHECKSUM ERR] FL
—
—
C1713: [CHECKSUM ERR] FR
—
—
C1714: [CHECKSUM ERR] RR
—
—
C1715: [CHECKSUM ERR] RL
—
—
C1716: [PRESSDATA ERR] FL
—
—
C1717: [PRESSDATA ERR] FR
—
—
C1718: [PRESSDATA ERR] RR
—
—
C1719: [PRESSDATA ERR] RL
—
—
C1720: [CODE ERR] FL
—
—
C1721: [CODE ERR] FR
—
—
C1722: [CODE ERR] RR
—
—
C1723: [CODE ERR] RL
—
—
C1724: [BATT VOLT LOW] FL
—
—
C1725: [BATT VOLT LOW] FR
—
—
C1726: [BATT VOLT LOW] RR
—
—
C1727: [BATT VOLT LOW] RL
—
—
C1729: VHCL SPEED SIG ERR
—
—
C1735: IGNITION SIGNAL
—
—
—
CONSULT display
Fail-safe
Tire pressure
monitor warning
lamp ON
Reference page
WCS-66
< SYMPTOM DIAGNOSIS >
THE LIGHT REMINDER WARNING DOES NOT SOUND
SYMPTOM DIAGNOSIS
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description
INFOID:0000000005274849
Light reminder warning does not sound even though headlamp is illuminated.
Diagnosis Procedure
INFOID:0000000005274850
1.
CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION
Check that the headlamps operate normally by operating the combination switch (lighting switch).
Do they operate normally?
YES
>> GO TO 2
NO
>> Refer to
2.
CHECK FRONT DOOR SWITCH LH SIGNAL CIRCUIT
Perform inspection of the front door switch LH signal circuit. Refer to
DLK-29, "CREW CAB : Diagnosis Proce-
or
DLK-29, "CREW CAB : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair harness or connector.
3.
CHECK FRONT DOOR SWITCH LH
Perform a unit inspection for the front door switch LH. Refer to
or
DLK-27, "KING CAB : Component Function Check"
Is the inspection result normal?
YES
BCS-54, "Removal and Installation"
NO
>> Replace the front door switch LH.
WCS
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND
WCS-67
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT
SOUND
Description
INFOID:0000000005274851
• Seat belt warning does not sound even though driver seat belt is not fastened.
• Seat belt warning sounds even though driver seat belt is fastened.
Diagnosis Procedure
INFOID:0000000005274852
1.
CHECK WARNING CHIME OPERATION
1.
With key removed from key switch and the front door LH open, turn lighting switch to 1st or 2nd position.
2.
Return lighting switch to off position, and insert key into key switch.
Does warning chime sound for both steps?
YES
>> GO TO 2
NO
>> Replace combination meter. Refer to
MWI-95, "Removal and Installation"
2.
CHECK SEAT BELT WARNING LAMP
1.
Turn ignition switch ON.
2.
Check the operation of the seat belt warning lamp in the combination meter.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-54, "Removal and Installation"
NO
>> GO TO 3
3.
CHECK SEAT BELT BUCKLE SWITCH CIRCUIT
Perform inspection of the seat belt buckle switch circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair harness or connector.
4.
CHECK SEAT BELT BUCKLE SWITCH UNIT
Perform a unit inspection for the seat belt buckle switch. Refer to
WCS-20, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
MWI-95, "Removal and Installation"
.
NO
>> Replace the seat belt buckle switch LH.
Seat belt fastened
: OFF
Seat belt not fastened
: ON
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст