Nissan Frontier D40. Manual — part 87
BRC-46
< COMPONENT DIAGNOSIS >
[TYPE 1]
ABS WARNING LAMP
ABS WARNING LAMP
Description
INFOID:0000000005275085
×
: ON –: OFF
Component Function Check
INFOID:0000000005275086
1.
CHECK ABS WARNING LAMP OPERATION
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Go to diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000005275087
1.
CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check items displayed by self-diagnosis.
2.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-71, "Removal and Installa-
.
NO
>> Replace combination meter. Refer to
MWI-95, "Removal and Installation"
Condition
ABS warning lamp
Ignition switch OFF
–
For 2 seconds after turning ON ignition switch
×
2 seconds later after turning ON ignition switch
–
ABS function is malfunctioning.
×
EBD function is malfunctioning.
×
BRAKE WARNING LAMP
BRC-47
< COMPONENT DIAGNOSIS >
[TYPE 1]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
BRAKE WARNING LAMP
Description
INFOID:0000000005275088
×
: ON –: OFF
NOTE:
• 1: Brake warning lamp will turn on in case of parking brake operation (when switch is ON) or of brake fluid level switch operation
(when brake fluid is insufficient).
• 2: After starting engine, brake warning lamp is turned off.
Component Function Check
INFOID:0000000005275089
1.
BRAKE WARNING LAMP OPERATION CHECK
Check that the lamp illuminates after the ignition switch is turned ON, and turns OFF after the engine is
started.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Go to diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000005275090
1.
CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check items displayed by self-diagnosis.
2.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-71, "Removal and Installa-
.
NO
>> Replace combination meter. Refer to
MWI-95, "Removal and Installation"
Condition
Brake warning lamp (Note 1)
Ignition switch OFF
–
Ignition switch ON
×
(Note 2)
EBD function is malfunctioning.
×
BRC-48
< ECU DIAGNOSIS >
[TYPE 1]
APPLICATION NOTICE
ECU DIAGNOSIS
APPLICATION NOTICE
Application Notice
INFOID:0000000005548018
Service information
Remarks
TYPE 1
ABS
TYPE 2
VDC/TCS/ABS
TYPE 3
HILL DESCENT CONTROL/HILL START ASSIST/VDC/TCS/ABS
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-49
< ECU DIAGNOSIS >
[TYPE 1]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Reference Value
INFOID:0000000005275092
VALUES ON THE DIAGNOSIS TOOL
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the
event the output circuit (harness) is open or short-circuited.
CONSULT-III MONITOR ITEM
Monitor item
Display content
Data monitor
Condition
Reference value in
normal operation
FR LH SENSOR
Wheel speed
0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(
±
10% or less)
Vehicle running
(Note 1)
FR RH SENSOR
Wheel speed
0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(
±
10% or less)
Vehicle running
(Note 1)
RR LH SENSOR
Wheel speed
0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(
±
10% or less)
Vehicle running
(Note 1)
RR RH SENSOR
Wheel speed
0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(
±
10% or less)
Vehicle running
(Note 1)
FR RH IN SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
Off
FR RH OUT SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
Off
FR LH IN SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
Off
FR LH OUT SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
Off
REAR IN SOL
Operation status of each solenoid valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)
Off
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст