Nissan Frontier D40. Manual — part 179

CL-2

Clutch Cover . . . . . . . . . . . . . . ...

25

Clutch Pedal . . . . . . . . . . . . . . .

25

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

CL-3

< SYMPTOM DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

CL

N

O

P

SYMPTOM DIAGNOSIS

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NVH Troubleshooting Chart

INFOID:0000000005276123

Use the chart below to help you find the cause of the symptom. The numbers indicate the order of the inspec-
tion. If necessary, repair or replace these parts.

CLUTCH

Reference page

CL-8

CL-9

BR

-4

9

CL-13

EM-74

(QR25D

E

),

EM-210

(VQ40DE

)

CL-15

(5M/T),

CL-17

(6 M/T

)

CL-20

(5M/T),

CL-22

(6M/

T)

EM-88

(QR25D

E

),

EM-225

(VQ40DE

)

SUSPECTED PARTS (Possible cause)

CLUTCH PE

DAL (F

ree

pl

ay

ou

t o

f a

d

ju

s

tm

ent

)

CLUTCH LINE (A

ir in line)

MAS

T

ER CYLINDER PIS

T

ON CUP (Damaged)

OPERA

T

ING CYLI

ND

E

R

PIST

ON CUP (Damaged)

ENGINE MOU

N

TING (Loose)

RELEA

SE BEA

RI

NG

(W

o

rn,

di

rty

or d

a

m

a

g

e

d

)

CLUTCH DIS

C

(Out

of

true)

CLUTCH DIS

C

(Runou

t i

s

ex

ce

ss

iv

e)

CLUTCH DIS

C

(Lining

broken)

CLUTCH DIS

C

(Dirty or burned)

CLUTCH DIS

C

(Oily)

CLUTCH DIS

C

(W

orn

out)

CLUTCH DIS

C

(Hardened)

CLUTCH DIS

C (Lack of

s

p

line

gre

a

s

e

)

DI

APHRAGM SPRI

N

G (Dam

ag

ed

)

DIAPHRAGM

SPRING (Out

of

tip

a

lig

nm

en

t)

PRESSURE P

L

A

T

E (Di

s

torti

on)

FL

YWHEE

L

(Distortion)

Symptom

Clutch grabs/chatters

1

2

2

2

2

2

Clutch pedal spongy

1

2

2

Clutch noisy

1

Clutch slips

1

2

2

3

4

5

Clutch does not disengage

1

2

3

4

5

5

5

5

5

5

6

6

7

CL-4

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000005589297

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-

tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000005276125

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.

Service Notice or Precautions

INFOID:0000000005276126

• Always use recommended fluid. Refer to

MA-16, "For North America: Fluids and Lubricants"

.

• Never reuse drained fluid.
• Be careful not to splash fluid on painted areas.

PIIB3706J

PRECAUTIONS

CL-5

< PRECAUTION >

C

E

F

G

H

I

J

K

L

M

A

B

CL

N

O

P

• When removing and installing clutch piping, use tool.
• Use new fluid to clean or wash all parts of master cylinder.
• Never use mineral oils such as gasoline or kerosene. It will ruin the

rubber parts of the hydraulic system.

WARNING:

After cleaning clutch disc, wipe it with a dust collector. Do not
use compressed air.

SBR686C