Nissan Frontier D40. Manual — part 43
AV-164
< PRECAUTION >
[PREMIUM AUDIO (CREW CAB)]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005568751
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
AV
PREPARATION
AV-165
< PREPARATION >
[PREMIUM AUDIO (CREW CAB)]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000005274975
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0191E
AV-166
< ON-VEHICLE REPAIR >
[PREMIUM AUDIO (CREW CAB)]
AUDIO UNIT
ON-VEHICLE REPAIR
AUDIO UNIT
Removal and Installation
INFOID:0000000005274976
REMOVAL
1.
Remove the cluster lid C. Refer to
IP-11, "Removal and Installation"
2.
Remove the center ventilator ducts. Refer to
VTL-21, "Removal and Installation"
.
3.
Remove the audio unit control screws (A), then remove the
audio unit assembly, from cluster lid C.
4.
Remove the audio unit (3) from the audio control panel (1).
5.
Remove the audio unit screws (A), using power tool, then
remove the audio unit brackets (2).
6.
Pull out the audio unit (3) from the audio control panel (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1186ZZ
ALNIA1187ZZ
AV
AUDIO AMP
AV-167
< ON-VEHICLE REPAIR >
[PREMIUM AUDIO (CREW CAB)]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
AUDIO AMP
Removal and Installation
INFOID:0000000005274977
REMOVAL
NOTE:
Do not remove the RH front seat from the vehicle.
1. Remove the RH front seat bolts, disconnect the RH front seat electrical connectors. Refer to
SE-28, "Removal and Installation"
.
2. Tilt the RH front seat back to access the audio amp (1) and
remove the audio amp. kick shield screws (C).
•
:Vehicle front
3. Disconnect the audio amp. connectors (A) and remove the
audio amp. (1) from the bracket (2).
4. Then remove the audio amp. bracket screws (B) and remove
bracket (2).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1248ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст