Nissan Frontier D40. Manual — part 300
FRONT OIL SEAL
DLN-221
< ON-VEHICLE REPAIR >
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
INSTALLATION
1.
Apply multi-purpose grease to the front oil seal lips.
2.
Install the new front oil seal using Tool.
CAUTION:
• Do not reuse oil seal.
• Do not incline oil seal when installing.
3.
Align the matching mark of drive pinion with the matching mark
A of companion flange, then install the companion flange.
4.
Apply gear oil on the screw part of drive pinion and the seating
surface of drive pinion lock nut.
5.
Install the new drive pinion lock nut and tighten to the specified
torque using suitable tool. Refer to
CAUTION:
Do not reuse drive pinion lock nut.
6.
Install the propeller shaft. Refer to
(2S1330),
DLN-153, "Removal and Installation"
(3S1310),
DLN-163, "Removal and Installation"
(3S1330) or
DLN-173, "Removal and Installation"
(3S1330-2BJ100).
Tool number
: KV38100500 (J-25273)
WDIA0234E
PDIA0675E
WDIA0241E
DLN-222
< ON-VEHICLE REPAIR >
[C200]
CARRIER COVER
CARRIER COVER
Removal and Installation
INFOID:0000000005275561
REMOVAL
1.
Drain the differential gear oil. Refer to
DLN-219, "Changing Differential Gear Oil"
2.
Disconnect the parking brake cable and brake tube from the car-
rier cover.
3.
Remove the carrier cover bolts and separate the carrier cover
from the gear carrier using Tool.
CAUTION:
• Do not damage the mating surface.
• Do not insert flat-bladed screwdriver, this will damage the
mating surface.
INSTALLATION
1.
Apply a bead of sealant to the mating surface of the carrier
cover as shown.
• Use Genuine Silicone RTV or equivalent. Refer to
"Recommended Chemical Products and Sealants"
.
CAUTION:
Remove any old sealant adhering to the mating surfaces.
Also remove any moisture, oil, or foreign material adhering
to the application and mating surfaces.
2.
Install the carrier cover to the gear carrier. Tighten the bolts to
the specified torque. Refer to
3.
Connect the parking brake cable and brake tube to the carrier
cover.
4.
Fill the rear final drive assembly with recommended differential gear oil. Refer to
.
Tool number
: KV10111100 (J-37228)
LDIA0126E
WDIA0282E
REAR FINAL DRIVE
DLN-223
< REMOVAL AND INSTALLATION >
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
REAR FINAL DRIVE
Removal and Installation
INFOID:0000000005275562
REMOVAL
CAUTION:
• Do not damage spline, companion flange and front oil seal when removing propeller shaft.
• Before removing final drive assembly or rear axle assembly, disconnect ABS sensor harness con-
nector from the assembly and move it away from final drive/rear axle assembly area. Failure to do so
may result in sensor wires being damaged and sensor becoming inoperative.
1.
Drain the differential gear oil. Refer to
DLN-219, "Changing Differential Gear Oil"
2.
Remove the rear propeller shaft. Refer to
DLN-144, "Removal and Installation"
(2S1330),
(3S1310),
DLN-163, "Removal and Installation"
(3S1330) or
3.
Remove the axle shaft. Refer to
RAX-7, "Removal and Installation"
4.
Remove the stabilizer bar. Refer to
FSU-14, "Removal and Installation"
.
5.
Disconnect the following components from the rear final drive.
• ABS sensor wire harness
• Parking brake cable
• Brake hoses and tubes
6.
Support rear final drive assembly using a suitable jack.
7.
Remove rear shock absorber lower bolts. Refer to
FSU-13, "Removal and Installation"
.
8.
Remove leaf spring U-bolt nuts. Refer to
RSU-9, "Removal and Installation"
9.
Remove rear final drive assembly
CAUTION:
Secure rear final drive assembly to the jack while removing it.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Fill the rear final drive assembly with differential gear oil after installation. Refer to
• Bleed the air from brake system. Refer to
BR-21, "Bleeding Brake System"
.
LDIA0126E
DLN-224
< DISASSEMBLY AND ASSEMBLY >
[C200]
REAR FINAL DRIVE
DISASSEMBLY AND ASSEMBLY
REAR FINAL DRIVE
Disassembly and Assembly
INFOID:0000000005275563
COMPONENTS
WDIA0281E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст