Nissan Frontier D40. Manual — part 1028
TM-10
< PREPARATION >
[FS5R30A]
PREPARATION
Commercial Service Tool
INFOID:0000000005273932
—
(J-34342)
Drift
• Installing OD main gear
• Installing reverse gear bushing
a: 44.5 mm (1.752 in) dia.
b: 40.5 mm (1.594 in) dia.
—
(J-26349-A)
Bearing Remover and Installer Set
Removing and installing mainshaft rear bear-
ing (Use with J-25726-B)
—
(J-25726-B)
Puller
Removing and installing mainshaft rear bear-
ing (Use with J-26349-A)
Tool number
(Kent-Moore No.)
Tool name
Description
NT065
WMT065
ZZA0010D
Tool name
Description
Puller
• Removing counter gear rear end bearing
• Removing reverse synchronizer hub
• Removing reverse cone
• Removing reverse gear bushing
• Removing reverse counter gear
Power tool
Loosening bolts and nuts
NT077
PBIC0190E
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
TM-11
< SYMPTOM DIAGNOSIS >
[FS5R30A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000005273933
Use the chart below to help you find the cause of the problem. The numbers indicate the order of the inspec-
tion. If necessary, repair or replace these parts.
Reference page
SUSPECTED PARTS
(Possible cause)
OI
L (L
ev
el
lo
w)
OIL (W
rong)
OI
L (L
ev
el
to
o h
ig
h
)
GASKET
(Damaged)
OIL SEAL (W
orn or
damaged)
O-RING (W
orn
or
da
ma
ge
d)
CHECK PLUG RETURN SPRING
AND
CHECK BALL
(W
orn or damaged)
SHIF
T FORK (W
o
rn)
GEAR (W
o
rn o
r da
ma
ge
d)
BEARI
N
G (W
orn or
damaged)
BAUL
K
RING (W
orn
o
r da
ma
ge
d)
INSER
T SP
RING (Dam
ag
ed
)
Symptom
Noise
1
2
3
3
Oil leakage
3
1
2
2
2
Hard to shift or will not shift
1
1
2
2
Jumps out of gear
1
2
2
TM-12
< SYMPTOM DIAGNOSIS >
[FS5R30A]
DESCRIPTION
DESCRIPTION
Description
INFOID:0000000005273934
CROSS-SECTIONAL VIEW
PCIB1296E
1.
Release bearing sleeve
2.
Front cover
3.
Main drive gear
4.
3rd and 4th shift fork
5.
Transmission case
6.
3rd and 4th coupling sleeve
7.
Striking interlock
8.
3rd main gear
9.
2nd main gear
10. 1st main gear
11.
OD main gear
12. Striking rod
13. Reverse shift fork
14. Shift lever
15. Mainshaft
16. Mainshaft rear bearing
17. Counter gear rear end bearing
18. Reverse main gear
19. Rear extension
20. OD counter gear
21. Adapter plate
22. Mainshaft front bearing
23. Drain plug
24. 1st and 2nd coupling sleeve
25. Counter gear
26. Sub-gear bracket
27. Counter gear front bearing
28. Main drive gear bearing
29. Main drive gear
M/T OIL
TM-13
< ON-VEHICLE MAINTENANCE >
[FS5R30A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ON-VEHICLE MAINTENANCE
M/T OIL
Changing
INFOID:0000000005273935
DRAINING
1.
Start the engine and let it run to warm up the transmission.
2.
Stop the engine. Remove the transmission drain plug and drain the oil.
3.
Set a gasket on the drain plug and install it to the transmission. Tighten the drain plug to the specified
torque. Refer to
.
CAUTION:
Do no reuse gasket.
FILLING
1.
Remove the filler plug. Fill with new oil until oil level reaches the
specified limit near the filler plug hole.
2.
After refilling the oil, check oil level. Set a gasket to the filler
plug, then install it to the transmission. Tighten the filler plug to the specified torque. Refer to
CAUTION:
Do not reuse gasket.
Checking
INFOID:0000000005273936
OIL LEAKAGE AND OIL LEVEL
1.
Make sure that oil is not leaking from the transmission or around it.
2.
Check oil level from the filler plug hole as shown.
CAUTION:
Do not start engine while checking oil level.
3.
Set a gasket on the filler plug and install it to the transmission.
Tighten the filler plug to the specified torque. Refer to
CAUTION:
Do not reuse gasket.
Oil grade and Viscosity:
MA-16, "For North America: Fluids and
.
Oil capacity:
MA-16, "For North America: Fluids and
.
PCIB0268E
PCIB0268E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст