Nissan Frontier D40. Manual — part 984
FRONT PASSENGER AIR BAG MODULE
SR-9
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• When servicing the SRS, do not work from directly in front of
air bag module.
• Always place front passenger air bag module with caution
label side facing upward.
• Do not insert any foreign objects (screwdriver, etc.) into air
bag module or harness connectors.
• Do not disassemble air bag module.
• Do not use old nuts after removal; replace with new nuts.
• Do not expose the front passenger air bag module to tempera-
tures exceeding 90
°
C (194
°
F).
• Replace the air bag module if it has been dropped or sus-
tained an impact.
• Do not allow oil, grease or water to come in contact with the
air bag module.
• For removal/installation of the direct-connect SRS connec-
tors, refer to
SRC-9, "Direct-connect SRS Component Con-
.
INSTALLATION
Original Passenger Air Bag Module
Installation is in the reverse order of removal.
• For removal/installation of the direct-connect SRS connectors, refer to
SRC-9, "Direct-connect SRS Compo-
CAUTION:
• Always work from the side of or under front passenger air bag module.
• After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer
Service Replacement Passenger Air Bag Module
1.
Install the front passenger air bag module to the instrument
panel pad assembly.
2.
Install the instrument panel assembly. Refer to
IP-11, "Removal and Installation"
.
3.
Connect the front passenger air bag module harness connector to yellow 4-pin service replacement air
bag connector and fasten connector to mounting bracket.
CAUTION:
• Always work from the side of or under front passenger air bag module.
• After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer
WIRING HARNESS MODIFICATION
The passenger air bag module originally installed in the vehicle uses direct-connect style harness connectors.
Service replacement passenger air bag modules use tab-locking style harness connectors. If the passenger
WHIA0111E
SBF814E
WHIA0269E
SR-10
< ON-VEHICLE REPAIR >
FRONT PASSENGER AIR BAG MODULE
air bag module is replaced or if the direct-connect harness connectors are damaged, the vehicle wiring har-
ness must be modified to allow connection of the service replacement passenger air bag module.
NOTE:
The wiring harness modification is to be performed only if the vehicle is equipped with the original passenger
air bag which uses direct-connect harness connectors. If the passenger air bag is to be replaced in a vehicle
that has already had the service replacement passenger air bag installed, the wiring harness modification is
not required.
CAUTION:
• Do not attempt to repair or replace damaged direct-connect front passenger air bag module connec-
tors. If a direct-connect harness connector is damaged, the front passenger air bag must be
replaced and the wiring harness modified.
• Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least 3
minutes.
• Always work from the side of or under front passenger air bag module.
• After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer
1.
Locate the yellow and orange direct-connect passenger air bag module harness connectors.
2.
Use wire cutters to cut back both previously used direct-connect passenger air bag module harness con-
nectors from the vehicle wiring harness approximately 50 mm (1.9 in) from the connectors.
3.
Remove approximately 150 mm (5.9 in) of the vehicle harness covering from the cut end.
4.
Slide a piece of dual-wall heat shrink tubing (provided in the pas-
senger air bag service kit) onto each wire of the previously used
vehicle wiring harness.
5.
Fold each wire back and insert into the end of the heat shrink
tubing so that the end of the wire is approximately centered in
the heat shrink tubing.
6.
Use a heat gun to shrink the heat shrink tubing and seal the wire.
7.
Use electrical tape to secure the modified circuits to the outside of the wiring harness.
8.
Locate the front passenger air bag service replacement connec-
tor that is taped back to the main harness. Unwrap the tape to
access the yellow service replacement connector and remove
the dust cover from the connector.
LHIA0017E
WHIA0062E
WHIA0118E
SIDE CURTAIN AIR BAG MODULE
SR-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE CURTAIN AIR BAG MODULE
Removal and Installation
INFOID:0000000005272899
REMOVAL
CAUTION:
• Do not attempt to repair or replace damaged direct-connect SRS component connectors. If a direct-
connect harness connector is damaged, the harness must be replaced.
• Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals and wait at
least three minutes.
• When servicing the SRS, do not work from directly in front of air bag module.
1.
Remove headlining. Refer to
INT-24, "Removal and Installation"
2.
Disconnect front and rear side curtain air bag module connectors.
• For removal/installation of the direct-connect SRS connectors, refer to
.
3.
Remove the bolts in order starting at the front or rear, and remove the side curtain air bag module.
CAUTION:
• When servicing the SRS, do not work from directly in front of air bag module.
• Do not insert any foreign objects (screwdriver, etc.) into air bag module or harness connectors.
• Do not disassemble air bag module.
• Do not expose the air bag module to temperatures exceeding 90
°
C (194
°
F).
• Replace side curtain air bag module if it has been dropped or
sustained an impact.
• Do not allow oil, grease or water to come in contact with the
air bag module.
INSTALLATION
Installation is in the reverse order of removal.
• For removal/installation of the direct-connect SRS connectors, refer to
SRC-9, "Direct-connect SRS Compo-
• After replacement of side curtain air bag module, perform self-diagnosis to check that no malfunction is
detected. Refer to
.
LHIA0100E
1.
Side curtain air bag module connector
SBF814E
SR-12
< ON-VEHICLE REPAIR >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Removal and Installation
INFOID:0000000005272900
REMOVAL
CAUTION:
• Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals and wait at
least three minutes.
1.
Disconnect the negative and positive battery terminals, then wait at least three minutes.
2.
Remove crash zone sensor nuts and shield from support mem-
ber.
3.
Disconnect the crash zone sensor harness connector.
4.
Remove crash zone sensor.
CAUTION:
• Replace crash zone sensor if it has been dropped or sustained an impact.
• Do not disassemble crash zone sensor.
INSTALLATION
Installation is in the reverse order of removal.
• After the work is complete, perform self-diagnosis to check that no malfunction is detected. Refer to
LHIA0090E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст