Nissan Frontier D40. Manual — part 1123
VTL-6
< ON-VEHICLE MAINTENANCE >
IN-CABIN MICROFILTER
ON-VEHICLE MAINTENANCE
IN-CABIN MICROFILTER
Removal and Installation
INFOID:0000000005275966
REPLACEMENT PROCEDURE
1.
Open the lower glove box and press in on the sides so that it will
open completely allowing it to hang by the cord.
2.
Depress the tab and remove the in-cabin microfilter cover as
shown.
3.
Remove the in-cabin microfilters from the heater and cooling unit housing.
4.
Insert the first new in-cabin microfilter into the heater and cool-
ing unit housing and slide it over to the right. Insert the second
new in-cabin microfilter into the heater and cooling unit housing
as shown.
NOTE:
The in-cabin microfilters are marked with air flow arrows. The
end of the microfilter with the arrow should face the rear of the
vehicle. The arrows should point downward.
5.
Install the in-cabin microfilter cover, make sure the tab is locked
in place as shown.
6.
Close the lower glove box completely.
WLIA0023E
ALIIA0359ZZ
ALIIA0360ZZ
ALIIA0359ZZ
CONTROL UNIT
VTL-7
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
ON-VEHICLE REPAIR
CONTROL UNIT
Removal and Installation
INFOID:0000000005275967
FRONT AIR CONTROL
Removal
1.
Remove cluster lid C. Refer to
2.
Remove the front air control from cluster lid C.
• For type 1, remove the four screws (A) securing the front air
control (1) to cluster lid C.
• For type 2, remove the four screws securing the front air con-
trol to cluster lid C.
Installation
Installation is in the reverse order of removal.
ALIIA0361ZZ
LBIA0416E
VTL-8
< ON-VEHICLE REPAIR >
INTAKE SENSOR
INTAKE SENSOR
Removal and Installation
INFOID:0000000005275968
REMOVAL
1.
Remove the front kick plate. Refer to
INT-18, "Removal and Installation"
2.
Remove the lower dash side finisher. Refer to
.
3.
Remove the front pillar lower finisher. Refer to
INT-18, "Removal and Installation"
4.
Remove the assist grip handle. Refer to
.
5.
Remove the front pillar upper finisher. Refer to
INT-18, "Removal and Installation"
.
6.
Remove the lower glove box. Refer to
.
7.
Remove the upper glove box (cluster lid E). Refer to
8.
Disconnect the intake sensor electrical connector.
NOTE:
The intake sensor is located on the top of the heater and cooling
unit assembly next to the A/C evaporator cover.
9.
Twist the intake sensor to remove the intake sensor from the
heater and cooling unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
WJIA1415E
BLOWER MOTOR
VTL-9
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
BLOWER MOTOR
Component
INFOID:0000000005275969
Blower Motor
Removal and Installation
INFOID:0000000005275970
REMOVAL
1.
Remove the lower glove box assembly. Refer to
.
2.
Disconnect the blower motor electrical connector.
3.
Remove the three screws and remove the blower motor.
INSTALLATION
Installation is in the reverse order of removal.
WJIA1479E
1.
Heater and cooling unit assembly
2.
Blower motor
3.
Variable blower control/Blower
motor resistor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст