Nissan Frontier D40. Manual — part 873
PB-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005589336
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
PREPARATION
PB-3
< PREPARATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000005276038
(Kent-Moore No.)
Tool name
Description
(J-21177-A)
Brake drum clearance gauge
Measuring rear rotor drum to parking
brake shoe clearance
Power tool
Loosening bolts and nuts
WFIA0167E
PIIB1407E
PB-4
< ON-VEHICLE REPAIR >
PARKING BRAKE SYSTEM
ON-VEHICLE REPAIR
PARKING BRAKE SYSTEM
On-Vehicle Service
INFOID:0000000005598070
LEVER STROKE
• When parking brake lever is operated with the specified force, make sure the stroke is within the specified
number of notches. Check by listening and counting the ratchet clicks.
INSPECTION
• Make sure the components are attached properly, checking for looseness or backlash.
• Check parking brake lever assembly for bends, damage and cracks, and replace if necessary.
• Check cable for wear and damage, and replace if necessary.
• Check parking brake warning lamp switch for malfunction, and replace if necessary. Refer to
.
ADJUSTMENT
1.
Remove rear half of the center console. Refer to
IP-19, "Disassembly and Assembly"
2.
Rotate adjusting nut and loosen cable until tension is sufficiently
released.
3.
Remove the rear wheels and tires. Refer to
.
4.
Using wheel nuts, secure the disc to the hub to prevent it from tilting.
5.
Remove the adjuster hole plug installed on the disc rotor. Turn
the adjuster in direction (A) using a suitable tool as shown, until
disc rotor is locked. Turn the adjuster in the opposite direction by
5 or 6 notches after locking.
6.
Rotate disc rotor to make sure there is no drag.
7.
Adjust cable as follows:
a.
Rotate the adjusting nut to adjust the parking brake lever operat-
ing force to 294N (29.9Kg, 66.0 lb-ft) just before a full lever stroke 229.0mm (9.0in).
CAUTION:
Do not reuse the adjusting nut after removing it.
b.
When replacing brake cable, operate parking brake lever 10 or more times with a full stroke of 229.0mm
(9.0 in).
c.
Release the parking brake lever and rotate the disc rotor to make sure there is no drag.
d.
Rotate adjusting nut to adjust lever stroke to specification.
e.
With parking brake lever completely disengaged, make sure there is no drag on the parking brake.
Lever stroke
: 6
−
8 notches [under force of 196 N (20.0 kg-f, 44.1 lb-f)]
LFIA0247E
B: Left
C: Right
: Front
Lever stroke
: 6
−
8 notches [under force of
196 N (20.0 kg-f, 44.1 lb-f)]
ALFIA0173GB
PARKING BRAKE CONTROL
PB-5
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Component
INFOID:0000000005598071
1.
Control lever assembly
2.
Front cable grommet
3.
Left rear cable
4.
Pin
5.
Right rear cable
6.
Return spring
7.
Equalizer
8.
Front cable
9.
Adjusting nut
A.
Refer to installation for tighting
AWFIA0487GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст