Nissan Frontier D40. Manual — part 712
GW-16
< ON-VEHICLE REPAIR >
FRONT DOOR GLASS AND REGULATOR
FRONT DOOR GLASS AND REGULATOR
Front Door Glass
INFOID:0000000005274593
REMOVAL
1.
Remove the front door finisher. Refer to
INT-14, "Removal and Installation"
2.
Position the vapor barrier aside.
3.
Remove the window inside seal.
4.
If equipped, temporarily reconnect the power window switch.
5.
For power windows, operate the power window switch to raise/
lower the door window until the glass bolts can be seen.
6.
For manual windows, temporarily reinstall the window crank
handle and lower the window until the glass bolts can be seen.
7.
Remove the glass bolts.
8.
While holding the door window, raise it at the rear and pull the
glass out of the sash toward the outside of the door.
INSTALLATION
Installation is in the reverse order of removal.
• Check the glass for proper fit. Follow the FITTING INSPECTION procedure.
• On the drivers door, reset the motor if equipped. Follow the SETTING AFTER INSTALLATION procedure.
FITTING INSPECTION
• Check that the glass fits securely into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass and guide rail bolts to adjust the glass position.
Front Door Glass Regulator
INFOID:0000000005274594
REMOVAL
1.
Remove the front door finisher. Refer to
INT-14, "Removal and Installation"
LIIA1686E
LIIA1687E
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
Regulator and motor
or manual crank as-
sembly bolts
: 5.7 N·m (0.58 kg-m, 50 in-lb)
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
FRONT DOOR GLASS AND REGULATOR
GW-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
2.
Position the vapor barrier aside.
3.
If equipped, temporarily reconnect the power window switch.
4.
For power windows, operate the power window switch to raise/
lower the door window until the glass bolts can be seen.
5.
For manual windows, temporarily reinstall the window crank
handle and lower the window until the glass bolts can be seen.
6.
Remove the glass bolts.
7.
Raise the front door glass and hold it in place with suitable tool
(A).
8.
If equipped, disconnect the harness connector from the regula-
tor assembly.
9.
Remove the bolts and the regulator assembly.
DISASSEMBLY AND ASSEMBLY
Remove the regulator motor or manual crank assembly from the regulator assembly.
INSPECTION AFTER REMOVAL
LIIA1686E
PIIB3510J
Front
WIIA1033E
GW-18
< ON-VEHICLE REPAIR >
FRONT DOOR GLASS AND REGULATOR
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Wire wear
• Regulator deformation
• Grease condition for each sliding part
INSTALLATION
1.
Install the regulator assembly.
a.
Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor or
crank assembly to install the assembly in the door.
b.
Install the top front regulator bolt.
c.
Install the bottom front regulator bolt.
d.
Install the bottom rear regulator bolt.
e.
Tighten the top rear regulator bolt.
f.
Install the top window motor or manual crank assembly bolt.
g.
Install the lower window motor or manual crank assembly bolt
h.
Install the rear window motor or manual crank assembly bolt.
2.
If equipped, connect the harness connector to the regulator assembly.
Front
Regulator and motor or
manual crank assembly
bolts
: 5.7 N·m (0.58 kg-m, 50 in-lb)
WIIA1033E
FRONT DOOR GLASS AND REGULATOR
GW-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
3.
Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten glass bolts.
4.
Check the glass for proper fit. Follow the FITTING INSPECTION procedure .
5.
On the drivers door, reset the motor (if equipped). Follow the SETTING AFTER INSTALLATION proce-
dure .
6.
Install the inside seal.
7.
Reposition the vapor barrier.
8.
Install front door finisher. Refer to
INT-14, "Removal and Installation"
.
SETTING AFTER INSTALLATION
Setting of Limit Switch
If any of the following work has been done, set the limit switch (integrated in the motor).
• Removal and installation of the regulator.
• Removal and installation of the motor from the regulator.
• Removal and installation of the glass.
• Removal and installation of the glass run.
Resetting
After installing each component, perform the following procedure to reset the limit switch.
1.
Raise the glass to the top position.
2.
While pressing and holding the reset switch, lower the glass to
the bottom position.
3.
Release the reset switch. Verify that the reset switch returns to
the original position, if not, pull the switch using suitable tool.
4.
Raise the glass to the top position.
CAUTION:
Do not operate the glass automatically to raise the glass to
the top position.
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
LIIA1686E
SIIA0347E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст