Nissan Frontier D40. Manual — part 382
P0442 EVAP CONTROL SYSTEM
EC-219
< COMPONENT DIAGNOSIS >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
OK
>> GO TO 15.
NG
>> Repair or reconnect the hose.
15.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-228, "Component Inspection"
OK or NG
OK
>> GO TO 16.
NG
>> Replace EVAP canister purge volume control solenoid valve.
16.
CHECK FUEL TANK TEMPERATURE SENSOR
EC-180, "Component Inspection"
OK or NG
OK
>> GO TO 17.
NG
>> Replace fuel level sensor unit.
17.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-243, "Component Inspection"
OK or NG
OK
>> GO TO 18.
NG
>> Replace EVAP control system pressure sensor.
18.
CHECK EVAP PURGE LINE
Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks or improper connection.
Refer to
OK or NG
OK
>> GO TO 19.
NG
>> Repair or reconnect the hose.
19.
CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
>> GO TO 20.
20.
CHECK EVAP/ORVR LINE
Check EVAP/ORVR line between EVAP canister and fuel tank for clogging, kinks, looseness and improper
connection. For location, refer to
OK or NG
OK
>> GO TO 21.
NG
>> Repair or replace hoses and tubes.
21.
CHECK RECIRCULATION LINE
Check recirculation line between fuel filler tube and fuel tank for clogging, kinks, cracks, looseness and
improper connection.
OK or NG
OK
>> GO TO 22.
NG
>> Repair or replace hoses, tubes or fuel filler tube.
22.
CHECK REFUELING EVAP VAPOR CUT VALVE
EC-389, "Component Inspection"
OK or NG
OK
>> GO TO 23.
NG
>> Replace refueling EVAP vapor cut valve with fuel tank.
23.
CHECK FUEL LEVEL SENSOR
MWI-33, "Component Inspection"
.
OK or NG
OK
>> GO TO 24.
EC-220
< COMPONENT DIAGNOSIS >
[QR25DE]
P0442 EVAP CONTROL SYSTEM
NG
>> Replace fuel level sensor unit.
24.
CHECK INTERMITTENT INCIDENT
GI-46, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000005273212
FUEL TANK VACUUM RELIEF VALVE (BUILT INTO FUEL FILLER CAP)
1.
Turn ignition switch OFF.
2.
Remove fuel filler cap.
3.
Wipe clean valve housing.
4.
Install fuel filler cap adapter (commercial service tool) to fuel filler cap.
5.
Check valve opening pressure and vacuum.
6.
If out of specification, replace fuel filler cap as an assembly.
CAUTION:
Use only a genuine fuel filler cap as a replacement. If an incor-
rect fuel filler cap is used, the MIL may illuminate.
SEF445Y
Pressure:
15.3 - 20.0 kPa
(0.156 - 0.204 kg/cm
2
, 2.22 - 2.90 psi)
Vacuum:
−
6.0 to
−
3.3 kPa
(
−
0.061 to
−
0.034 kg/cm
2
,
−
0.87 to
−
0.48 psi)
SEF943S
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-221
< COMPONENT DIAGNOSIS >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Description
INFOID:0000000005273213
SYSTEM DESCRIPTION
*1: ECM determines the start signal status by the signals of engine speed and battery voltage.
*2: This signal is sent to the ECM though CAN communication line.
This system controls flow rate of fuel vapor from the EVAP canister. The opening of the vapor by-pass pas-
sage in the EVAP canister purge volume control solenoid valve changes to control the flow rate. The EVAP
canister purge volume control solenoid valve repeats ON/OFF operation according to the signal sent from the
ECM. The opening of the valve varies for optimum engine control. The optimum value stored in the ECM is
determined by considering various engine conditions. When the engine is operating, the flow rate of fuel vapor
from the EVAP canister is regulated as the air flow changes.
COMPONENT DESCRIPTION
The EVAP canister purge volume control solenoid valve is used to
control the flow rate of fuel vapor from the EVAP canister. The EVAP
canister purge volume control solenoid valve is moved by ON/OFF
pulses from the ECM. The longer the ON pulse, the greater the
amount of fuel vapor that will flow through the valve.
On Board Diagnosis Logic
INFOID:0000000005273214
DTC Confirmation Procedure
INFOID:0000000005273215
NOTE:
Sensor
Input Signal to ECM
ECM function
Actuator
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Engine speed*
1
EVAP canister purge
flow control
EVAP canister purge volume
control solenoid valve
Mass air flow sensor
Amount of intake air
Engine coolant temperature sensor
Engine coolant temperature
Battery
Battery voltage*
1
Throttle position sensor
Throttle position
Accelerator pedal position sensor
Accelerator pedal position
Air fuel ratio (A/F) sensor 1
Density of oxygen in exhaust gas
(Mixture ratio feedback signal)
Fuel tank temperature sensor
Fuel temperature in fuel tank
Wheel sensor
Vehicle speed*
2
PBIB2057E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0443
0443
EVAP canister purge
volume control solenoid
valve
The canister purge flow is detected during the
specified driving conditions, even when EVAP
canister purge volume control solenoid valve is
completely closed.
• EVAP control system pressure sensor
• EVAP canister purge volume control so-
lenoid valve
(The valve is stuck open.)
• EVAP canister vent control valve
• EVAP canister
• Hoses
(Hoses are connected incorrectly or
clogged.)
EC-222
< COMPONENT DIAGNOSIS >
[QR25DE]
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Always perform test at a temperature of 5
°
C (41
°
F) or more.
WITH CONSULT-III
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON.
4.
Select “PURG VOL CN/V P1444” of “EVAPORATIVE SYSTEM” in “DTC WORK SUPPORT” mode with
CONSULT-III.
5.
Touch “START”.
6.
Start engine and let it idle until “TESTING” on CONSULT-III changes to “COMPLETED”. (It will take
approximately 10 seconds.)
If “TESTING” is not displayed after 5 minutes, retry from step 2.
7.
Make sure that “OK” is displayed after touching “SELF-DIAG RESULTS”. If “NG” is displayed, refer to
WITH GST
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Start engine and let it idle for at least 20 seconds.
4.
Select Service $07 with GST.
5.
If 1st trip DTC is detected, go to
Diagnosis Procedure
INFOID:0000000005273216
1.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect EVAP canister purge volume control solenoid valve
harness connector.
3.
Turn ignition switch ON.
4.
Check voltage between EVAP canister purge volume control
solenoid valve terminal 1 and ground with CONSULT-III or
tester.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
BBIA0620E
Voltage: Battery voltage
PBIB2651E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст