Nissan Frontier D40. Manual — part 1154
HAZARD WARNING LAMPS FLASH
WT-39
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
HAZARD WARNING LAMPS FLASH
Hazard Warning Lamps Flash When Ignition Switch Is Turned On
INFOID:0000000005275753
DIAGNOSTIC PROCEDURE
1.
CHECK BCM GROUND CIRCUIT
Check BCM ground circuit. Refer to
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-54, "Removal and Installation"
NO
>> Repair BCM ground circuit.
WT-40
< SYMPTOM DIAGNOSIS >
ID REGISTRATION CANNOT BE COMPLETED
ID REGISTRATION CANNOT BE COMPLETED
ID Registration Cannot Be Completed
INFOID:0000000005275754
DIAGNOSTIC PROCEDURE
1.
PERFORM ID REGISTRATION OF ALL TRANSMITTERS
Carry out ID registration of all transmitters. Refer to
WT-6, "ID Registration Procedure"
Can ID registration of all transmitters be completed?
YES
>> Inspection End.
NO
>> GO TO
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
WT-41
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000005275755
Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
—
—
(R18
0A),
(C20
0),
(M
22
6)
,
,
Re
fe
r
to
TIRES in thi
s
ch
art.
Refe
r to
ROAD WHEE
L i
n
t
h
is cha
rt.
Possible cause and SUSPECTED PARTS
Out-of
-round
Im
ba
la
n
c
e
In
correct tire
pressure
Un
ev
en
ti
re we
ar
Def
o
rmat
io
n
or da
ma
ge
No
n-u
n
if
orm
ity
In
correct tire
size
FRO
N
T A
ND RE
A
R
FI
NA
L
D
R
IV
E
F
R
ONT
AXLE AND FRONT S
U
SPENSION
REA
R
AXLE AND REAR S
U
SPENSION
TI
RE
S
ROAD W
H
EEL
BR
AK
E
S
T
EERING
Symptom
TIRES
Noise
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
×
×
Shudder
×
×
×
×
×
×
×
×
×
×
×
Poor quality ride
or handling
×
×
×
×
×
×
×
×
×
ROAD
WHEEL
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Shimmy, shudder
×
×
×
×
×
×
×
×
Poor quality ride
or handling
×
×
×
×
×
×
WT-42
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005531984
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for work
INFOID:0000000005275757
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст