Nissan Frontier D40. Manual — part 53
BCS-22
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
IMMU
IMMU : CONSULT-III Function (BCM - IMMU)
INFOID:0000000005275682
DATA MONITOR
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)
INFOID:0000000005275683
WORK SUPPORT
*: Initial setting
DATA MONITOR
PASSING SW
[OFF/ON]
Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
reading function
AUTO LIGHT SW
[OFF/ON]
Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function
FR FOG SW
[OFF/ON]
Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function
FR WIPER HI
[OFF/ON]
Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function
FR WIPER LOW
[OFF/ON]
Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function
FR WIPER INT
[OFF/ON]
Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function
FR WASHER SW
[OFF/ON]
Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function
INT VOLUME
[1 - 7]
Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading
function
Monitor Item
[Unit]
Description
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Indicates condition of ignition switch in ON position.
Test Item
Description
THEFT IND
This test is able to check security indicator operation [ON/OFF].
Work Item
Setting Item
Setting
ROOM LAMP TIMER SET
MODE 1*
30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
60 min.
MODE 3
10 min.
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judges from IGN signal (ignition power supply)
KEY ON SW [ON/OFF]
The switch status input from key switch
DOOR SW-DR [ON/OFF]
The switch status input from front door switch (driver side)
DOOR SW-AS [ON/OFF]
The switch status input from front door switch (passenger side)
DOOR SW-RR [ON/OFF]
The switch status input from rear door switch RH
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-23
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
*: Each lamp switch is in ON position.
RETAINED PWR
RETAINED PWR : CONSULT-III Function (BCM - RETAINED PWR)
INFOID:0000000005275685
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER)
INFOID:0000000005275686
DATA MONITOR
DOOR SW- RL [ON/OFF]
The switch status input from rear door switch LH
KEY CYL LK-SW [ON/OFF]
Lock switch status input from door key cylinder switch
KEY CYL UN-SW [ON/OFF]
Unlock switch status input from door key cylinder switch
CDL LOCK SW [ON/OFF]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW [ON/OFF]
Unlock switch status input from door lock and unlock switch
KEYLESS LOCK [ON/OFF]
Lock signal status received from remote keyless entry receiver (integrated in the
BCM)
KEYLESS UNLOCK [ON/OFF]
Unlock signal status received from remote keyless entry receiver (integrated in the
BCM)
Monitor Item
[Unit]
Description
Test Item
Operation
Description
BATTERY SAVER
OFF
Cuts the interior room lamp power supply to turn interior room lamps OFF.
ON
Outputs the interior room lamp power supply to turn interior room lamps ON.*
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Indicates condition of ignition switch.
DOOR SW-DR [ON/OFF]
Indicates condition of front door switch LH.
DOOR SW-AS [ON/OFF]
Indicates condition of front door switch RH.
Test Item
Description
RETAINED PWR
This test is able to supply RAP signal (power) from BCM (body control module) to power window
system and power sunroof system (if equipped). Those systems can be operated when turning on
“RETAINED PWR” on CONSULT-III screen even if the ignition switch is turned OFF.
NOTE:
During this test, CONSULT-III can be operated with ignition switch in OFF position. “RETAINED
PWR” should be turned “ON” or “OFF” on CONSULT-III screen when ignition switch is ON. Then
turn ignition switch OFF to check retained power operation. CONSULT-III might be stuck if “RE-
TAINED PWR” is turned “ON” or “OFF” on CONSULT-III screen when ignition switch is OFF.
Work item
Description
RETAINED PWR SET
RAP signal’s power supply period can be changed by mode setting. Selects RAP signal’s power
supply period between three steps
• MODE1 (45 sec.)/MODE2 (OFF)/MODE 3 (2 min.).
BCS-24
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : Diagnosis Description
INFOID:0000000005275687
DESCRIPTION
During driving, the TPMS receives the signal transmitted from the transmitter installed in each wheel, when
the tire pressure becomes low. The control unit (BCM) of this system has pressure judgment and trouble diag-
nosis functions.
When the TPMS detects low inflation pressure or another unusual symptom, the warning lamps in the combi-
nation meter comes on.
SELF DIAGNOSTIC PROCEDURE (WITH CONSULT-III)
With CONSULT-III
• Touch “SELF-DIAG RESULTS” display to show malfunction experienced since the last erasing operation.
SELF DIAGNOSTIC PROCEDURE (WITHOUT CONSULT-III)
Without CONSULT-III
To start the self-diagnostic results mode, ground terminal of the tire pressure warning check connector. The
malfunction location is indicated by the warning lamp flashing.
NOTE:
When the low tire warning lamp flashes 5 Hz and continues repeating it, the system is normal.
Monitor Item
[Unit]
Description
OIL PRESS SW [ON/OFF]
Displays the status of oil pressure switch received from IPDM E/R via CAN communication.
Test Item
Operation
Description
OIL PRESSURE SW
OFF
OFF
ON
BCM transmits the oil pressure switch signal to the combination meter via CAN communica-
tion, which operates the oil pressure gauge in the combination meter.
SEIA0745E
Flickering
pattern
Items
Diagnostic items detected when···
Check item
15
Tire pressure value (Front LH)
Front LH tire pressure drops to 181 kPa (1.8 kg/cm, 25.25 psi) or less.
–
16
Tire pressure value (Front RH)
Front RH tire pressure drops to 181 kPa (1.8 kg/cm, 25.25 psi) or less.
17
Tire pressure value (Rear RH)
Rear RH tire pressure drops to 181 kPa (1.8 kg/cm, 25.25 psi) or less.
18
Tire pressure value (Rear LH)
Rear LH tire pressure drops to 181 kPa (1.8 kg/cm, 25.25 psi) or less.
21
Transmitter no data (Front LH)
Data from front LH transmitter can not be received.
22
Transmitter no data (Front RH)
Data from front RH transmitter can not be received.
23
Transmitter no data (Rear RH)
Data from Rear RH transmitter can not be received.
24
Transmitter no data (Rear LH)
Data from Rear LH transmitter can not be received.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-25
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ERASE SELF-DIAGNOSIS
With CONSULT-III
1.
Perform applicable inspection of malfunctioning item and then repair or replace.
2.
Turn ignition switch “ON” and select “SELF-DIAG RESULTS” mode for “AIR PRESSURE MONITOR” with
CONSULT-III.
3.
Touch “ERASE” on CONSULT-III screen to erase memory.
Without CONSULT-III
• In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is
stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned “ON” and “OFF”.
• However, this information is erased by turning ignition switch “OFF” after performing self-diagnostic or by
erasing the memory using the CONSULT-III.
AIR PRESSURE MONITOR : CONSULT-III Function
INFOID:0000000005275688
WORK SUPPORT
31
Transmitter checksum error
(Front LH)
Checksum data from front LH transmitter is malfunctioning.
32
Transmitter checksum error
(Front RH)
Checksum data from front RH transmitter is malfunctioning.
33
Transmitter checksum error
(Rear RH)
Checksum data from rear RH transmitter is malfunctioning.
34
Transmitter checksum error
(Rear LH)
Checksum data from rear RH transmitter is malfunctioning.
35
Transmitter pressure data error
(Front LH)
Air pressure data from front LH transmitter is malfunction.
36
Transmitter pressure data error
(Front RH)
Air pressure data from front RH transmitter is malfunction.
37
Transmitter pressure data error
(Rear RH)
Air pressure data from rear RH transmitter is malfunction.
38
Transmitter pressure data error
(Rear LH)
Air pressure data from rear LH transmitter is malfunction.
41
Transmitter function code error
(Front LH)
Function code data from front LH transmitter is malfunction.
42
Transmitter function code error
(Front RH)
Function code data from front RH transmitter is malfunction.
43
Transmitter function code error
(Rear RH)
Function code data from rear RH transmitter is malfunction.
44
Transmitter function code error
(Rear LH)
Function code data from rear LH transmitter is malfunction.
45
Transmitter battery voltage low
(Front LH)
Battery voltage of front LH transmitter drops.
46
Transmitter battery voltage low
(Front RH)
Battery voltage of front RH transmitter drops.
47
Transmitter battery voltage low
(Rear RH)
Battery voltage of rear RH transmitter drops.
48
Transmitter battery voltage low
(Rear LH)
Battery voltage of rear LH transmitter drops.
52
Vehicle speed signal error
Speed signal is not detected.
No flicker-
ing
Tire pressure warning check
switch
Tire pressure warning switch circuit is open.
–
Flickering
pattern
Items
Diagnostic items detected when···
Check item
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст