Nissan Frontier D40. Manual — part 280
PREPARATION
DLN-141
< PREPARATION >
[PROPELLER SHAFT: 2S1330]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000005275504
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
DLN-142
< FUNCTION DIAGNOSIS >
[PROPELLER SHAFT: 2S1330]
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
FUNCTION DIAGNOSIS
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000005275505
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
Possible cause and suspected parts
Une
v
en
rot
a
ti
on
torq
ue
Rot
a
ti
on
im
ba
la
nc
e
Ex
ce
ss
iv
e run
ou
t
Di
ff
ere
n
ti
al
Axle
Su
sp
en
si
on
Ti
re
s
Road wheel
Driv
e sh
af
t
Brak
es
S
tee
ring
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
PROPELLER SHAFT
DLN-143
< ON-VEHICLE REPAIR >
[PROPELLER SHAFT: 2S1330]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ON-VEHICLE REPAIR
PROPELLER SHAFT
On-Vehicle Service
INFOID:0000000005275506
APPEARANCE AND NOISE INSPECTION
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace the propeller shaft assembly.
• Check the bearings for noise and damage. Repair or replace the bearings as necessary.
PROPELLER SHAFT VIBRATION
If a vibration is present at high speed, inspect the propeller shaft runout first.
1.
Measure the runout of the propeller shaft tube at several points
by rotating the final drive companion flange with your hands.
Refer to
DLN-148, "General Specification"
.
2.
If the runout exceeds specifications, disconnect the propeller
shaft at the final drive companion flange; then rotate the com-
panion flange 90
°
, 180
°
and 270
°
and reconnect the propeller
shaft.
3.
Check the runout again. If the runout still exceeds specifications,
replace the propeller shaft assembly.
4.
After installation, check for vibration by driving vehicle.
LDIA0161E
LDIA0121E
DLN-144
< REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2S1330]
PROPELLER SHAFT
REMOVAL AND INSTALLATION
PROPELLER SHAFT
Removal and Installation
INFOID:0000000005275507
COMPONENTS
REMOVAL
1.
Move the M/T or A/T shift selector lever to the N position and release the parking brake.
2.
Put matching marks on the rear propeller shaft flange yoke and
the rear final drive companion flange as shown.
CAUTION:
For matching marks, use paint. Never damage the rear pro-
peller shaft flange yoke or the companion flange.
3.
Remove the bolts, then remove the propeller shaft from the rear
final drive and transfer.
INSPECTION
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke
5.
Journal
6.
Flange yoke
Front
AWBIA0800GB
WDIA0049E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст