Nissan Murano Z50 (2006 year). Manual — part 126
CAMSHAFT
EM-85
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2006 August
2006 Murano
●
Install camshaft so that dowel pin hole and dowel pin on front
end face are positioned as shown in figure. (No. 1 cylinder
TDC on its compression stroke)
NOTE:
●
Large and small pin holes are located on front end face of
camshaft (INT), at intervals of 180 degrees. Face small dia.
side pin hole upward (in cylinder head upper face direc-
tion).
●
Though camshaft does not stop at the portion as shown in
the figure, for the placement of cam nose, it is generally
accepted camshaft is placed for the same direction of the
figure.
4.
Install camshaft brackets.
●
Remove foreign material completely from camshaft bracket
backside and from cylinder head installation face.
●
Install camshaft bracket in original position and direction as
shown in figure.
●
Install camshaft brackets (No. 2 to 4) aligning the stamp
marks as shown in the figure.
NOTE:
There are no identification marks indicating left and right for
camshaft bracket (No. 1).
PBIC2478E
SEM446G
PBIC2052E
EM-86
CAMSHAFT
Revision: 2006 August
2006 Murano
●
Apply liquid gasket to mating surface of camshaft bracket (No.
1) as shown on right and left banks.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS"
.
5.
Tighten camshaft bracket bolts in the following steps, in numeri-
cal order as shown.
a.
Tighten No. 7 to 10 in order as shown.
b.
Tighten No. 1 to 6 in order as shown.
c.
Tighten No. 1 to 10 in numerical order as shown.
d.
Tighten No. 1 to 6 in numerical order as shown.
e.
Tighten No. 7 to 10 in numerical order as shown.
CAUTION:
After tightening mounting bolts of camshaft brackets (No.
1), be sure to wipe off excessive liquid gasket from the
parts list below.
●
Mating surface of rocker cover
●
Mating surface of rear timing chain case
PBIC2660E
: 1.96 N·m (0.20 kg-m, 1 ft-lb)
: 1.96 N·m (0.20 kg-m, 1 ft-lb)
: 5.88 N·m (0.60 kg-m, 4 ft-lb)
: 10.4 N·m (1.1 kg-m, 8 ft-lb)
: 9.3 N·m (0.95 kg-m, 7 ft-lb)
PBIC2050E
CAMSHAFT
EM-87
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2006 August
2006 Murano
6.
Measure difference in levels between front end faces of cam-
shaft bracket (No. 1) and cylinder head.
●
Measure two positions (both intake and exhaust side) for a
single bank.
●
If the measured value is out of the standard, re-install cam-
shaft bracket (No. 1).
7.
Inspect and adjust the valve clearance. Refer to
8.
Install in the reverse order of removal after this step.
INSPECTION AFTER INSTALLATION
Inspection of Camshaft Sprocket (INT) Oil Groove
CAUTION:
●
Perform this inspection only when DTC P0011 or P0021 are detected in self-diagnostic results of
CONSULT-II and it is directed according to inspection procedure of EC section. Refer to
.
●
Check when engine ins cold so as to prevent burns from any splashing engine oil.
1.
Check the engine oil level. Refer to
2.
Perform the following procedure so as to prevent the engine from being unintentionally started while
checking.
a.
Release fuel pressure. Refer to
EC-78, "FUEL PRESSURE RELEASE"
b.
Disconnect ignition coil and injector harness connectors.
3.
Remove intake valve timing control solenoid valve. Refer to
4.
Crank the engine, and then make sure that engine oil comes out
from camshaft bracket (No. 1) oil hole. End crank after checking.
WARNING:
Be careful not to touch rotating parts (drive belts, idler pul-
ley, and crankshaft pulley, etc.).
CAUTION:
Engine oil may squirt from intake valve timing control sole-
noid valve installation hole during cranking. Use a shop
cloth to prevent the engine components and the vehicle. Do
not allow engine oil to get on rubber components such as
drive belt or engine mount insulators. Immediately wipe off
any splashed engine oil.
●
Clean oil groove between oil strainer and intake valve timing control solenoid valve if engine oil does not
come out from camshaft bracket (No. 1) oil hole. Refer to
5.
Remove components between intake valve timing control solenoid valve and camshaft sprocket (INT),
and then check each oil groove for clogging.
●
Clean oil groove if necessary. Refer to
6.
After inspection, install removed parts.
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.
●
Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-10, "RECOMMENDED FLUIDS AND LUBRICANTS"
●
Use procedure below to check for fuel leakage.
–
Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
–
Start engine. With engine speed increased, check again for fuel leakage at connection points.
●
Run engine to check for unusual noise and vibration.
Standard
: –0.14 to 0.14 mm (–0.0055 to 0.0055 in)
EMQ0044D
PBIC2869E
EM-88
CAMSHAFT
Revision: 2006 August
2006 Murano
NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal/installation, slack guide may gener-
ate a pounding noise during and just after engine start. However, this is normal. Noise will stop after
hydraulic pressure rises.
●
Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.
●
Bleed air from lines and hoses of applicable lines, such as in cooling system.
●
After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.
Valve Clearance
NBS0029O
INSPECTION
In cases of removing/installing or replacing camshaft and valve-
related parts, or of unusual engine conditions due to changes in
valve clearance (found malfunctions during stating, idling or causing
noise), perform inspection as follows:
1.
Remove rocker covers (right and left banks). Refer to
.
2.
Measure the valve clearance as follows:
a.
Set No. 1 cylinder at TDC of its compression stroke.
●
Rotate crankshaft pulley clockwise to align timing mark
(grooved line without color) with timing indicator.
Items
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Other oils and fluid*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gases
—
Leakage
—
SEM713A
SEM918G
CAMSHAFT
EM-89
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2006 August
2006 Murano
●
Make sure that intake and exhaust cam noses on No. 1 cylin-
der (engine front side of right bank) are located as shown in
the figure.
●
If not, turn crankshaft one revolution (360 degrees) and align
as shown in the figure.
b.
Use a feeler gauge, measure the clearance between valve lifter
and camshaft.
Valve clearance:
Unit: mm (in)
*: Approximately 80
°
C (176
°
F)
●
By referring to the figure, measure the valve clearances at
locations marked “
×
” as shown in the table below (locations
indicated in the figure).
●
No. 1 cylinder at compression TDC
c.
Rotate crankshaft by 240 degrees clockwise (when viewed from engine front) to align No.3 cylinder at
TDC of its compression stroke.
SEM418G
SEM139D
Items
Cold
Hot * (reference data)
Intake
0.26 - 0.34 (0.010 - 0.013)
0.304 - 0.416 (0.012 - 0.016)
Exhaust
0.29 - 0.37 (0.011 - 0.015)
0.308 - 0.432 (0.012 - 0.017)
Measuring position (right bank)
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 1 cylinder at
compression TDC
EXH
×
INT
×
Measuring position (left bank)
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 1 cylinder at
compression TDC
INT
×
EXH
×
PBIC2054E
EM-90
CAMSHAFT
Revision: 2006 August
2006 Murano
NOTE:
To align cylinder No.3 with the compression top dead center,
place matching marks (A) on the crankshaft pulley (1) side and
on the cylinder block side at a point 240
°
counterclockwise from
the compression top dead center using the hex head of the
crankshaft pulley bolt as a guide.
●
By referring to the figure, measure the valve clearances at
locations marked “
×
” as shown in the table below (locations
indicated in the figure).
●
No. 3 cylinder at compression TDC
d.
Rotate crankshaft by 240 degrees clockwise (when viewed from engine front) to align No.5 cylinder at
TDC of compression stroke.
NOTE:
To align cylinder No.5 with the compression top dead center,
place matching marks (A) on the crankshaft pulley (1) side and
on the cylinder block side at a point 240
°
counterclockwise from
the compression top dead center using the hex head of the
crankshaft pulley bolt as a guide.
PBIC4628J
Measuring position (right bank)
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 3 cylinder at
compression TDC
EXH
×
INT
×
Measuring position (left bank)
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 3 cylinder at
compression TDC
INT
×
EXH
×
PBIC2055E
PBIC4628J
CAMSHAFT
EM-91
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2006 August
2006 Murano
●
By referring to the figure, measure the valve clearances at
locations marked “
×
” as shown in the table below (locations
indicated in the figure).
●
No. 5 cylinder at compression TDC
3.
For the measured value are out of the standard, perform adjustment. Refer to
ADJUSTMENT
●
Perform adjustment depending on selected head thickness of valve lifter.
1.
Measure the valve clearance. Refer to
2.
Remove camshaft. Refer to
3.
Remove valve lifters at the locations that are out of the standard.
4.
Measure the center thickness of the removed valve lifters with a
micrometer.
5.
Use the equation below to calculate valve lifter thickness for replacement.
Measuring position (right bank)
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 5 cylinder at
compression TDC
EXH
×
INT
×
Measuring position (left bank)
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 5 cylinder at
compression TDC
INT
×
EXH
×
PBIC2056E
KBIA0057E
Valve lifter thickness calculation:
t = t
1
+ (C
1
– C
2
)
t
= Valve lifter thickness to be replaced
t
1
= Removed valve lifter thickness
C
1
= Measured valve clearance
C
2
= Standard valve clearance:
Intake
: 0.30 mm (0.012 in)*
Exhaust
: 0.33 mm (0.013 in)*
*: Approximately 20
°
C (68
°
F)
EM-92
CAMSHAFT
Revision: 2006 August
2006 Murano
●
Thickness of new valve lifter can be identified by stamp marks
on the reverse side (inside the cylinder).
Stamp mark 788U, 788R or 788V indicates 7.88 mm (0.3102
in) in thickness.
NOTE:
Three types of stamp marks are used for parallel setting and
for manufacturer identification.
Available thickness of valve lifter: 27 sizes with range 7.88 to 8.40 mm (0.3102 to 0.3307 in) in steps of
0.02 mm (0.0008 in) (when manufactured at factory). Refer to
EM-145, "Available Valve Lifter"
CAUTION:
●
Install identification letters at each of proper positions.
●
Never mis-install the valve lifter.
6.
Install selected valve lifter.
7.
Install camshaft. Refer to
8.
Manually turn crankshaft pulley a few turns.
9.
Make sure that the valve clearances for cold engine are within the specifications by referring to the speci-
fied values. Refer to
.
10. Install all removal parts in the reverse order of removal. Refer to
.
11. Warm up the engine, and check for unusual noise and vibration.
KBIA0119E
Stamp mark
Thickness
INT
EXH
788U
788R
788V
7.88 mm
790U
790R
790V
7.90 mm
·
·
·
·
·
·
·
·
840U
840R
840V
8.40 mm
OIL SEAL
EM-93
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2006 August
2006 Murano
OIL SEAL
PFP:00100
Removal and Installation of Valve Oil Seal
NBS0029P
REMOVAL
1.
Remove engine assembly from the vehicle, and separate front suspension member, transaxle and trans-
fer (AWD models) assembly from engine. Refer to
.
2.
Install engine sub-attachment with engine stand shaft [SST: KV10117001 (
—
) and KV10106500 (
—
)] to right side of cylinder block, then lift engine, and mount it onto engine stand [SST: ST0501S000
(
—
)]. Refer to
.
3.
Remove camshaft relating to valve oil seal to be removed. Refer to
.
4.
Remove valve lifters. Refer to
5.
Turn crankshaft until the cylinder requiring new oil seals is at TDC. This will prevent valve from dropping
into cylinder.
6.
Remove valve collet.
●
Compress valve spring with the valve spring compressor, the
attachment, the adapter (SST). Remove valve collet with a
magnet hand.
CAUTION:
When working, take care not to damage valve lifter holes.
7.
Remove valve spring retainer and valve spring.
8.
Remove valve oil seal using the valve oil seal puller (SST).
INSTALLATION
1.
Apply new engine oil on new valve oil seal joint and seal lip.
2.
Using the valve oil seal drift (SST), press fit valve seal to height
“H” shown in figure.
NOTE:
Dimension “H”: Height measured before valve spring seat instal-
lation
3.
Install in the reverse order of removal after this step.
PBIC1803E
PBIC0884E
Intake and exhaust
: 14.3 - 14.9 mm (0.563 - 0.587 in)
PBIC2769E
EM-94
OIL SEAL
Revision: 2006 August
2006 Murano
Removal and Installation of Front Oil Seal
NBS0029Q
REMOVAL
1.
Remove the following parts:
●
Right side front road wheel and tire
●
Splash guard (RH)
●
Drive belts: Refer to
.
●
Crankshaft pulley: Refer to
2.
Remove front oil seal using a suitable tool.
CAUTION:
Be careful not to damage front timing chain case and crank-
shaft.
INSTALLATION
1.
Apply new engine oil to both oil seal lip and dust seal lip of new front oil seal.
2.
Install front oil seal.
●
Install front oil seal so that each seal lip is oriented as shown
in the figure.
●
Using a suitable drift, press-fit until the height of front oil seal
is level with the mounting surface.
–
Suitable drift: outer diameter 60 mm (2.36 in), inner diameter
50 mm (1.97 in).
CAUTION:
●
Be careful not to damage front timing chain case and
crankshaft.
●
Press-fit straight and avoid causing burrs or tilting oil
seal.
3.
Install in the reverse order of removal after this step.
Removal and Installation of Rear Oil Seal
NBS0029R
REMOVAL
1.
Remove engine assembly from the vehicle, and separate front suspension member, transaxle and trans-
fer (AWD models) assembly from engine. Refer to
.
2.
Install engine sub-attachment with engine stand shaft [SST: KV10117001 (
—
) and KV10106500 (
—
)] to right side of cylinder block, then lift engine, and mount it onto engine stand [SST: ST0501S000
(
—
)]. Refer to
3.
Remove drive plate. Refer to
.
4.
Remove oil pan (upper). Refer to
EM-29, "OIL PAN AND OIL STRAINER"
SEM829E
SEM715A
SEM829E
OIL SEAL
EM-95
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2006 August
2006 Murano
5.
Use a seal cutter (SST) to cut away liquid gasket and remove
rear oil seal retainer.
CAUTION:
Be careful not to damage mating surfaces.
NOTE:
Regard both rear oil seal and retainer a an assembly.
INSTALLATION
1.
Remove old liquid gasket on mating surfaces of cylinder block and oil pan (upper) using a scraper.
2.
Apply new engine oil to both oil seal lip and dust seal lip of new rear oil seal retainer.
3.
Apply a continuous bead of liquid gasket with the tube presser
[SST: WS39930000 (
—
)] to rear oil seal retainer as shown
in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS"
.
CAUTION:
Attaching should be done within 5 minutes after coating.
4.
Install rear oil seal retainer to cylinder block. Refer to
●
Make sure the garter spring is in position and seal lips not inverted.
5.
Install in the reverse order of removal after this step.
SEM830E
PBIC2661E
EM-96
CYLINDER HEAD
Revision: 2006 August
2006 Murano
CYLINDER HEAD
PFP:11041
On-Vehicle Service
NBS0029S
CHECKING COMPRESSION PRESSURE
1.
Warm up engine thoroughly. Then, stop it.
2.
Release fuel pressure. Refer to
EC-78, "FUEL PRESSURE RELEASE"
3.
Disconnect fuel pump fuse to avoid fuel injection during mea-
surement.
4.
Remove engine cover. Refer to
EM-18, "INTAKE MANIFOLD COLLECTOR"
.
5.
Remove ignition coil and spark plug from each cylinder. Refer to
"SPARK PLUG (PLATINUM-TIPPED TYPE)"
6.
Connect engine tachometer (not required in use of CONSULT-ll).
7.
Install compression tester (commercial service tool) with adapter
onto spark plug hole.
●
Use compression gauge whose picking up end inserted to
spark plug hole is smaller than 20 mm (0.79 in) in diameter.
Otherwise, it may be caught by cylinder head during removal.
8.
With accelerator pedal fully depressed, turn ignition switch to “START” for cranking. When the gauge
pointer stabilizes, read the compression pressure and engine rpm. Perform these steps to check each cyl-
inder.
Compression pressure:
Unit: kPa (kg/cm
2
, psi) /rpm
CAUTION:
Always use a fully changed battery to obtain specified engine speed.
PBIB1375E
PBIC1186E
SBIA0533E
Standard
Minimum
Deference limit between cylinders
1,275 (13.0, 185)/300
981 (10.0, 142)/300
98 (1.0, 14)/300
CYLINDER HEAD
EM-97
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2006 August
2006 Murano
●
If the engine speed is out of the specified range, check battery liquid for proper gravity. Check the
engine speed again with normal battery gravity.
●
If compression pressure is below minimum value, check valve clearances and parts associated with
combustion chamber (valve, valve seat, piston, piston ring, cylinder bore, cylinder head, cylinder head
gasket). After the checking, measure compression pressure again.
●
If some cylinders have low compression pressure, pour small amount of engine oil into spark plug hole
of cylinder to re-check it for compression.
–
If the added engine oil improves the compression, piston rings may be worn out or damaged. Check
piston rings and replace if necessary.
–
If the compression pressure remains at low level despite the addition of engine oil, valves may be mal-
functioning. Check valves for damage. Replace valve or valve seat accordingly.
●
If two adjacent cylinders have respectively low compression pressure and their compression remains
low even after the addition of engine oil, cylinder head gaskets are leaking. In such a case, replace cyl-
inder head gaskets.
9.
After inspection is completed, install removed parts.
10. Start the engine, and make sure that the engine runs smoothly.
11. Perform trouble diagnosis. If DTC appears, erase it. Refer to
.
Removal and Installation
NBS0029T
●
Refer to
for symbol marks in the figure.
REMOVAL
1.
Remove engine assembly from the vehicle, and separate front suspension member and transaxle from
engine. Refer to
1.
Cylinder head (left bank)
2.
Cylinder head bolt
3.
Cylinder head (right bank)
4.
Cylinder head gasket (right bank)
5.
Cylinder head gasket (left bank)
6.
Oil level gauge
A.
PBIC4188E
EM-98
CYLINDER HEAD
Revision: 2006 August
2006 Murano
2.
Install engine sub-attachment with engine stand shaft [SST: KV10117001 (
—
) and KV10106500 (
—
)] to right side of cylinder block, then lift engine, and mount it onto engine stand [SST: ST0501S000
(
—
)]. Refer to
3.
Remove camshaft. Refer to
.
4.
Remove engine slingers.
5.
Remove the following parts:
●
Fuel tube and fuel injector assembly: Refer to
EM-41, "FUEL INJECTOR AND FUEL TUBE"
●
Intake manifold: Refer to
●
Exhaust manifold: Refer to
EM-25, "EXHAUST MANIFOLD AND THREE WAY CATALYST"
●
Water inlet and thermostat assembly: Refer to
CO-27, "WATER INLET AND THERMOSTAT ASSEM-
●
Water outlet, water bypass pipe, heater pipe and water connector: Refer to
6.
Remove cylinder head bolts in reverse order as shown in the fig-
ure with cylinder head bolt wrench (commercial service tool) to
remove cylinder heads (right and left banks).
7.
Remove cylinder head gaskets.
INSPECTION AFTER REMOVAL
Cylinder Head Bolts Outer Diameter
●
Cylinder head bolts are tightened by plastic zone tightening
method. Whenever the size difference between “d1” and “d2”
exceeds the limit, replace them with new one.
●
If reduction of outer diameter appears in a position other than
“d2”, use it as “d2” point.
PBIC2057E
Limit (“d1” – “d2”)
: 0.11 mm (0.0043 in)
PBIC2480E
CYLINDER HEAD
EM-99
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2006 August
2006 Murano
Cylinder Head Distortion
NOTE:
When performing this inspection, cylinder block distortion should be also checking. Refer to
.
1.
Using a scraper, wipe off oil, scale, gasket, sealant and carbon deposits from surface of cylinder head.
CAUTION:
Do not allow gasket fragments to enter engine oil or engine coolant passages.
2.
At each of several locations on bottom surface of cylinder head,
measure the distortion in six directions.
●
If it exceeds the limit, replace cylinder head.
INSTALLATION
1.
Install new cylinder head gaskets.
2.
Turn crankshaft until No. 1 piston is set at TDC.
●
Crankshaft key should line up with the right bank cylinder cen-
ter line as shown in the figure.
3.
Install cylinder head follow the steps below to tighten cylinder
head bolts in numerical order as shown in the figure with cylin-
der head bolts wrench (commercial service tool).
CAUTION:
If cylinder head bolts re-used, check their outer diameters
before installation. Refer to
a.
Apply new engine oil to threads and seat surfaces of cylinder
head bolts.
b.
Tighten all cylinder head bolts.
c.
Completely loosen all cylinder head bolts.
CAUTION:
In step “c”, loosen bolts in reverse order of that indicated in
the figure.
d.
Tighten all cylinder head bolts.
Limit
: 0.1 mm (0.004 in)
SEM861E
SEM532G
: 98.1 N·m (10 kg-m, 72 ft-lb)
: 0 N·m (0 kg-m, 0 ft-lb)
: 39.2 N·m (4.0 kg-m, 29 ft-lb)
PBIC2057E
EM-100
CYLINDER HEAD
Revision: 2006 August
2006 Murano
e.
Turn all cylinder head bolts 90 degrees clockwise. (Angle tight-
ening)
CAUTION:
Check the tightening angle by using the angle wrench
(SST). Avoid judgment by visual inspection without tool.
●
Check tightening angle indicated on the angle wrench indica-
tor plate.
f.
Turn all cylinder head bolts 90 degrees clockwise again. (Angle
tightening)
4.
After installing cylinder head, measure distance between front
end faces of cylinder block and cylinder head (left and right
banks).
●
If the measured value is out of the standard, re-install cylinder
head.
5.
Install in the reverse order of removal after this step.
INSPECTION AFTER INSTALLATION
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.
●
Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-10, "RECOMMENDED FLUIDS AND LUBRICANTS"
●
Use procedure below to check for fuel leakage.
–
Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
–
Start engine. With engine speed increased, check again for fuel leakage at connection points.
●
Run engine to check for unusual noise and vibration.
●
Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.
●
Bleed air from lines and hoses of applicable lines, such as in cooling system.
●
After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.
PBIC0888E
Standard
: 14.1 - 14.9 mm (0.555 - 0.587 in)
EMQ0662D
Items
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Other oils and fluid*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gases
—
Leakage
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст