Nissan Murano Z50 (2006 year). Manual — part 132
FL-1
FUEL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION
A
FL
Revision: 2006 August
2006 Murano
FUEL SYSTEM
PREPARATION . . . . . . . . . . . . . . ... 2
Special Service Tools . . . . . . . . . . . ... 2
Commercial Service Tools . . . . . . . . . . 2
FUEL SYSTEM . . . . . . . . . . . . . . ... 3
Checking Fuel Lines . . . . . . . . . . . . . 3
General Precautions . . . . . . . . . . . . 3
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND
FUEL PUMP ASSEMBLY . . . . . . . . . . ... 4
Components . . . . . . . . . . . . . . . . 4
Removal and Installation . . . . . . . . . . .. 4
Components . . . . . . . . . . . . . . . . 8
Disassembly and Assembly . . . . . . . . . .. 9
DISASSEMBLY . . . . . . . . . . . . . . 9
ASSEMBLY . . . . . . . . . . . . . . ... 9
FUEL TANK . . . . . . . . . . . . . . . .. 10
Removal and Installation . . . . . . . . . . 10
SERVICE DATA AND SPECIFICATIONS (SDS) . .. 13
FL-2
PREPARATION
Revision: 2006 August
2006 Murano
PREPARATION
PFP:00002
Special Service Tools
NBS002RM
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
NBS002RN
(Kent-Moore No.)
Tool name
Description
(J-46211)
Fuel tank lock ring wrench
Removing and installing fuel tank retainer
SBIA0388E
Tool name
Description
Power tool
Loosening nuts and bolts
PBIC0190E
FUEL SYSTEM
FL-3
C
D
E
F
G
H
I
J
K
L
M
A
FL
Revision: 2006 August
2006 Murano
FUEL SYSTEM
PFP:17503
Checking Fuel Lines
NBS002RO
Inspect fuel lines, fuel filler cap and fuel tank for improper attach-
ment, leaks, cracks, damage, loose connections, chafing or deterio-
ration.
If necessary, repair or replace damaged parts.
General Precautions
NBS002RP
WARNING:
When replacing fuel line parts, be sure to observe the following.
●
Put a “CAUTION: FLAMMABLE” sign in the workshop.
●
Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
●
Do not smoke while servicing fuel system. Keep open flames and sparks away from the work area.
●
Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in
safe area.
CAUTION:
●
Use gasoline required by the regulations for octane number. Refer to
(Unleaded Premium Gasoline Recommended)"
●
Before removing fuel line parts, carry out the following procedures:
–
Release fuel pressure from the fuel lines. Refer to
EC-78, "FUEL PRESSURE RELEASE"
–
Disconnect negative battery terminal.
●
Always replace O-rings and clamps with new ones.
●
Do not kink or twist tubes when they are being installed.
●
After connecting fuel tube quick connectors, make sure
quick connectors are secure.
Ensure that connector and resin tube do not contact any
adjacent parts.
●
After installing tubes, make sure there is no fuel leakage at
connections in the following steps.
–
Apply fuel pressure to fuel lines with turning ignition switch
“ON” (with engine stopped). Then check for fuel leaks at
connections.
–
Start engine and rev it up and check for fuel leaks at con-
nections.
●
Use only a genuine NISSAN fuel filler cap as a replacement.
If an incorrect fuel filler cap is used, the “MIL” may come
on.
●
For servicing “Evaporative Emission System” parts, refer to
EC-30, "EVAPORATIVE EMISSION SYSTEM"
●
For servicing “On Board Refueling Vapor Recovery
(ORVR)” parts, refer to
.
SMA803A
SBIA0504E
FL-4
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Revision: 2006 August
2006 Murano
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
PFP:17042
Components
NBS006T5
Removal and Installation
NBS002RQ
REMOVAL
WARNING:
Read “General Precautions” before working on the fuel system. Refer to
.
1.
Check fuel level on fuel gauge. If fuel gauge indicates more than
the level as shown in the figure (full or almost full), drain fuel
from fuel tank until fuel gauge indicates level as shown in the fig-
ure or below.
NOTE:
Because fuel will be spilled when removing fuel level sensor unit
for the top of fuel is above the fuel level sensor unit installation
surface.
●
As a guide, fuel level becomes the position as shown in the
figure or below when approximately 20 (5-1/4 US gal, 4-3/8
Imp gal) of fuel are drained from fuel tank.
●
In a case that fuel pump does not operate, perform the follow-
ing procedure.
a.
Insert hose of less than 25 mm (0.98 in) in diameter into fuel filler tube through fuel filler opening to draw
fuel from fuel filler tube.
b.
Disconnect fuel filler hose from fuel filler tube. Refer to
c.
Insert hose into fuel tank through fuel filler hose to draw fuel from fuel tank.
2.
Release the fuel pressure from the fuel lines. Refer to
EC-78, "FUEL PRESSURE RELEASE"
3.
Open fuel filler lid.
4.
Open fuel filler cap and release the pressure inside fuel tank.
5.
Remove rear seat cushion trim and pad bolts, then lift up rear seat cushion. Refer to
1.
Retainer
2.
Sub fuel level sensor unit
3.
O-ring
4.
Main fuel level sensor unit, fuel filter
and fuel pump assembly
SBIA0392E
SBIA0393E
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-5
C
D
E
F
G
H
I
J
K
L
M
A
FL
Revision: 2006 August
2006 Murano
6.
Remove inspection hole cover for main and sub fuel level sen-
sor unit by turning clips counterclockwise by 90 degrees and by
mating both cover hole and clip shape.
7.
Disconnect harness connector and quick connectors for EVAP
hose and fuel feed tube
Disconnect quick connector as follows:
●
Hold the sides of quick connector, push in tabs and pull out
fuel feed tube.
●
If quick connector sticks to tube of fuel level sensor unit, push
and pull quick connector several times until it start to
move.Then disconnect quick connector by pulling.
SBIA0394E
PBIC1807E
SFE562A
FL-6
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Revision: 2006 August
2006 Murano
CAUTION:
●
Quick connector can be disconnected when the tabs
are completely depressed. Do not twist it more than
necessary.
●
Do not use any tools to disconnected quick connector.
●
Keep resin tube away from heat. Be especially careful
when welding near the resin tube.
●
Prevent acid liquid such as battery electrolyte, etc.
from getting on resin tube.
●
Do not bend or twist resin tube during installation and
disconnection.
●
Do not remove the remaining retainer on hard tube (or
the equivalent) except when resin tube or retainer is
replaced.
●
When resin tube or hard tube (or the equivalent) is
replaced, also replace retainer with new one.
●
Replace same color retainer as before replacing.
●
To keep the connecting portion clean and to avoid
damage and foreign materials, cover them completely
with plastic bags or something similar.
8.
Remove retainer for main and sub fuel level sensor unit with fuel
tank lock ring wrench (SST) by turning counterclockwise.
9.
Remove main fuel level sensor unit, fuel filter and fuel pump
assembly, and sub fuel level sensor unit.
●
Raise main fuel level sensor unit, fuel filter and fuel pump
assembly, and disconnect fuel hose connector (push in tabs
and pull out) and sub fuel level sensor unit harness connector.
●
Raise and release sub fuel level sensor unit to remove.
Retainer color: Green
SBIA0504E
PBIC0163E
SBIA0411E
SBIA0396E
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-7
C
D
E
F
G
H
I
J
K
L
M
A
FL
Revision: 2006 August
2006 Murano
INSTALLATION
Note the following, and install in the reverse order of removal.
Main and Sub Fuel Level Sensor Unit
1.
Install new O-rings to fuel tank without any twist.
2.
Connect fuel hose connector (push in until it stops) and sub fuel
level sensor unit harness connector.
NOTE:
When installing fuel hose connector insert them fully until a click
sound of full stopper engagement is heard.
3.
Align the direction mark on main and sub fuel level sensor unit
with that on fuel tank as shown in the figure, and install them to
fuel tank.
CAUTION:
●
Do not allow O-ring to drop.
●
Do not bend float arm during installing.
4.
Install retainer for main and sub fuel level sensor unit with fuel
tank lock ring wrench (SST) by turning clockwise.
CAUTION:
Install retainer horizontally.
Quick Connector
Connect quick connector as follows:
1.
Check the connection for damage or any foreign materials.
2.
Align the connector with the tube, then insert the connector straight into the tube until a click sound is
heard.
3.
After connecting, make sure that the connection is secure by following method.
●
Visually confirm that the two tabs are connected to the connector.
SBIA0398E
SBIA0397E
SBIA0411E
FL-8
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Revision: 2006 August
2006 Murano
●
Pull the tube and the connector to make sure they are
securely connected.
Inspection Hole Cover
1.
Install inspection hole cover with front mark (arrow) facing front
of vehicle (Both RH and LH).
2.
Lock clips by turning clockwise.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1.
Turn ignition switch “ON” (with engine stopped), then check connections for leaks by applying fuel pres-
sure to fuel piping.
2.
Start engine and rev it up and make sure there are no fuel leaks at the fuel system connections.
Components
NBS006T6
PBIC1653E
SBIA0479E
1.
Sub fuel level sensor unit
2.
Sub fuel level sensor unit base
3.
Fuel filter and fuel pump assembly
4.
Fuel level sensor unit
: Vehicle front
PBIC4901J
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-9
C
D
E
F
G
H
I
J
K
L
M
A
FL
Revision: 2006 August
2006 Murano
Disassembly and Assembly
NBS006T7
DISASSEMBLY
Fuel level sensor unit, fuel filter and fuel pump assembly side
1.
Disconnect harness connector.
2.
Remove fuel level sensor unit (1) according to the following pro-
cedure.
a.
Push the pawl of fuel level sensor unit mounting area with an L-
shaped iron rod or an equivalent to unlock.
CAUTION:
Be careful not to damage it.
b.
With the fuel level sensor unit unlocked, slide it in the direction
shown by the arrow (
).
Sub fuel level sensor unit assembly side
1.
Remove sub fuel level sensor unit (1) according to the following
procedure.
a.
Push the pawl of sub fuel level sensor unit mounting area with
an L-shaped iron rod or an equivalent to unlock.
CAUTION:
Be careful not to damage it.
b.
With the sub fuel level sensor unit unlocked, slide it in the direc-
tion shown by the arrow (
).
ASSEMBLY
Install fuel level sensor unit and sub fuel level sensor unit according to the following procedure.
●
Insert fuel level sensor unit and sub fuel level sensor unit all the way to the end until a “click” touch and
sound can be recognized.
●
Pull fuel level sensor unit and sub fuel level sensor unit in the removal direction to ensure that they do not
become detached.
PBIC4900J
PBIC4899J
FL-10
FUEL TANK
Revision: 2006 August
2006 Murano
FUEL TANK
PFP:17202
Removal and Installation
NBS002RR
REMOVAL
WARNING:
Be sure to read “General Precautions” when working on fuel system. Refer to
●
Drain fuel from fuel tank if necessary. Refer to
CAUTION:
For the safety work and to maintain fuel tank gravity at center, drain fuel to the level where fuel
tank weight at left and right becomes equal.
●
Perform work on level place.
1.
Perform steps 2 to 7 of “REMOVAL” in “FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP
ASSEMBLY”. Refer to
2.
Remove center muffler. Refer to
.
3.
Remove rear propeller shaft (AWD models). Refer to
4.
Remove parking brake cables. Refer to
5.
Remove rear final drive assembly (AWD models).
●
Using a transmission jack, support the bottom of the rear final drive assembly. Refer to
6.
Remove mounting nuts on the rear suspension member, and lower the transmission jack carefully until
just before rear suspension member is removed from stud bolts on the vehicle (AWD models). Refer to
RSU-5, "REAR SUSPENSION ASSEMBLY"
.
7.
Remove fuel tank protector.
1.
Fuel filler cap
2.
Grommet
3.
Fuel filler tube
4.
Hose clamp
5.
Fuel filler hose
6.
Hose clamp
7.
EVAP/Vent line hose
8.
Hose clamp
9.
EVAP (Recirculation) hose
10. Fuel tank
11. Fuel tank protector
12. Fuel tank mounting band
SBIA0399E
FUEL TANK
FL-11
C
D
E
F
G
H
I
J
K
L
M
A
FL
Revision: 2006 August
2006 Murano
8.
Disconnect fuel filler hose, EVAP/Vent line hose and EVAP
(Recirculation) hose at the other end than fuel tank side.
9.
Support the lower part of fuel tank with transmission jack.
CAUTION:
Support the position that fuel tank mounting bands do not
engage.
10. Remove fuel tank mounting bands.
11. Supporting with hands, descend transmission jack carefully, and remove fuel tank.
CAUTION:
●
Make sure that all connection points have been disconnected.
●
Confirm there is no interference with vehicle.
12. Remove fuel filler tube, if necessary.
INSTALLATION
Note the following, and install in the reverse order of removal.
●
Surely clamp fuel hoses and insert hose to the length below.
●
Be sure hose clamp is not placed on swelled area of fuel tube.
●
Tighten fuel hose clamp so that the distance between its lugs becomes to the following.
●
Push the fuel tank mounting band pin to the vehicle side securely.
●
Before fixing the fuel tank, temporarily install the filler tube.
SBIA0401E
SBIA0402E
Fuel filler hose
: 35 mm (1.38 in)
The other hoses
: 25 mm (0.98 in)
Fuel tank side
: 2 - 6 mm (0.08 - 0.24 in)
Fuel filler tube side
: 5 - 9 mm (0.20 - 0.35 in)
FL-12
FUEL TANK
Revision: 2006 August
2006 Murano
CAUTION:
Use genuine fuel filler tube mounting bolts or equivalent. Make sure to tighten them to the speci-
fied torque.
●
To connect the quick connector, refer to
INSPECTION AFTER INSTALLATION
Make sure there is no fuel leakage at connections in the following steps.
1.
Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pres-
sure to fuel piping.
2.
Start engine and rev it up and make sure there are no fuel leaks at the fuel system tube and hose connec-
tions.
●
After removing/installing rear suspension assembly, make sure to adjust wheel alignment and then, adjust
neutral position of steering angle sensor. Refer to
RSU-5, "Wheel Alignment Inspection"
and
SERVICE DATA AND SPECIFICATIONS (SDS)
FL-13
C
D
E
F
G
H
I
J
K
L
M
A
FL
Revision: 2006 August
2006 Murano
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Standard and Limit
NBS002RS
FUEL TANK
Fuel tank capacity
Approx. 82 (21-5/8 US gal, 18 Imp gal)
Fuel recommendation
Refer to
FL-14
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2006 August
2006 Murano
FSU-1
FRONT SUSPENSION
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION
A
B
FSU
Revision: 2006 August
2006 Murano
FRONT SUSPENSION
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Caution . . . . . . . . . . . . . . . . . . 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools (SST) . . . . . . . . . . 3
Commercial Service Tools . . . . . . . . . . 3
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 4
NVH Troubleshooting Chart . . . . . . . . . . 4
FRONT SUSPENSION ASSEMBLY . . . . . . ... 5
On-Vehicle Inspection . . . . . . . . . . . .. 5
Wheel Alignment Inspection . . . . . . . . . . 5
Components . . . . . . . . . . . . . . . . 7
Removal and Installation . . . . . . . . . . .. 8
COIL SPRING AND STRUT . . . . . . . . . ... 9
Removal and Installation . . . . . . . . . . .. 9
REMOVAL . . . . . . . . . . . . . . . . 9
INSTALLATION . . . . . . . . . . . . . . 9
Disassembly and Assembly . . . . . . . . . .. 9
TRANSVERSE LINK . . . . . . . . . . . . . 12
Removal and Installation . . . . . . . . . . 12
STABILIZER BAR . . . . . . . . . . . . . . 14
Removal and Installation . . . . . . . . . . 14
FRONT SUSPENSION MEMBER . . . . . . . . 15
Removal and Installation . . . . . . . . . . 15
FSU-2
PRECAUTIONS
Revision: 2006 August
2006 Murano
PRECAUTIONS
PFP:00001
Caution
NES00085
●
When installing rubber bushings, final tightening must be carried out under unladen conditions with tires
on ground. Oil will shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
●
Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
●
After servicing suspension parts, be sure to check wheel alignment.
●
Caulking nuts are not reusable. Always use new ones when installing. Since new caulking nuts are pre-
oiled, tighten as they are.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст