Nissan Murano Z50 (2006 year). Manual — part 15
AUDIO
AV-53
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2006 August
2006 Murano
Inspection of Rear Door Speaker (BOSE System)
NKS00222
1.
CHECK HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect BOSE speaker amp. and rear door speaker connectors.
3.
Check continuity between BOSE speaker amp. harness connec-
tor terminals and rear door speaker harness connector termi-
nals.
4.
Check continuity between BOSE speaker amp. harness connec-
tor terminals and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair harness or connector.
Terminals
Continuity
BOSE speaker amp.
Rear door speaker
Connector
Terminal
Connector
Terminal
B115
9
D53
1
Yes
10
2
11
D73
1
12
2
Terminals
Continuity
BOSE speaker amp.
Ground
Connector
Terminal
B115
9
No
10
11
12
SKIA4313E
AV-54
AUDIO
Revision: 2006 August
2006 Murano
2.
CHECK REAR DOOR SPEAKER SIGNAL
1.
Connect BOSE speaker amp. and rear door speaker connectors.
2.
Turn ignition switch ON.
3.
Press “POWER” switch.
4.
Check voltage waveform BOSE speaker amp. harness connec-
tor terminals with CONSULT-II or oscilloscope.
OK or NG
OK
>> Replace rear door speaker.
NG
>> GO TO 3.
Terminals
Condi-
tion
Reference value
(+)
(–)
Con-
nector
Termi-
nal
Con-
nec-
tor
Termi-
nal
B115
9
B115
10
Receive
audio
signal
11
12
SKIB0456E
SKIB3609E
AUDIO
AV-55
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2006 August
2006 Murano
3.
CHECK HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect audio unit and BOSE speaker amp. connectors.
3.
Check continuity between audio unit harness connector termi-
nals and BOSE speaker amp. harness connector terminals.
4.
Check continuity between audio unit harness connector termi-
nals and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair harness or connector.
Terminals
Continuity
Audio unit
BOSE speaker amp.
Connector
Terminal
Connector
Terminal
M45
13
B115
25
Yes
14
26
15
23
16
24
Terminals
Continuity
Audio unit
Ground
Connector
Terminal
M45
13
No
14
15
16
SKIA4315E
AV-56
AUDIO
Revision: 2006 August
2006 Murano
4.
CHECK REAR DOOR SPEAKER SIGNAL
1.
Connect audio unit and BOSE speaker amp. connectors.
2.
Turn ignition switch ON.
3.
Press “POWER” switch.
4.
Check voltage waveform audio unit harness connector terminals
with CONSULT-II or oscilloscope.
OK or NG
OK
>> INSPECTION END
NG
>> Replace audio unit.
Terminals
Condi-
tion
Reference value
(+)
(–)
Con-
nector
Termi-
nal
Con-
nector
Termi-
nal
M45
14
M45
13
Receive
audio
signal
16
15
SKIA9402E
SKIB3609E
AUDIO
AV-57
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2006 August
2006 Murano
Inspection of Woofer (BOSE System)
NKS00223
1.
CHECK HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect BOSE speaker amp. and woofer connectors.
3.
Check continuity between BOSE speaker amp. harness connec-
tor terminals and woofer harness connector harness connector
terminals.
4.
Check continuity between BOSE speaker amp, harness connector terminals and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair harness or connector.
Terminals
Continuity
BOSE speaker amp.
Woofer
Connector
Terminal
Connector
Terminal
B114
2
B28
3
Yes
3
4
18
2
19
6
Terminals
Continuity
BOSE speaker amp.
Ground
Connector
Terminal
B114
2
No
3
18
19
SKIB0530E
AV-58
AUDIO
Revision: 2006 August
2006 Murano
2.
CHECK WOOFER SIGNAL
1.
Connect BOSE speaker amp. and woofer connectors.
2.
Turn ignition switch ON.
3.
Press “POWER” switch.
4.
Check voltage waveform BOSE speaker amp. harness connec-
tor terminals with CONSULT-II or oscilloscope.
OK or NG
OK
>> INSPECTION END
NG
>> Replace BOSE speaker amp.
Terminals
Condi-
tion
Reference value
(+)
(–)
Con-
nec-
tor
Ter-
minal
Con-
nec-
tor
Ter-
minal
B114
18
B114
2
Receive
audio
signal
19 3
SKIA9407E
SKIB3609E
AUDIO
AV-59
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2006 August
2006 Murano
Locking CD Auto Changer Mechanism
NKS00225
CAUTION:
●
Prior to removing a malfunctioning CD auto changer unit that will be shipped for repair, the
changer mechanism MUST BE LOCKED to prevent the mechanism from being damaged during
shipping.
●
If a CD is jammed or unable to be removed from the unit, do NOT lock the changer mechanism. If
the unit is to be shipped for repair, carefully package the unit to prevent vibration and shock.
DAMPER LOCK PROCEDURE
1.
Eject and remove any CDs from CD auto changer unit.
2.
Turn ignition switch OFF. Wait until CD auto changer unit display is OFF and mechanism stops moving
(mechanism sound stops).
3.
Press any one of the disc selection buttons once. When a display shows on the CD auto changer unit,
press the same disc selection button again within 5 seconds.
●
The changer mechanism will lock itself within 10 seconds.
4.
After mechanism stops moving (mechanism sound stops), disconnect the battery cable from the negative
terminal.
NOTE:
After installing a new or remanufactured CD auto changer unit, switching the CD auto changer unit ON will
automatically unlock the mechanism. A special unlocking procedure is not required.
Removal and Installation of Audio Unit
NKS00226
REMOVAL
1.
Perform damper lock operation (BOSE system). Refer to
AV-59, "Locking CD Auto Changer Mechanism"
2.
Remove center ventilator. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
.
3.
Remove instrument stay cover (LH/RH). Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
4.
Remove screws (2).
5.
Remove screws (4).
6.
Remove cluster lid C and audio unit.
PKIA2447E
PKIA2443E
AV-60
AUDIO
Revision: 2006 August
2006 Murano
7.
Unlock FPC (Flexible Print Circuit) connector lock on A/C and
AV switch side.
8.
Pull off flexible printed circuit from connector.
CAUTION:
Make sure mating surface of FPC (Flexible Print Circuit) and
the direction of connector terminal.
9.
Remove screws (4) and clips (2), and remove audio unit from
cluster lid C.
10. Remove audio unit screws (8), unified meter and A/C amp.
screws (2), and remove brackets.
CAUTION:
●
When carrying audio unit body, do not touch internal
mechanism access from cassette tape slot.
●
Be careful not to allow foreign material to enter from cas-
sette tape slot.
●
Use appropriate screws for each, as screws for audio unit
are different from that for unified meter and A/C amp.
INSTALLATION
Installation is the reverse order of removal.
PKIA2444E
PKIA2448E
PKIA2449E
AUDIO
AV-61
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2006 August
2006 Murano
Removal and Installation for A/C and AV Switch
NKS00227
REMOVAL
1.
Remove audio unit from cluster lid C. Refer to
AV-59, "Removal and Installation of Audio Unit"
2.
Remove screws (8), and remove A/C and AV switch.
INSTALLATION
Installation is the reverse order of removal.
PKIA2452E
1.
Front finisher
2.
A/C and AV switch
3.
Screws
4.
Screws
5.
Cluster lid C
PKIA2451E
AV-62
AUDIO
Revision: 2006 August
2006 Murano
Removal and Installation of Audio Steering Switch
NKS00228
REMOVAL
1.
Remove steering wheel. Refer to
PS-10, "Removal and Installation"
2.
Remove steering wheel cover.
3.
Remove screws (2), and remove audio steering switch.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Front Door Speaker (Base System)
NKS00229
REMOVAL
1.
Remove door finisher. Refer to
2.
Remove screws (4), and remove speaker.
3.
Remove screws (4), and remove bracket.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Front Door Speaker (BOSE System)
NKS0022A
REMOVAL
1.
Remove door finisher. Refer to
2.
Remove screws (3), and remove speaker.
3.
Remove screws (3), and remove bracket.
INSTALLATION
Installation is the reverse order of removal.
SKIB0039E
PKIA2454E
PKIA2455E
AUDIO
AV-63
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2006 August
2006 Murano
Removal and Installation of Rear Door Speaker (Base System)
NKS0022B
REMOVAL
1.
Remove door finisher. Refer to
2.
Remove screws (3), and remove speaker.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Rear Door Speaker (BOSE System)
NKS0022C
REMOVAL
1.
Remove door finisher. Refer to
2.
Remove screws (3), and remove speaker.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Tweeter
NKS0022D
REMOVAL
1.
Remove side ventilator assembly. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
.
2.
Remove instrument side finisher. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
3.
Remove screws (2), and remove tweeter.
INSTALLATION
Installation is the reverse order of removal.
PKIA2456E
PKIA2457E
PKIA2458E
AV-64
AUDIO
Revision: 2006 August
2006 Murano
Removal and Installation of Woofer
NKS0022E
REMOVAL
1.
Open luggage floor finisher (center). Refer to
2.
Remove woofer clamp, and disconnect woofer connector.
3.
Remove woofer.
CAUTION:
Connectors must be placed in the left side, when installed.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of BOSE Speaker Amp.
NKS0022F
REMOVAL
1.
Remove luggage floor finisher (front). Refer to
2.
Remove screws (4) and connectors (2), and remove BOSE
speaker amp. from luggage floor.
3.
Remove screws (4), and remove bracket.
INSTALLATION
Installation is the reverse order of removal.
PKIA2459E
PKIA2460E
PKIA2461E
AUDIO
AV-65
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2006 August
2006 Murano
Removal and Installation of Satellite Radio Tuner
NKS002LZ
: Vehicle front
REMOVAL
1.
Remove luggage floor finisher (front). Refer to
.
2.
Remove screws (A) and connectors (1), and remove satellite
radio tuner (2) from luggage floor.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Satellite Radio Antenna
NKS002MN
: Vehicle front
REMOVAL
1.
Remove luggage side finisher. Refer to
.
2.
Remove assist grip (rear). Refer to
.
3.
Pull down headlining (1) and obtain space for work between
vehicle and headlining.
4.
Remove nut (A), and then disconnect connector (2).
5.
Remove satellite radio antenna.
INSTALLATION
Installation is the reverse order of removal.
SKIB7722E
SKIB7723E
Roof antenna mounting nut
: 6.5 N·m (0.66 kg-m, 58 in-lb)
AV-66
ANTENNA
Revision: 2006 August
2006 Murano
ANTENNA
PFP:28200
Location of Antenna
NKS0022G
RADIO ANTENNA AND GPS ANTENNA
SKIB2696E
ANTENNA
AV-67
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2006 August
2006 Murano
SATELLITE RADIO ANTENNA
SKIB7748E
AV-68
ANTENNA
Revision: 2006 August
2006 Murano
Removal and Installation of Roof Antenna
NKS0022H
REMOVAL
1.
Remove headlining. Refer to
2.
Remove nut and antenna base.
3.
Remove instrument panel. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
.
4.
Remove antenna feeder (upper) and antenna feeder (lower).
5.
Remove clips (5), and separate antenna feeder (upper) from vehicle.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Satellite Radio Antenna
NKS002M9
Refer to
AV-65, "Removal and Installation of Satellite Radio Antenna"
PKIA2463E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст