Nissan Murano Z50 (2006 year). Manual — part 200
TROUBLE DIAGNOSIS
SRS-29
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2006 August
2006 Murano
3.
Touch “TROUBLE DIAG RECORD”.
NOTE:
With “TROUBLE DIAG RECORD”, diagnosis results previously
erased by a reset operation can be displayed.
4.
Diagnostic code is displayed on “TROUBLE DIAG RECORD”.
5.
Touch “PRINT”.
6.
Compare diagnostic codes to
SRS-29, "DTC No. Index (“SELF-
DIAG [PAST]” or “TROUBLE DIAG RECORD”)"
7.
Touch “BACK” key of CONSULT-II until “SELECT SYSTEM”
appears.
8.
Turn ignition switch OFF, then turn off and disconnect CON-
SULT-II, and both battery cables.
9.
Repair the system as outlined by the “Repair order” in “Intermit-
tent Malfunction Diagnostic Code Chart”, that corresponds to the
self-diagnostic result. For replacement procedure of component
parts, refer to the Removal and Installation procedure for the appropriate component.
10. Go to , for final checking.
SRS-26, "DIAGNOSTIC PROCEDURE 3"
.
DTC No. Index (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
SRS697
SHIA0182E
Diagnostic item
Explanation
Repair order
“Recheck SRS at each replacement”
NO DTC IS
DETECTED.
When malfunction is
indicated by the “AIR
BAG” warning lamp in
User mode.
●
Low battery voltage (Less than 9V)
●
Go to
●
No malfunction is detected.
●
Go to
DRIVER AIRBAG
MODULE
[OPEN]
[B1054]
●
Driver air bag module circuit is open (including the spiral cable).
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace driver air bag module, diag-
nosis sensor unit and spiral cable.
DRIVER AIRBAG
MODULE
[VB-SHORT]
[B1055]
●
Driver air bag module circuit is shorted to a power supply circuit
(including the spiral cable).
DRIVER AIRBAG
MODULE
[GND-SHORT]
[B1056]
●
Driver air bag module circuit is shorted to ground (including the
spiral cable).
DRIVER AIRBAG
MODULE
[SHORT]
[B1057]
●
Driver air bag module circuit is shorted between lines.
SRS-30
TROUBLE DIAGNOSIS
Revision: 2006 August
2006 Murano
ASSIST A/B MODULE
[OPEN]
[B1070]
●
Front passenger air bag module circuit is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace the diagnosis sensor unit
and front passenger air bag module.
ASSIST A/B MODULE
[VB-SHORT]
[B1071]
●
Front passenger air bag module circuit is shorted to a power
supply circuit.
ASSIST A/B MODULE
[GND-SHORT]
[B1072]
●
Front passenger air bag module circuit is shorted to ground.
ASSIST A/B MODULE
[SHORT]
[B1073]
●
Front passenger air bag module circuit is shorted between lines.
CRASH ZONE SEN
[UNIT FAIL]
[B1033]
[B1034]
CRASH ZONE SEN
[COMM FAIL]
[B1035]
●
Crash zone sensor
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace crash zone sensor and diag-
nosis sensor unit.
SIDE MODULE LH
[OPEN]
[B1134]
●
Front LH side air bag module circuit is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace the diagnosis sensor unit
and LH side air bag module.
SIDE MODULE LH
[VB-SHORT]
[B1135]
●
Front LH side air bag module circuit is shorted to a power sup-
ply circuit.
SIDE MODULE LH
[GND-SHORT]
[B1136]
●
Front LH side air bag module circuit is shorted to ground.
SIDE MODULE LH
[SHORT]
[B1137]
●
Front LH side air bag module circuit is shorted between lines.
SIDE MODULE RH
[OPEN]
[B1129]
●
Front RH side air bag module circuit is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace the diagnosis sensor unit
and RH side air bag module.
SIDE MODULE RH
[VB-SHORT]
[B1130]
●
Front RH side air bag module circuit is shorted to a power sup-
ply circuit.
SIDE MODULE RH
[GND-SHORT]
[B1131]
●
Front RH side air bag module circuit is shorted to ground.
SIDE MODULE RH
[SHORT]
[B1132]
●
Front RH side air bag module circuit is shorted between lines.
SATELLITE SENS LH
[UNIT FAIL]
[B1118]
[B1119]
SATELLITE SENS LH
[COMM FAIL]
[B1120]
●
LH side air bag (Satellite) sensor
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace the diagnosis sensor unit
and LH side air bag (Satellite) sen-
sor.
Diagnostic item
Explanation
Repair order
“Recheck SRS at each replacement”
TROUBLE DIAGNOSIS
SRS-31
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2006 August
2006 Murano
SATELLITE SENS RH
[UNIT FAIL]
[B1113]
[B1114]
SATELLITE SENS RH
[COMM FAIL]
[B1115]
●
RH side air bag (Satellite) sensor
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace the diagnosis sensor unit
and RH side air bag (Satellite) sen-
sor.
PRE-TEN FRONT LH
[OPEN]
[B1086]
●
Front LH pre-tensioner circuit is open.
1. Visually check the wiring harness
connections.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace the diagnosis sensor unit
and front LH seat belt.
PRE-TEN FRONT LH
[VB-SHORT]
[B1087]
●
Front LH pre-tensioner circuit is shorted to a power supply cir-
cuit.
PRE-TEN FRONT LH
[GND-SHORT]
[B1088]
●
Front LH pre-tensioner circuit is shorted to ground.
PRE-TEN FRONT LH
[SHORT]
[B1089]
●
Front LH pre-tensioner circuit is shorted between lines.
PRE-TEN FRONT RH
[OPEN]
[B1081]
●
Front RH pre-tensioner circuit is open.
1. Visually check the wiring harness
connections.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace the diagnosis sensor unit
and front RH seat belt.
PRE-TEN FRONT RH
[VB-SHORT]
[B1082]
●
Front RH pre-tensioner circuit is shorted to a power supply cir-
cuit.
PRE-TEN FRONT RH
[GND-SHORT]
[B1083]
●
Front RH pre-tensioner circuit is shorted to ground.
PRE-TEN FRONT RH
[SHORT]
[B1084]
●
Front RH pre-tensioner circuit is shorted between lines.
CURTAIN MODULE LH
[OPEN]
[B1150]
●
LH side curtain air bag module circuit is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace the diagnosis sensor unit
and LH side curtain air bag module.
CURTAIN MODULE LH
[VB-SHORT]
[B1151]
●
LH side curtain air bag module circuit is shorted to a power sup-
ply circuits.
CURTAIN MODULE LH
[GND-SHORT]
[B1152]
●
LH side curtain air bag module circuit is shorted to ground.
CURTAIN MODULE LH
[SHORT]
[B1153]
●
LH side curtain air bag module circuit is shorted between lines.
CURTAIN MODULE RH
[OPEN]
[B1145]
●
RH side curtain air bag module circuit is open.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. If the harness check result is OK,
replace the diagnosis sensor unit
and RH side curtain air bag module.
CURTAIN MODULE RH
[VB-SHORT]
[B1146]
●
RH side curtain air bag module circuit is shorted to a power sup-
ply circuit.
CURTAIN MODULE RH
[GND-SHORT]
[B1147]
●
RH side curtain air bag module circuit is shorted to ground.
CURTAIN MODULE RH
[SHORT]
[B1148]
●
RH side curtain air bag module circuit is shorted between lines.
Diagnostic item
Explanation
Repair order
“Recheck SRS at each replacement”
SRS-32
TROUBLE DIAGNOSIS
Revision: 2006 August
2006 Murano
CONTROL UNIT
[B1001-B1015]
[B1026-B1031]
[B1042-B1047]
[B1058-B1063]
[B1074-B1079]
[B1106-B1111]
[B1122-B1127]
[B1138-B1143]
[B1202-B1207]
●
Diagnosis sensor unit is malfunctioning.
1. Visually check the wiring harness
connection.
2. Replace the diagnosis sensor unit.
PASS A/B INDCTR
CKT
[B1023]
●
Cutoff telltale circuit is open or shorted to grand or the circuits
are shorted each other.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace cutoff telltale.
4. Replace the diagnosis sensor unit.
OCCUPANT SENS C/U
[UNIT FAIL]
[B1017]
[B1020]
[B1021]
●
Trouble occurs in Occupant Classification System-CU.
●
Replace passenger side seat cush-
ion assembly.
OCCUPANT SENS
[UNIT FAIL]
[B1018]
●
Trouble occurs in Occupant Classification System-SENS.
●
Replace passenger side seat cush-
ion assembly.
BELT TENSION SENS
[UNIT FAIL]
[B1019]
●
Trouble occurs in Belt Tension sensor (BTS), circuit of BTS—
Occupant Classification System-CU, or Occupant Classification
System-CU.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace passenger side seat belt
assembly.
4. Replace the diagnosis sensor unit.
OCCUPANT SENS C/U
[COMM FAIL]
[B1022]
●
Trouble occurs in Occupant Classification System-CU, circuit of
Occupant Classification System-CU—Diagnosis Senser Unit, or
Diagnosis Sensor Unit.
1. Visually check the wiring harness
connection.
2. Replace the harness if it has visible
damage.
3. Replace passenger side seat cush-
ion assembly.
4. Replace the diagnosis sensor unit.
FRONTAL COLLISION-
DETECTION
[B1209]
●
Seat belt pre-tensioner and front air bag are deployed.
●
Go to
.
SIDE COLLISION
DETECTION
[B1210]
●
Side and curtain air bag is deployed.
●
Go to
Diagnostic item
Explanation
Repair order
“Recheck SRS at each replacement”
TROUBLE DIAGNOSIS
SRS-33
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2006 August
2006 Murano
Trouble Diagnosis without CONSULT-II
NHS0005M
DIAGNOSTIC PROCEDURE 6
Inspecting SRS Malfunctioning Parts By Using “AIR BAG” Warning Lamp — Diagnosis Mode
NOTE:
SRS will not enter Diagnosis mode if no malfunction is detected in User mode.
1.
Turn ignition switch ON.
2.
After “AIR BAG” warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
3.
Wait more than 3 seconds.
4.
Repeat the steps 1 to 3 twice. (Perform three times in all.)
5.
Turn ignition switch ON.
SRS is now in Diagnosis mode.
“AIR BAG” warning lamp operates in Diagnosis mode as follows:
WARNING LAMP FLASH CODE CHART
PHIA0532E
PHIA1233E
SHIA0028E
SRS-34
TROUBLE DIAGNOSIS
Revision: 2006 August
2006 Murano
PHIA1234E
SHIA0083E
PHIA1235E
PHIA1236E
TROUBLE DIAGNOSIS
SRS-35
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2006 August
2006 Murano
SHIA0032E
SHIA0033E
PHIA1237E
PHIA1238E
SRS-36
TROUBLE DIAGNOSIS
Revision: 2006 August
2006 Murano
PHIA1240E
PHIA1241E
PHIA1242E
PHIA1243E
TROUBLE DIAGNOSIS
SRS-37
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2006 August
2006 Murano
Trouble Diagnosis: “AIR BAG” Warning Lamp Does Not Turn OFF
NHS0005N
DIAGNOSTIC PROCEDURE 7
1.
CHECK THE DEPLOYMENT OF AIR BAG MODULE
Is air bag module deployed?
YES or NO
YES
>> Refer to
NO
>> GO TO 2.
2.
CHECK THE AIR BAG FUSE
Check 10A fuse [No.13, located in fuse block (J/B)].
Refer to
PG-3, "POWER SUPPLY ROUTING CIRCUIT"
.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
CHECK AIR BAG FUSE AGAIN
Replace “AIR BAG” fuse and turn ignition switch ON.
Does the “AIR BAG” fuse blow again?
YES
>> Repair or replace main harness.
NO
>> INSPECTION END
4.
CHECK DIAGNOSIS SENSOR UNIT
Connect CONSULT-II and touch “START”.
Is “AIR BAG” displayed on CONSULT-II?
YES or NO
YES
>> GO TO 5.
NO
>> Visually check the wiring harness connection of diagno-
sis sensor unit. If the harness connection check result is
OK, replace diagnosis sensor unit.
5.
CHECK HARNESS CONNECTION
Is harness connection between warning lamp and diagnosis sensor unit OK?
OK or NG
OK
>> Replace diagnosis sensor unit.
NG
>> Connect “AIR BAG” warning lamp and diagnosis sensor unit connector properly. If “AIR BAG”
warning lamp still does not go off, replace harness.
BCIA0030E
SRS-38
TROUBLE DIAGNOSIS
Revision: 2006 August
2006 Murano
Trouble Diagnosis: “AIR BAG” Warning Lamp Does Not Turn ON
NHS0005O
DIAGNOSTIC PROCEDURE 8
1.
CHECK METER FUSE
Check 10A fuse [No.14, located in fuse block (J/B)].
Refer to
PG-3, "POWER SUPPLY ROUTING CIRCUIT"
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
CHECK METER FUSE AGAIN
Replace 10A fuse [No.14, located in fuse block (J/B)] and turn ignition switch ON.
Does the meter fuse blow again?
YES
>> Repair or replace the related harness.
NO
>> INSPECTION END
3.
CHECK HARNESS CONNECTION BETWEEN DIAGNOSIS SENSOR UNIT AND COMBINATION
METER
Disconnect diagnosis sensor unit connector and turn ignition switch ON.
Does “AIR BAG” warning lamp turn on?
YES or NO
YES
>> Replace diagnosis sensor unit.
NO
>> Replace combination meter assembly.
DRIVER AIR BAG MODULE
SRS-39
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2006 August
2006 Murano
DRIVER AIR BAG MODULE
PFP:K8510
Removal and Installation
NHS0005P
REMOVAL
CAUTION:
●
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
●
Always work from the side of driver air bag module.
●
Do not use air tools or electric tools for servicing.
1.
Remove the side lids.
2.
Remove the left and right side special bolts (TORX bolts T30).
3.
Lift up the driver air bag module.
4.
Disconnect the air bag harness connectors, and remove the
driver air bag module.
CAUTION:
●
For installing /removing driver air bag module connector,
insert thin screwdriver wrapped in tape into notch, lift
lock and remove connector.
●
Install connector with lock raised, and push lock into
connector.
1. Driver air bag module
2. Steering wheel
3. Special bolt (TORX bolt)
4. Side lid
PHIA0680E
PHIA0683E
PHIA0341E
SRS-40
DRIVER AIR BAG MODULE
Revision: 2006 August
2006 Murano
CAUTION:
●
Always work from the side of driver air bag module.
●
Always place driver air bag module with pad side facing
upward.
●
Do not insert any foreign objects (screwdriver, etc.) into
driver air bag module.
●
Do not disassemble driver air bag module.
●
Do not use old bolts after removal; replace with new
bolts.
●
Do not expose the driver air bag module to temperatures
exceeding 90
°
C (194
°
F).
●
Replace driver air bag module if it has been dropped or
sustained an impact.
●
Do not allow oil, grease or water to come in contact with
the front passenger air bag module.
INSTALLATION
Install in the reverse order of removal.
●
For installing the air bag module, tighten the special bolts (TORX bolts).
●
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
.
PHIA0291E
SBF814E
SPIRAL CABLE
SRS-41
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2006 August
2006 Murano
SPIRAL CABLE
PFP:25554
Removal and Installation
NHS0005Q
REMOVAL
CAUTION:
●
Before servicing SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3
minutes.
●
Do not use air tools or electric tools for servicing.
1.
Remove driver air bag module. Refer to
SRS-39, "Removal and Installation"
2.
Set the steering wheel in the neutral position.
3.
Disconnect the steering horn switch connector.
4.
Remove steering wheel. Refer to
.
5.
Remove steering column cover upper and lower. Refer to
IP-12, "(F) Steering Column Cover"
6.
Loosen the spiral cable fixing screws, then remove the spiral cable.
CAUTION:
●
Do not disassemble spiral cable.
●
Do not apply lubricant to the spiral cable.
7.
Disconnect the horn switch connector, and then spiral cable
connector.
INSTALLATION
Install in the reverse order of removal.
PHIA1258E
1. Lighting and turn signal switch
2. Steering wheel
3. Drive air bag module connector
4. Screw (Do not remove)
5. Wiper and washer switch
6. Steering column cover lower
7. Steering column assembly
8. Steering column cover upper
9. Spiral cable
SHIA0193E
SRS-42
SPIRAL CABLE
Revision: 2006 August
2006 Murano
CAUTION:
●
The spiral cable may snap due to steering operation if the
cable is installed in an improper position.
●
Also, with the steering linkage disconnected the cable may
snap by turning the steering wheel beyond the limited num-
ber of turns. The spiral cable can be turned counterclock-
wise about 2.5 turns from the right end position.
●
After the work is completed, perform self-diagnosis to make
sure no malfunction is detected. Refer to
.
PHIA0275E
FRONT PASSENGER AIR BAG MODULE
SRS-43
C
D
E
F
G
I
J
K
L
M
A
B
SRS
Revision: 2006 August
2006 Murano
FRONT PASSENGER AIR BAG MODULE
PFP:K8515
Removal and Installation
NHS0005R
REMOVAL
CAUTION:
●
Before servicing SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3
minutes.
●
Always work from the side of or under front passenger air bag module.
●
Do not use air tools or electric tools for servicing.
1.
Remove instrument passenger lower panel and glove box assembly.
Refer to
IP-13, "(J) Instrument Passenger Lower Panel Assembly"
.
2.
Remove cluster lid C. Refer to
3.
Remove side ventilator assembly (RH). Refer to
IP-13, "(H) Side Ventilator Assembly (LH/RH)"
.
4.
Remove instrument side finisher (RH). Refer to
IP-13, "(I) Instrument Side Finisher (LH/RH)"
5.
Disconnect passenger air bag connector.
6.
Remove bolt, then remove instrument passenger upper panel
assembly.
7.
Remove nuts, then remove passenger air bag module.
CAUTION:
●
Always place front passenger air bag module with the air bag deployment side facing upward.
●
Do not insert any foreign objects (screwdriver, etc.) into front passenger air bag module.
●
Do not disassemble front passenger air bag module.
●
Do not use old bolts after removal; replace with new bolts.
●
Replace front passenger air bag module if it has been
dropped or sustained an impact.
●
Do not expose the front passenger air bag module to tem-
peratures exceeding 90
°
C (194
°
F).
●
Do not allow oil, grease or water to come in contact with the
front passenger air bag module.
●
After front passenger air bag module inflates, the instru-
ment panel assembly should be replaced.
Fixing bolt:
24.5 N·m (2.5 kg-m, 18 ft-lb)
PHIA0931E
Fixing nuts:
6 N·m (0.6 kg-m, 53 in-lb)
PHIA0932E
SBF814E
SRS-44
FRONT PASSENGER AIR BAG MODULE
Revision: 2006 August
2006 Murano
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Always work from the side of or under front passenger air bag module.
●
After the work is completed, perform self-diagnosis to make sure no malfunction is detected.
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст