Nissan Murano Z50 (2006 year). Manual — part 207
TROUBLE DIAGNOSES
WT-15
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision: 2006 August
2006 Murano
Wiring Diagram — T/WARN —
NES000E2
TEWB0004E
WT-16
TROUBLE DIAGNOSES
Revision: 2006 August
2006 Murano
TEWB0005E
TROUBLE DIAGNOSES
WT-17
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision: 2006 August
2006 Murano
TEWB0006E
WT-18
TROUBLE DIAGNOSES
Revision: 2006 August
2006 Murano
BCM Input/Output Signal Reference Values
NES000F8
BCM INSPECTION TABLE (FOR LOW TIRE PRESSURE WARNING SYSTEM)
Specifications with CONSULT-II
Monitor item [Unit]
Content
Condition
Display value
VHCL SPEED SE [km/h] or
[mph]
Wheel speed
Vehicle stopped
0 km/h (0 MPH)
Vehicle running
CAUTION:
Check air pressure of tire under standard condition.
Approximately
equal to the indi-
cation on speed-
ometer (Inside of
±
10%)
AIR PRESS FL [kPa], [kg/
cm
2
] or [psi]
Condition of front LH
tire air pressure
Just after the engine is started
0 kPa (0 kg/cm
2
,
0 psi)
Start engine and drive at 40 km/h (25 MPH) or more for
several minutes.
Approximately
equal to the indi-
cation on tire
gauge value
AIR PRESS FR [kPa], [kg/
cm
2
] or [psi]
Condition of front RH
tire air pressure
Just after the engine is started
0 kPa (0 kg/cm
2
,
0 psi)
Start engine and drive at 40 km/h (25 MPH) or more for
several minutes.
Approximately
equal to the indi-
cation on tire
gauge value
AIR PRESS RR [kPa], [kg/
cm
2
] or [psi]
Condition of rear LH
tire air pressure
Just after the engine is started
0 kPa (0 kg/cm
2
,
0 psi)
Start engine and drive at 40 km/h (25 MPH) or more for
several minutes.
Approximately
equal to the indi-
cation on tire
gauge value
AIR PRESS RL [kPa], [kg/
cm
2
] or [psi]
Condition of rear RH
tire air pressure
Just after the engine is started
0 kPa (0 kg/cm
2
,
0 psi)
Start engine and drive at 40 km/h (25 MPH) or more for
several minutes.
Approximately
equal to the indi-
cation on tire
gauge value
ID REGST FL [DONE/YET]
Condition of front LH
ID registration
Transmitter ID registered
DONE
Transmitter ID unregistered
YET
ID REGST FR [DONE /YET]
Condition of front RH
ID registration
Transmitter ID registered
DONE
Transmitter ID unregistered
YET
ID REGST RR [DONE/YET]
Condition of rear LH ID
registration
Transmitter ID registered
DONE
Transmitter ID unregistered
YET
ID REGST RL [DONE/YET]
Condition of rear RH ID
registration
Transmitter ID registered
DONE
Transmitter ID unregistered
YET
WARNING LAMP [ON/OFF]
Low tire pressure
warning lamp condition
Low tire pressure warning lamp: ON
ON
Low tire pressure warning lamp: OFF
OFF
BUZZER [ON/OFF]
Condition of sound
Sound heard
ON
Sound not heard
OFF
TROUBLE DIAGNOSES
WT-19
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision: 2006 August
2006 Murano
Specifications Between BCM Terminals
BCM TERMINAL CONNECTOR LAYOUT
Data are reference value and are measured between each terminal and ground.
SEIA0771E
Terminal
Wire
color
Item
Condition
Data (Approx.)
15
W
Tire pressure warning check
switch
Ignition switch: ON
5 V
Ignition switch: OFF
0 V
18
P
Remote keyless entry receiver
(Ground)
Always
0 V
19
Y
Remote keyless entry receiver
(Power supply)
Stand-by
Press any of the keyfob switches
20
L
Remote keyless entry receiver
(Signal)
Ignition switch: ON
Stand-by
Press any of the
keyfob switches
38
R
Power supply (IG)
Ignition switch: ON
Battery voltage
Ignition switch: OFF
0 V
39
L
CAN-H
—
—
40
Y
CAN-L
—
—
42
GR
Power supply (Fuse)
Ignition switch: ON
Battery voltage
Ignition switch: OFF
OCC3879D
OCC3882D
OCC3881D
OCC3880D
WT-20
TROUBLE DIAGNOSES
Revision: 2006 August
2006 Murano
CAUTION:
When using circuit tester or oscilloscope to measure voltage for inspection, be sure not to extend forcibly any connector ter-
minals.
CONSULT-II Function (AIR PRESSURE MONITOR)
NES000E7
CONSULT-II MAIN FUNCTION
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II SETTING PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
NOTE:
For details, refer to the separate “CONSULT-II Operations Manual”.
1.
Turn ignition switch “OFF”.
2.
Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector on vehicle.
3.
Turn ignition switch “ON”.
45
G/B
Turn signal lamp switch (LH)
Ignition switch: ON
Turn signal
switch to left
Battery voltage
Other than the
above
0 V
46
G/Y
Turn signal lamp switch (RH)
Ignition switch: ON
Turn signal
switch to right
Battery voltage
Other than the
above
0 V
52
B
Ground
Always
0 V
55
W/B
Power supply (F/L)
Ignition switch: ON
Battery voltage
Ignition switch: OFF
Terminal
Wire
color
Item
Condition
Data (Approx.)
Diagnostic test mode
Function
Reference
page
Work support
●
This mode enables a technician to adjust some devices faster and more accu-
rately by following the indications on CONSULT-II.
Self-diagnostic results
●
Self-diagnostic results can be read and erased quickly.
Data monitor
●
Input/Output data in the BCM can be read.
Active test
●
Diagnostic Test Mode in with CONSULT-II drives some actuators apart from the
BCM and also shifts some parameters in a specified range.
PBIB1300E
TROUBLE DIAGNOSES
WT-21
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision: 2006 August
2006 Murano
4.
Touch “START (NISSAN BASED VHCL)”.
5.
Touch “BCM”.
If “BCM” is not indicated, go to
.
6.
Touch “AIR PRESSURE MONITOR”.
7.
Perform each diagnostic test mode according to each service
procedure.
WORK SUPPORT MODE
Operation Procedure
1.
Perform “CONSULT-II SETTING PROCEDURE”. Refer to
WT-20, "CONSULT-II SETTING PROCE-
.
2.
Touch “WORK SUPPORT”.
3.
Select from “SELECT WORK ITEM”, screen of work support
mode is displayed
ID Read
The registered ID number is displayed.
ID Regist
Refer to
WT-26, "ID Registration Procedure"
SELF-DIAG RESULT MODE
Operation Procedure
1.
Perform “CONSULT-II SETTING PROCEDURE”. Refer to
WT-20, "CONSULT-II SETTING PROCE-
.
2.
Touch “SELF-DIAG RESULTS”.
Display shows malfunction experienced since the last erasing operation.
BCIA0029E
SEIA0583E
SEIA0584E
WT-22
TROUBLE DIAGNOSES
Revision: 2006 August
2006 Murano
Display item list
Items
(CONSULT-II screen terms)
Diagnostic item is detected when...
Check item
FLAT TIRE FL
[C1704]
Front LH tire pressure drops to 186 kPa (1.86 kg/cm
2
, 27 psi) or less
FLAT TIRE FR
[C1705]
Front RH tire pressure drops to 186 kPa (1.86 kg/cm
2
, 27 psi) or less
FLAT TIRE RR
[C1706]
Rear RH tire pressure drops to 186 kPa (1.86 kg/cm
2
, 27 psi) or less
FLAT TIRE RL
[C1707]
Rear LH tire pressure drops to 186 kPa (1.86 kg/cm
2
, 27 psi) or less
[NO DATA] FL
[C1708]
Data from front LH transmitter cannot be received.
[NO DATA] FR
[C1709]
Data from front RH transmitter cannot be received.
[NO DATA] RR
[C1710]
Data from rear RH transmitter cannot be received.
[NO DATA] RL
[C1711]
Data from rear LH transmitter cannot be received.
[CHECKSUM ERR] FL
[C1712]
Checksum data from front LH transmitter is malfunctioning.
[CHECKSUM ERR] FR
[C1713]
Checksum data from front RH transmitter is malfunctioning.
[CHECKSUM ERR] RR
[C1714]
Checksum data from rear RH transmitter is malfunctioning.
[CHECKSUM ERR] RL
[C1715]
Checksum data from rear LH transmitter is malfunctioning.
[PRESSDATA ERR] FL
[C1716]
Air pressure data from front LH transmitter is malfunction.
[PRESSDATA ERR] FR
[C1717]
Air pressure data from front RH transmitter is malfunction.
[PRESSDATA ERR] RR
[C1718]
Air pressure data from rear RH transmitter is malfunction.
[PRESSDATA ERR] RL
[C1719]
Air pressure data from rear LH transmitter is malfunction.
[CODE ERR] FL
[C1720]
Function code data from front LH transmitter is malfunctioning.
[CODE ERR] FR
[C1721]
Function code data from front RH transmitter is malfunctioning.
[CODE ERR] RR
[C1722]
Function code data from rear RH transmitter is malfunctioning.
[CODE ERR] RL
[C1723]
Function code data from rear LH transmitter is malfunctioning.
[BATT VOLT LOW] FL
[C1724]
Battery voltage of front LH transmitter drops.
[BATT VOLT LOW] FR
[C1725]
Battery voltage of front RH transmitter drops.
[BATT VOLT LOW] RR
[C1726]
Battery voltage of rear RH transmitter drops.
[BATT VOLT LOW] RL
[C1727]
Battery voltage of rear LH transmitter drops.
VHCL SPEED SIG ERR
[C1729]
Vehicle speed signal is error.
TROUBLE DIAGNOSES
WT-23
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision: 2006 August
2006 Murano
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or else the actual malfunction location may be different from that dis-
played on CONSULT-II.
How to Erase Self-diagnostic Results
1.
Perform applicable inspection of malfunctioning item and then repair or replace.
2.
Turn ignition switch “ON” and select “SELF-DIAG RESULTS” mode for “AIR PRESSURE MONITOR” with
CONSULT-II.
3.
Touch “ERASE” on CONSULT-II screen to erase DTC memory.
CAUTION:
If memory cannot be erased, perform applicable diagnosis.
DATA MONITOR MODE
Operation Procedure
1.
Perform “CONSULT-II SETTING PROCEDURE”. Refer to
WT-20, "CONSULT-II SETTING PROCE-
.
2.
Touch “DATA MONITOR”.
3.
Select from “SELECT MONITOR ITEM”, screen of data monitor mode is displayed.
NOTE:
When malfunction is detected, CONSULT-II performs REAL-TIME DIAGNOSIS.
Also, any malfunction detected while in this mode will be displayed at real time.
Display item List
×
: Standard
–: Not applicable
Monitored item (Unit)
Monitor item selection
Remarks
MAIN
SIGNALS
SELECTION
FROM MENU
VHCL SPEED SE [km/h] or [mph]
×
×
Vehicle speed is displayed.
AIR PRESS FL [kpa] or [psi]
×
×
Senses the front LH tire pressure is displayed.
AIR PRESS FR [kPa] or [psi]
×
×
Senses the front RH tire pressure is displayed.
AIR PRESS RR [kpa] or [psi]
×
×
Senses the rear RH tire pressure is displayed.
AIR PRESS RL [kpa] or [psi]
×
×
Senses the rear LH tire pressure is displayed.
ID REGST FL 1 [DONE/YET]
×
×
Registration status of front LH ID is displayed.
ID REGST FR 1 [DONE/YET]
×
×
Registration status of front RH ID is displayed.
ID REGST RR 1 [DONE/YET]
×
×
Registration status of rear RH ID is displayed.
ID REGST RL 1 [DONE/YET]
×
×
Registration status of rear LH ID is displayed.
WARNING LAMP [ON/OFF]
×
×
Control status of low pressure warning lamp is displayed.
BUZZER [ON/OFF]
×
×
Control status of buzzer in combination meter is dis-
played.
Voltage [V]
–
×
The value measured by the voltage probe is displayed.
Frequency [Hz]
–
×
The value measured by the pulse probe is displayed.
DUTY-HI (high) [%]
–
×
DUTY-LOW (low) [%]
–
×
PLS WIDTH-HI [msec]
–
×
PLS WIDTH-LOW [msec]
–
×
WT-24
TROUBLE DIAGNOSES
Revision: 2006 August
2006 Murano
ACTIVE TEST MODE
Operation Procedure
1.
Perform CONSULT-II SETTING PROCEDURE. Refer to
"CONSULT-II SETTING PROCEDURE"
2.
Touch “ACTIVE TEST”.
3.
Select from “SELECT TEST ITEM”, screen of active test mode
is displayed.
Test Item
Self-Diagnostic Procedure
NES000E8
SELF-DIAGNOSTIC PROCEDURE (WITH CONSULT-II)
Refer to
WT-21, "SELF-DIAG RESULT MODE"
SELF-DIAGNOSTIC PROCEDURE (WITHOUT CONSULT-II)
Description
The low tire pressure warning lamp in the combination meter will flicker according to the self-diagnostic
results. As for the details of the low tire pressure warning lamp flickering patterns, refer to
SEIA0585E
Test item
Content
FLASHER
This test is able to check to make sure that each turn signal lamp turns on.
HORN
This test is able to check to make sure that the horn sounds.
WARNING LAMP
This test is able to check to make sure that the warning lamp turns on.
ID REGIST WARNING
This test is able to check to make sure that the buzzer sounds or the warning lamp turns on.
FLAT TIRE WARNING
This test is able to check to make sure that the buzzer sounds or the warning lamp turns on.
TROUBLE DIAGNOSES
WT-25
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision: 2006 August
2006 Murano
Diagnostic Procedure
1.
Start the engine.
2.
Perform the following procedures to enter the corresponding signals.
a.
Ground the tire pressure warning check switch harness connector terminal 1 for more than 5 seconds.
b.
Read the flickering of low tire pressure warning lamp. Refer to
WT-25, "Judgement Self-diagnosis"
.
NOTE:
When the low tire pressure warning lamp flashes 5 Hz and continues repeating it, the system is normal.
Judgement Self-diagnosis
When a malfunction is detected, the malfunction route is indicated by flickering of the low tire pressure warn-
ing lamp.
NOTE:
When the low tire pressure warning lamp flashes 5 Hz and continues repeating it, the system is normal.
Flickering pattern
Items
Diagnostic item is detected when...
Check item
15
Tire pressure value
(front LH)
Front LH tire pressure drops to 186 kPa (1.86 kg/cm
2
, 27 psi)
or less
16
Tire pressure value
(front RH)
Front RH tire pressure drops to 186 kPa (1.86 kg/cm
2
, 27 psi)
or less
17
Tire pressure value
(rear RH)
Rear RH tire pressure drops to 186 kPa (1.86 kg/cm
2
, 27 psi)
or less
18
Tire pressure value
(rear LH)
Rear LH tire pressure drops to 186 kPa (1.86 kg/cm
2
, 27 psi)
or less
21
Transmitter no data
(front LH)
Data from front LH transmitter cannot be received.
22
Transmitter no data
(front RH)
Data from front RH transmitter cannot be received.
23
Transmitter no data
(rear RH)
Data from rear RH transmitter cannot be received.
24
Transmitter no data
(rear LH)
Data from rear LH transmitter cannot be received.
31
Transmitter checksum
error (front LH)
Checksum data from front LH transmitter is malfunctioning.
32
Transmitter checksum
error (front RH)
Checksum data from front RH transmitter is malfunctioning.
33
Transmitter checksum
error (rear RH)
Checksum data from rear RH transmitter is malfunctioning.
34
Transmitter checksum
error (rear LH)
Checksum data from rear LH transmitter is malfunctioning.
SEIA0745E
WT-26
TROUBLE DIAGNOSES
Revision: 2006 August
2006 Murano
ERASE SELF-DIAGNOSIS
●
In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is
stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned “ON” and “OFF”.
●
However, this information is erased by turning ignition switch “OFF” after performing self-diagnostics or by
erasing the memory using the CONSULT-II. Refer to
WT-23, "How to Erase Self-diagnostic Results"
.
ID Registration Procedure
NES000FG
ID REGISTRATION WITH TRANSMITTER ACTIVATION TOOL
CAUTION:
This procedure must be done after replacement of a transmitter, BCM, or rotating wheels.
1.
Perform “CONSULT-II SETTING PROCEDURE”. Refer to
WT-20, "CONSULT-II SETTING PROCE-
2.
Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen, and select “ID REGIST”.
3.
With the transmitter activation tool (J-45295) pushed against the
front-left transmitter position of the air valve, press and hold the
button for 5 seconds.
4.
Register the IDs in order from FR LH, FR RH, RR RH, to RR LH.
When ID registration of each wheel has been completed, buzzer
sounds and turn signal lamp blinks.
35
Transmitter pressure
data error (front LH)
Air pressure data from front LH transmitter is malfunction.
36
Transmitter pressure
data error (front RH)
Air pressure data from front RH transmitter is malfunction.
37
Transmitter pressure
data error (rear RH)
Air pressure data from rear RH transmitter is malfunction.
38
Transmitter pressure
data error (rear LH)
Air pressure data from rear LH transmitter is malfunction.
41
Transmitter function
code error (front LH)
Function code data from front LH transmitter is malfunction-
ing.
42
Transmitter function
code error (front RH)
Function code data from front RH transmitter is malfunction-
ing.
43
Transmitter function
code error (rear RH)
Function code data from rear RH transmitter is malfunction-
ing.
44
Transmitter function
code error (rear LH)
Function code data from rear LH transmitter is malfunctioning.
45
Transmitter battery volt-
age low (front LH)
Battery voltage of front LH transmitter drops.
46
Transmitter battery volt-
age low (front RH)
Battery voltage of front RH transmitter drops.
47
Transmitter battery volt-
age low (rear RH)
Battery voltage of rear RH transmitter drops.
48
Transmitter battery volt-
age low (rear LH)
Battery voltage of rear LH transmitter drops.
52
Vehicle speed signal
error
Speed signal is not detected.
No flickering
Tire pressure warning
check switch
Tire pressure warning check switch circuit is open.
—
Flickering pattern
Items
Diagnostic item is detected when...
Check item
SEIA0460E
TROUBLE DIAGNOSES
WT-27
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision: 2006 August
2006 Murano
5.
After completing all ID registrations, press “END” to complete the procedure.
NOTE:
Be sure to register the IDs in order from FR LH, FR RH, RR RH, to RR LH, or the self-diagnostic results dis-
play will not function properly.
ID REGISTRATION WITHOUT TRANSMITTER ACTIVATION TOOL
CAUTION:
This procedure must be done after replacement of a transmitter, BCM, or rotating wheels.
1.
Perform “CONSULT-II SETTING PROCEDURE”. Refer to
WT-20, "CONSULT-II SETTING PROCE-
.
2.
Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen, and select “ID REGIST”.
3.
Adjust the tire pressure to the values shown in the table below for ID registration, and drive the vehicle at
40 km/h (25 MPH) or more for several minutes.
NOTE:
If ID registration is unable, buzzer beeps.
4.
After completing all ID registrations, press “END” to complete the procedure.
5.
Inflate all tires to proper pressure. Refer to
.
Activation tire position
Buzzer
Turn signal lamp
CONSULT-II
1
Front LH
Once
2 times flashing
“YET”
↓
“DONE”
2
Front RH
2 times
3
Rear RH
3 times
4
Rear LH
4 times
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
240 (2.4, 34)
Front RH
220 (2.2, 31)
Rear RH
200 (2.0, 29)
Rear RH
180 (1.8, 26)
Activation tire position
CONSULT-II
Front LH
“YET”
↓
“DONE”
Front RH
Rear RH
Rear LH
WT-28
TROUBLE DIAGNOSES
Revision: 2006 August
2006 Murano
Transmitter Wake Up Operation
NES000FH
WITH ACTIVATION TOOL
1.
With the transmitter activation tool (J-45295) pushed against the
front-left transmitter, press and hold the button for 5 seconds.
●
When ignition switch ON, and then low tire pressure warning
lamp blinks as per the following diagram, the respective then
transmitter must be wake up.
2.
Register the ID of wheel that warning lamp flashes. When wake up of registered wheel has been com-
pleted, turn signal lamp flashes two times.
3.
After completing wake up all transmitters, make sure low tire pressure warning lamp goes out.
Trouble Diagnosis Chart for Symptoms
NES000E3
If low tire pressure warning lamp turns ON, perform self-diagnosis. Refer to
WT-24, "Self-Diagnostic Procedure"
SEIA0460E
SEIA0762E
Symptom
Condition
Check item
Reference page
Low tire pressure warning lamp does not
turn ON for approx.1 second when ignition
switch is turned ON.
Ignition ON
CAN communication line
Combination meter
BCM
Low tire pressure warning lamp stays ON
when ignition switch is turned ON.
Engine running
ID registration
Power supply and ground for BCM
BCM
Low tire pressure warning lamp blinks when
ignition switch is turned ON.
Ignition ON
BCM connector or circuit
BCM
Turn signal lamp blinks when ignition switch
is turned ON.
Ignition ON
BCM connector or circuit
BCM
ID registration cannot be completed.
Engine running
Transmitter
Remote keyless entry receiver connec-
tor or circuit
Remote keyless entry receiver
BCM connector or circuit
BCM
TROUBLE DIAGNOSES
WT-29
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision: 2006 August
2006 Murano
Low Tire Pressure Warning Lamp Symptom Chart
NES000F7
Diagnosis
Item
Symptom
(Ignition switch ON)
Low tire pressure warning lamp
Cause
Action
Low tire pres-
sure warning
lamp
Warning light comes
on immediately and
turns off after 1 sec-
ond.
All wheel transmit-
ters are “activated”
(working).
None (system OK)
Warning light blinks
on for 2 seconds,
then turns off for 0.2
seconds-repeats.
All wheel transmit-
ters are not acti-
vated.
Activate all wheel transmit-
ters. Refer to
"Transmitter Wake Up Oper-
ation"
Warning light blinks 1
time.
Front LH wheel
transmitter is not
activated.
Activate front LH wheel
transmitter. Refer to
"Transmitter Wake Up Oper-
ation"
Warning light blinks 2
times.
Front RH wheel
transmitter is not
activated.
Activate front RH wheel
transmitter. Refer to
"Transmitter Wake Up Oper-
ation"
Warning light blinks 3
times.
Rear RH wheel
transmitter is not
activated.
Activate rear RH wheel
transmitter. Refer to
"Transmitter Wake Up Oper-
ation"
SEIA0592E
SEIA0593E
PEIA0073E
SEIA0595E
SEIA0596E
WT-30
TROUBLE DIAGNOSES
Revision: 2006 August
2006 Murano
NOTE:
If more than one wheel transmitter is NOT activated, the warning light blinking patterns for those wheels will combine. (Example: one
blink/“OFF”/three blinks = Rear LH and Rear RH transmitters are not activated.)
Low tire pres-
sure warning
lamp
Warning light blinks 4
times.
Rear LH wheel trans-
mitter is not acti-
vated.
Activate rear LH wheel
transmitter. Refer to
"Transmitter Wake Up Oper-
ation"
Warning light comes
on and does not turn
off.
Tire pressure is low.
Check tire pressure with
CONSULT-II. Refer to
The fuse for combi-
nation meter from
battery is pulled out.
Check the fuse for combina-
tion meter from battery.
Install or replace (if needed).
BCM connector
pulled out.
Check BCM connector. Re-
connect if needed.
Low tire pressure or
low tire pressure
warning system mal-
function.
●
Perform CONSULT-II
Self- Diagnosis. Refer to
WT-21, "SELF-DIAG
RESULT MODE"
.
–
Perform ID Registration if
needed. Refer to
Turn signal
lamp
Turn signal lamp
does not flash 2
times or buzzer does
not sound after trans-
mitter activation.
1. Tool J-45295 (spe-
cial service tool) bat-
tery low.
1. Install new battery.
2. Ignition OFF dur-
ing activation.
2. Make sure ignition is ON
during activation.
3. Tool J-45295 (spe-
cial service tool) not
positioned correctly.
3. Position tool correctly dur-
ing activation.
4. Transmitters
already activated.
4. None
Diagnosis
Item
Symptom
(Ignition switch ON)
Low tire pressure warning lamp
Cause
Action
SEIA0597E
SEIA0598E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст