Nissan GT-R (2007-2014 year). POWER CONTROL SYSTEM / POWER WINDOW CONTROL SYSTEM. Service Manual — part 4
PWC-18
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW SUB-SWITCH
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace power window main switch. Refer to
PWC-46, "Removal and Installation"
5.
CHECK POWER WINDOW SUB-SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector and power window sub-switch connector.
3.
Check continuity between power window main switch harness connector and power window sub-switch
harness connector.
4.
Check continuity between power window sub-switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000009159925
1.
CHECK POWER WINDOW SUB-SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect power window sub-switch connector.
3.
Check continuity between power window sub-switch terminals.
(+)
(
−
)
Voltage (V)
(Approx.)
Power window main switch
Connector
Terminal
D8
16
Ground
Battery voltage
Power window sub-switch
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
D38
3
D8
16
Existed
Power window sub-switch
Ground
Continuity
Connector
Terminal
D38
3
Not existed
2014 GT-R
POWER WINDOW SUB-SWITCH
PWC-19
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace power window sub-switch. Refer to
PWC-46, "Removal and Installation"
Power window sub-switch
Condition
Continuity
Connector
Terminal
D38
14
3
AUTO
Existed
5
Not existed
3
Other than above
Not existed
5
Existed
15
3
UP
Existed
6
Not existed
3
Other than above
Not existed
6
Existed
16
3
DOWN
Existed
7
Not existed
3
Other than above
Not existed
7
Existed
2014 GT-R
PWC-20
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW MOTOR
POWER WINDOW MOTOR
Description
INFOID:0000000009159926
• Operates via UP or DOWN signal from power window main switch or power window sub-switch.
• Encoder and module are built-in and controls anti-pitch function, AUTO operation, and automatic window
adjusting function.
Component Function Check
INFOID:0000000009159927
1.
CHECK FUNCTION
Check that corresponding power window operates when power window switch (power window lock switch is
UNLOCK) is operated to the UP or DOWN position.
Is the inspection result normal?
YES
>> Power window motor function is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009159928
1.
CHECK POWER WINDOW MOTOR INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Power window lock switch OFF.
3.
Check voltage between malfunctioning power window motor harness connector and ground.
*: Passenger side
Is the inspection result normal?
YES
>> Replace malfunctioning power window motor. Refer to
GW-27, "Removal and Installation (GT-R
NO
>> GO TO 2.
2.
CHECK POWER WINDOW MOTOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the corresponding power window motor connector and power window switch connector.
3.
Check continuity between the corresponding power window motor harness connector and power window
switch harness connector.
*: Passenger side
4.
Check continuity between the corresponding power window motor harness connector and ground.
(+)
(
−
)
Condition
Voltage (V)
(Approx.)
Power window motor
Connector
Terminal
D10/D40*
3
Ground
When operating the corresponding power window switch upwards
Battery voltage
Other than above
0
4
When operating the corresponding power window switch downwards
Battery voltage
Other than above
0
Power window motor
Power window switch
Continuity
Connector
Terminal
Connector
Terminal
D10/D40*
3
D8/D38*
10/15*
Existed
4
11/16*
Power window motor
Ground
Continuity
Connector
Terminal
D10/D40*
3
Not existed
4
2014 GT-R
POWER WINDOW MOTOR
PWC-21
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
*: Passenger side
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between the corresponding power window motor harness connector and ground.
*: Passenger side
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
.
>> INSPECTION END
Power window motor
Ground
Continuity
Connector
Terminal
D10/D40*
8
Existed
2014 GT-R
PWC-22
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW AUTO CIRCUIT
POWER WINDOW AUTO CIRCUIT
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Description
INFOID:0000000009159929
Sends AUTO signal to driver side or passenger side power window motor.
POWER WINDOW MAIN SWITCH : Component Function Check
INFOID:0000000009159930
1.
CHECK FUNCTION
Check that corresponding power window operates when driver side or passenger side switch of power window
main switch (power window lock is UNLOCK) is operated to the AUTO position.
Is the inspection result normal?
YES
>> Power window main switch AUTO function is OK.
NO
>> Refer to
PWC-22, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
POWER WINDOW MAIN SWITCH : Diagnosis Procedure
INFOID:0000000009159931
1.
CHECK POWER WINDOW AUTO FUNCTION
1.
Turn ignition switch ON.
2.
Power window lock switch UNLOCK.
3.
Operate driver side and passenger side switch of power window main switch to the AUTO position.
Which side of power window AUTO operation does not operate?
Driver side>>GO TO 2.
Passenger side>>GO TO 5.
2.
CHECK DRIVER SIDE POWER WINDOW MOTOR INPUT SIGNAL
Check voltage between driver side power window motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace driver side power window motor. Refer to
GW-27, "Removal and Installation (GT-R certi-
.
NO
>> GO TO 3.
3.
CHECK POWER WINDOW AUTO SIGNAL CIRCUIT 1
1.
Turn ignition switch OFF.
2.
Disconnect driver side power window motor connector and power window main switch connector.
3.
Check continuity between driver side power window motor harness connector and power window main
switch harness connector.
4.
Check continuity between driver side power window motor harness connector and ground.
(+)
(–)
Condition
Voltage (V)
(Approx.)
Driver side power window motor
Connector
Terminal
D10
1
Ground
Power window
main switch
(driver side switch)
AUTO
Battery voltage
Other than above
0
3
UP
Battery voltage
Other than above
0
4
DOWN
Battery voltage
Other than above
0
Driver side power window motor
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
D10
1
D8
3
Existed
2014 GT-R
POWER WINDOW AUTO CIRCUIT
PWC-23
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK POWER WINDOW MAIN SWITCH (DRIVER SIDE)
Check power window main switch (driver side).
Refer to
PWC-13, "DRIVER SIDE : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Replace power window main switch. Refer to
PWC-46, "Removal and Installation"
5.
CHECK PASSENGER SIDE POWER WINDOW MOTOR INPUT SIGNAL
Check voltage between passenger side power window motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace passenger side power window motor. Refer to
GW-27, "Removal and Installation (GT-R
NO
>> GO TO 6.
6.
CHECK POWER WINDOW SUB-SWITCH OUTPUT SIGNAL
Check voltage between power window sub-switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 8.
7.
CHECK POWER WINDOW AUTO SIGNAL CIRCUIT 2
1.
Turn ignition switch OFF.
2.
Disconnect passenger side power window motor connector and power window sub-switch connector.
Driver side power window motor
Ground
Continuity
Connector
Terminal
D10
1
Not existed
(+)
(–)
Condition
Voltage (V)
(Approx.)
Passenger side power window motor
Connector
Terminal
D40
1
Ground
Power window main
switch
(passenger side
switch)
AUTO
Battery voltage
Other than above
0
3
UP
Battery voltage
Other than above
0
4
DOWN
Battery voltage
Other than above
0
(+)
(–)
Condition
Voltage (V)
(Approx.)
Power window sub-switch
Connector
Terminal
D38
14
Ground
Power window
main switch
(passenger side
switch)
AUTO
Battery voltage
Other than above
0
15
UP
Battery voltage
Other than above
0
16
DOWN
Battery voltage
Other than above
0
2014 GT-R
PWC-24
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW AUTO CIRCUIT
3.
Check continuity between passenger side power window motor harness connector and power window
sub-switch harness connector.
4.
Check continuity between passenger side power window motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Repair or replace harness.
8.
CHECK POWER WINDOW SUB-SWITCH INPUT SIGNAL
Check voltage between power window sub-switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 10.
9.
CHECK POWER WINDOW SUB-SWITCH
Check power window sub-switch.
Refer to
PWC-18, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Replace power window sub-switch. Refer to
PWC-46, "Removal and Installation"
.
10.
CHECK POWER WINDOW MAIN SWITCH OUTPUT SIGNAL
Check voltage between power window main switch harness connector and ground.
Is the inspection result normal?
Passenger side power window motor
Power window sub-switch
Continuity
Connector
Terminal
Connector
Terminal
D40
1
D38
14
Existed
Passenger side power window motor
Ground
Continuity
Connector
Terminal
D40
1
Not existed
(+)
(–)
Condition
Voltage (V)
(Approx.)
Power window sub-switch
Connector
Terminal
D38
5
Ground
Power window
main switch
(passenger side
switch)
AUTO
Battery voltage
Other than above
0
6
UP
Battery voltage
Other than above
0
7
DOWN
Battery voltage
Other than above
0
(+)
(–)
Condition
Voltage (V)
(Approx.)
Power window main switch
Connector
Terminal
D8
6
Ground
Power window
main switch
(passenger side
switch)
AUTO
Battery voltage
Other than above
0
7
UP
Battery voltage
Other than above
0
15
DOWN
Battery voltage
Other than above
0
2014 GT-R
POWER WINDOW AUTO CIRCUIT
PWC-25
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
YES
>> GO TO 11.
NO
>> GO TO 12.
11.
CHECK POWER WINDOW AUTO SIGNAL CIRCUIT 3
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector and power window sub-switch connector.
3.
Check continuity between power window main switch harness connector and power window sub-switch
harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Repair or replace harness.
12.
CHECK POWER WINDOW MAIN SWITCH (PASSENGER SIDE)
PWC-16, "PASSENGER SIDE : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Replace power window main switch. Refer to
PWC-46, "Removal and Installation"
13.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
.
>> INSPECTION END
POWER WINDOW SUB-SWITCH
POWER WINDOW SUB-SWITCH : Description
INFOID:0000000009159932
Sends AUTO signal to passenger side power window motor.
POWER WINDOW SUB-SWITCH : Component Function Check
INFOID:0000000009159933
1.
CHECK FUNCTION
Check that passenger side power window operates when power window sub-switch (power window lock
switch is UNLOCK) is operated to the AUTO position.
Is the inspection result normal?
YES
>> Power window sub-switch AUTO function is OK.
NO
>> Refer to
PWC-25, "POWER WINDOW SUB-SWITCH : Diagnosis Procedure"
POWER WINDOW SUB-SWITCH : Diagnosis Procedure
INFOID:0000000009159934
1.
CHECK PASSENGER SIDE POWER WINDOW MOTOR INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Power window lock switch UNLOCK.
3.
Check voltage between passenger side power window motor harness connector and ground.
Power window main switch
Power window sub-switch
Continuity
Connector
Terminal
Connector
Terminal
D8
6
D38
5
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D8
6
Not existed
2014 GT-R
PWC-26
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW AUTO CIRCUIT
Is the inspection result normal?
YES
>> Replace passenger side power window motor. Refer to
GW-27, "Removal and Installation (GT-R
NO
>> GO TO 2.
2.
CHECK POWER WINDOW AUTO SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect passenger side power window motor connector and power window sub-switch connector.
3.
Check continuity between passenger side power window motor harness connector and power window
sub-switch harness connector.
4.
Check continuity between passenger side power window motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK POWER WINDOW SUB-SWITCH
Check power window sub-switch.
Refer to
PWC-18, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace power window sub-switch. Refer to
PWC-46, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
>> INSPECTION END
(+)
(
−
)
Condition
Voltage (V)
(Approx.)
Passenger side power window motor
Connector
Terminal
D40
1
Ground
Power window sub-
switch
AUTO
Battery voltage
Other than above
0
Passenger side power window motor
Power window sub-switch
Continuity
Connector
Terminal
Connector
Terminal
D40
1
D38
14
Existed
Passenger side power window motor
Ground
Continuity
Connector
Terminal
D40
1
Not existed
2014 GT-R
POWER WINDOW SWITCH ILLUMINATION CIRCUIT
PWC-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW SWITCH ILLUMINATION CIRCUIT
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Description
INFOID:0000000009159935
When ignition switch turns ON, power window main switch illuminates.
POWER WINDOW MAIN SWITCH : Component Function Check
INFOID:0000000009159936
1.
CHECK FUNCTION
Check that power window main switch illuminates when ignition switch turns ON.
Is the inspection result normal?
YES
>> Power window main switch illumination circuit is OK.
NO
>> Refer to
PWC-27, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
POWER WINDOW MAIN SWITCH : Diagnosis Procedure
INFOID:0000000009159937
1.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-46, "Removal and Installation"
NO
>> Repair or replace harness.
POWER WINDOW SUB-SWITCH
POWER WINDOW SUB-SWITCH : Description
INFOID:0000000009159938
When ignition switch turns ON, power window sub-switch illuminates.
POWER WINDOW SUB-SWITCH : Component Function Check
INFOID:0000000009159939
1.
CHECK FUNCTION
Check that power window sub-switch illuminates when ignition switch turns ON.
Is the inspection result normal?
YES
>> Power window sub-switch illumination circuit is OK.
NO
>> Refer to
PWC-27, "POWER WINDOW SUB-SWITCH : Diagnosis Procedure"
POWER WINDOW SUB-SWITCH : Diagnosis Procedure
INFOID:0000000009159940
1.
CHECK POWER WINDOW SUB-SWITCH INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between power window sub-switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
Power window main switch
Ground
Continuity
Connector
Terminal
D8
8
Existed
(+)
(
−
)
Voltage (V)
(Approx.)
Power window sub-switch
Connector
Terminal
D38
11
Ground
Battery voltage
2014 GT-R
PWC-28
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW SWITCH ILLUMINATION CIRCUIT
NO
>> GO TO 2.
2.
CHECK POWER WINDOW SUB-SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window sub-switch connector and passenger side power window motor connector.
3.
Check continuity between power window sub-switch harness connector and passenger side power win-
dow motor harness connector.
4.
Check continuity between power window sub-switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window sub-switch connector.
3.
Check continuity between power window sub-switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window sub-switch. Refer to
PWC-46, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
>> INSPECTION END
Power window sub-switch
Passenger side power window motor
Continuity
Connector
Terminal
Connector
Terminal
D38
11
D40
2
Existed
Power window sub-switch
Ground
Continuity
Connector
Terminal
D38
11
Not existed
Power window sub-switch
Ground
Continuity
Connector
Terminal
D38
8
Existed
2014 GT-R
DOOR SWITCH CIRCUIT
PWC-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
DOOR SWITCH CIRCUIT
Description
INFOID:0000000009159941
Detects driver side and passenger side doors open or closed condition.
Component Function Check
INFOID:0000000009159942
1.
CHECK FUNCTION
Check that driver side and passenger side automatic window adjustment function operates.
Is the inspection result normal?
YES
>> Door switch circuit function is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009159943
1.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-44, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Check voltage signal between power window motor harness connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> Replace malfunctioning power window motor. Refer to
GW-27, "Removal and Installation (GT-R
NO
>> GO TO 3.
3.
CHECK DOOR SWITCH CIRCUIT
1.
Disconnect BCM connector and malfunctioning power window motor connector.
2.
Check continuity between BCM harness connector and malfunctioning power window motor harness con-
nector.
(+)
(–)
Condition
Voltage (V)
(Approx.)
Power window motor
Connector
Terminal
D10
6
Ground
Door switch
(driver side)
Pressed
Released
0
D40
Door switch
(passenger side)
Pressed
Released
0
JPMIA0011GB
JPMIA0011GB
2014 GT-R
PWC-30
< DTC/CIRCUIT DIAGNOSIS >
DOOR SWITCH CIRCUIT
3.
Check continuity between malfunctioning power window motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
>> INSPECTION END
Power window motor
BCM
Continuity
Connector
Terminal
Connector
Terminal
Driver side
D10
6
M123
150
Existed
Passenger side
D40
124
Power window motor
Ground
Continuity
Connector
Terminal
Driver side
D10
6
Not existed
Passenger side
D40
2014 GT-R
POWER WINDOW MOTOR
PWC-31
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ECU DIAGNOSIS INFORMATION
POWER WINDOW MOTOR
Wiring Diagram - POWER WINDOW SYSTEM -
INFOID:0000000009159949
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCKWA1313GB
2014 GT-R
PWC-32
< ECU DIAGNOSIS INFORMATION >
POWER WINDOW MOTOR
Fail-Safe
INFOID:0000000009159950
FAIL-SAFE CONTROL
Fail-safe control is activated when the actual glass position that is out of the specified value is detected com-
pared to the fully closed position memorized in module in power window motor, or when a malfunction is
detected in the encoder signal that indicates UP or DOWN speed and direction of door glass.
In fail-safe control, the system changes to a non-initialized condition and the following functions do not oper-
ate.
• AUTO UP operation
• Anti-pinch function
• Timer function
• Automatic window adjusting function
When fail-safe control is activated, perform initializing operation to recover. If a malfunction is detected in
power window motor, fail-safe control is activated again.
Malfunction
Malfunction condition
Pulse direction malfunc-
tion (opposite backlash
pulse detection)
When a pulse signal indicates that the window is moving in the opposite direction against the power
window motor is detected for the specified value or more, while door glass is being operated UP or
DOWN.
Pulse sensor (Hall IC)
malfunction (one side
pulse shut-off detection)
When one pulse signal that is the specified value or more is detected continuously for the specified
time or more, while door glass is being operated UP or DOWN.
Both pulse sensor mal-
function (both sides pulse
shut-off detection)
When both pulse signals are not detected continuously for the specified time or more, while door
glass is being operated UP or DOWN.
Glass recognition position
malfunction 1 (UP over-
run)
When the actual door glass position that is out of the specified value is detected compared to the
door glass fully closed position memorized in module, while door glass is being operated UP. (Actual
door glass fully closed position is detected to be higher than the memorized position in module for
the specified value or more.)
Glass recognition position
malfunction 2 (Out of
memorized area)
When the actual door glass position that is out of the specified value is detected compared to the
door glass fully closed position memorized in module, while door glass is being operated UP. (Actual
door glass fully closed position is detected to be lower than the memorized position in module for the
specified value or more.)
Glass recognition position
malfunction 3 (Full stroke
malfunction)
When pulse count that is out of the door glass full stroke value or more is detected, while door glass
is being operated UP.
Fully closed position up-
date malfunction
When door glass is continuously operated UP and DOWN for the specified value or more without
fully closing door glass.
2014 GT-R
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY SWITCH
PWC-33
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
SYMPTOM DIAGNOSIS
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY
SWITCH
Diagnosis Procedure
INFOID:0000000009159951
1.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK POWER WINDOW MOTOR POWER SUPPLY AND GROUND CIRCUIT
Check power window motor power supply and ground circuit.
Refer to
PWC-10, "POWER WINDOW MOTOR : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY AND GROUND CIRCUIT
Check power window main switch power supply and ground circuit.
Refer to
PWC-11, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
NO
>> GO TO 1.
2014 GT-R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст