Nissan Frontier. Manual — part 1121
FRONT SEAT
SE-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Manual Driver Seat
AWJIA0467GB
1.
Headrest
2.
Seatback assembly
3.
Lumbar support lever knob
4.
Snap ring
5.
Seat cushion trim cover
6.
Seat cushion pad
7.
Seat cushion frame
8.
Seat cushion inner finisher
9.
Seat belt buckle assembly
10. Seat frame assembly
11. Leg cover
12. Bolt cover
13. Recline lever
14. Seat cushion outer finisher
15. Leg cover
SE-30
< REMOVAL AND INSTALLATION >
FRONT SEAT
Conventional Passenger Seat
16. Seat cushion rear finisher
17. Seat cushion lift knobs
18. Seatback board
19. Headrest holder with multi position
lock
20. Headrest holder
AWJIA0468GB
1.
Headrest
2.
Seatback assembly with side air bag 3.
Switch assembly
4.
Power seat switch escutcheon
5.
Recliner switch knob
6.
Slide switch knob
7.
Seat cushion assembly
8.
Seat cushion outer cover
9.
Leg cover
FRONT SEAT
SE-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Fold Flat Passenger Seat
10. Seat cushion front finisher
11. Passenger seat wiring harness
12. Power seat frame assembly
13. Seat cushion inner finisher
14. Seat belt buckle assembly
15. Leg cover
16. Seat cushion rear finisher
17. Manual seat frame assembly
18. Recline lever
19. Seat cushion rear finisher
20. Seatback board
21. Headrest holder with multi position
lock
22. Headrest holder
AWJIA0469GB
SE-32
< REMOVAL AND INSTALLATION >
FRONT SEAT
Removal and Installation
INFOID:0000000009479574
REMOVAL
CAUTION:
• Before removing the front seat, turn the ignition switch off, disconnect both battery terminals and
wait at least three minutes.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After front side air bag module inflates, front seatback assembly must be replaced.
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
• When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
1. Slide the seat until the four bolts are visible and a suitable tool can be inserted.
NOTE:
Set the front/rear cushion lifters to the top position.
2. Disconnect both battery terminals and wait at least three minutes. Refer to
3. Disconnect the harness connector from the side air bag module.
4. Remove the leg covers.
5. Remove the four front seat bolts.
6. Disconnect the harness connectors from the power seat and remove.
NOTE:
When removing and installing the seat, use shop cloths to protect the vehicle from damage.
INSTALLATION
Installation is in the reverse order of removal.
1.
Front seatback lever
2.
Headrest
3.
Seatback assembly
4.
Seat cushion assembly
5.
Seat cushion outer finisher
6.
Leg cover
7.
Seat frame assembly
8.
Passenger seat wiring harness
9.
Seat cushion inner cover
10. Inboard reclining arm outer cover
11. Seat belt buckle assembly
12. Leg cover
13. Inboard reclining arm inner cover
14. Outboard reclining arm inner cover
15. Seat cushion rear finisher
16. Outboard reclining arm outer cover
17. Seatback board
18. Headrest holder with multi position
lock
19. Headrest holder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст