Nissan Frontier. Manual — part 385
ENGINE CONTROL SYSTEM
EC-111
< WIRING DIAGRAM >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ABBIA1556GB
EC-112
< BASIC INSPECTION >
[QR25DE]
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Trouble Diagnosis Introduction
INFOID:0000000009480754
INTRODUCTION
The engine has an ECM to control major systems such as fuel con-
trol, ignition control, idle air control system, etc. The ECM accepts
input signals from sensors and instantly drives actuators. It is essen-
tial that both input and output signals are proper and stable. At the
same time, it is important that there are no malfunctions such as vac-
uum leaks, fouled spark plugs, or other malfunctions with the engine.
It is much more difficult to diagnose an incident that occurs intermit-
tently rather than continuously. Most intermittent incidents are
caused by poor electric connections or improper wiring. In this case,
careful checking of suspected circuits may help prevent the replace-
ment of good parts.
A visual check only may not find the cause of the incidents. A road
test with CONSULT (or GST) or a circuit tester connected should be
performed. Follow the WORK FLOW on "WORK FLOW".
Before undertaking actual checks, take a few minutes to talk with a
customer who approaches with a driveability complaint. The cus-
tomer can supply good information about such incidents, especially
intermittent ones. Find out what symptoms are present and under
what conditions they occur. A DIAGNOSTIC WORKSHEET like the
example on "Worksheet Sample" should be used.
Start your diagnosis by looking for conventional malfunctions first.
This will help troubleshoot driveability malfunctions on an electroni-
cally controlled engine vehicle.
WORK FLOW
Overall Sequence
MEF036D
SEF233G
SEF234G
DIAGNOSIS AND REPAIR WORK FLOW
EC-113
< BASIC INSPECTION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
*1: Include 1st trip DTC.
*2: Include 1st trip freeze frame data.
Detailed Flow
1.
GET INFORMATION FOR SYMPTOM
1. Get the detailed information from the customer about the symptom (the condition and the environment
when the incident/malfunction occurred) using the "DIAGNOSTIC WORKSHEET".
2. Ask if the customer requests I/M examination.
JSBIA0123GB
EC-114
< BASIC INSPECTION >
[QR25DE]
DIAGNOSIS AND REPAIR WORK FLOW
Malfunction information, obtained>>GO TO 2.
No malfunction information, but a request for I/M examination>>GO TO 13.
2.
CHECK DTC
1. Check DTC of “ALL DTC Reading”.
2. Perform the following procedure if DTC is displayed.
-
Record DTC and freeze frame data. (Print them out with CONSULT or GST.)
-
Erase DTC. (Refer to
.)
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
(Symptom Matrix Chart is useful. Refer to
EC-461, "Symptom Matrix Chart"
3. Check related service bulletins for information.
Are any symptoms described and any DTCs detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer (except MIL ON).
Also study the normal operation and fail safe related to symptom. Refer to
EC-465, "Fuel Cut Control (at No
Diagnosis Work Sheet is useful to verify the incident.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Also study the normal operation and fail safe related to symptom. Refer to
EC-465, "Fuel Cut Control (at No
Diagnosis Work Sheet is useful to verify the incident.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then make sure that DTC is detected again.
If two or more DTCs are detected, refer to
EC-82, "DTC Inspection Priority Chart"
nosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Overall Function Check if DTC Confirmation Procedure is not included on Service Manual. This
simplified check procedure is an effective alternative though DTC cannot be detected during this check.
If the result of Overall Function Check is NG, it is the same as the detection of DTC by DTC Confirmation
Procedure.
Is DTC detected?
YES
>> GO TO 10.
NO
>> Check according to
GI-42, "Intermittent Incident"
.
6.
PERFORM BASIC INSPECTION
Perform
With CONSULT>>GO TO 7.
Without CONSULT>>GO TO 9.
7.
PERFORM SPEC IN DATA MONITOR MODE
With CONSULT
Make sure that “MAS A/F SE-B1”, “B/FUEL SCHDL”, and “A/F ALPHA-B1” are within the SP value using
“SPEC” of “DATA MONITOR” mode using CONSULT. Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст