Nissan Frontier. Manual — part 566
P0850 PNP SWITCH
EC-835
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE FOR USA AND CANADA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2. Check harness continuity between ECM terminal 117 and combination meter terminal 7.
Refer to Wiring Diagram.
3. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E152, M31
• Harness for open or short between ECM and combination meter
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK PNP INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-III
1. Check harness continuity between A/T assembly terminal 9 and TCM terminal 8.
Refer to Wiring Diagram.
2. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 8.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
OK or NG
OK
>> GO TO 9.
NG
>> Repair or replace.
9.
REPLACE COMBINATION METER
MWI-5, "METER SYSTEM : System Diagram"
.
>> INSPECTION END
M/T MODELS
1.
CHECK PNP SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect park/neutral position (PNP) switch harness connector.
3. Check harness continuity between PNP switch terminal 2 and ground.
Refer to Wiring Diagram.
4. Also check harness for short to power.
OK or NG
OK
>> GO TO 3
NG
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F14, E5
• Harness for open or short between PNP switch and ground
Continuity should exist.
Continuity should exist.
Continuity should exist.
EC-836
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE FOR USA AND CANADA]
P0850 PNP SWITCH
>> Repair open circuit or short to power in harness or connectors.
3.
CHECK PNP SWITCH INPUT SIGNAL CIRCUIT
1. Disconnect ECM harness connector.
2. Check harness continuity between ECM terminal 117 and PNP switch terminal 1.
Refer to Wiring Diagram.
3. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E5, F14
• Harness for open or short between PNP switch and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK PNP SWITCH
OK or NG
OK
>> GO TO 6.
NG
>> Replace PNP switch. Refer to
6.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
Continuity should exist.
P1148, P1168 CLOSED LOOP CONTROL
EC-837
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE FOR USA AND CANADA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1148, P1168 CLOSED LOOP CONTROL
On Board Diagnosis Logic
INFOID:0000000009481516
These self-diagnoses have the one trip detection logic.
DTC P1148 or P1168 is displayed with another DTC for air fuel ratio (A/F) sensor 1.
Perform the trouble diagnosis for the corresponding DTC.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1148
1148
(Bank 1)
Closed loop control
function
The closed loop control function for bank 1 does
not operate even when vehicle is being driven
in the specified condition.
• Harness or connectors
[The air fuel ratio (A/F) sensor 1 circuit is
open or shorted.]
• Air fuel ratio (A/F) sensor 1
• Air fuel ratio (A/F) sensor 1 heater
P1168
1168
(Bank 2)
The closed loop control function for bank 2 does
not operate even when vehicle is being driven
in the specified condition.
EC-838
< DTC/CIRCUIT DIAGNOSIS >
[VQ40DE FOR USA AND CANADA]
P1212 TCS COMMUNICATION LINE
P1212 TCS COMMUNICATION LINE
Description
INFOID:0000000009481517
NOTE:
• If DTC P1212 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
• If DTC P1212 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer
EC-829, "On Board Diagnosis Logic"
.
This CAN communication line is used to control the smooth engine operation during the TCS operation. Pulse
signals are exchanged between ECM and “ABS actuator and electric unit (control unit)”.
Be sure to erase the malfunction information such as DTC not only for “ABS actuator and electric unit
(control unit)” but also for ECM after TCS related repair.
On Board Diagnosis Logic
INFOID:0000000009481518
Freeze frame data is not stored in the ECM for this self-diagnosis. The MIL will not illuminate for this
self-diagnosis.
DTC Confirmation Procedure
INFOID:0000000009481519
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5V at idle.
1. Start engine and let it idle for at least 10 seconds.
2. Check 1st trip DTC.
3. If 1st trip DTC is detected, go to
Diagnosis Procedure
INFOID:0000000009481520
Go to
(TYPE 1) or
(TYPE 2).
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1212
1212
TCS communication line
ECM cannot receive the information from
“ABS actuator and electric unit (control
unit)”.
• Harness or connectors
(The CAN communication line is open or short-
ed.)
• ABS actuator and electric unit (control unit)
• Dead (Weak) battery
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст