Nissan Frontier. Manual — part 390
HOW TO SET SRT CODE
EC-131
< BASIC INSPECTION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
NOTE:
Permanent DTC cannot be checked with a tool other than CONSULT or GST.
With CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
With GST
Select Service $0A with GST.
Is permanent DTC(s) detected?
YES
>> Proceed to
.
NO
>> END
EC-132
< BASIC INSPECTION >
[QR25DE]
HOW TO ERASE PERMANENT DTC
HOW TO ERASE PERMANENT DTC
Description
INFOID:0000000009480765
OUTLINE
When a DTC is stored in ECM
When a DTC is stored in ECM and MIL is ON, a permanent DTC is erased with MIL shutoff if the same mal-
function is not detected after performing the driving pattern for MIL shutoff three times in a raw.
When a DTC is not stored in ECM
The erasing method depends on a permanent DTC stored in ECM. Refer to the following table.
×: Applicable —: Not applicable
*: For group, refer to
.
PERMANENT DTC ITEM
For permanent DTC items, MIL turns ON. Refer to
.
*1: When the same malfunction is de-
tected in two consecutive trips, MIL
will illuminate.
*2: MIL will turn off after vehicle is driven
3 times (driving pattern B) without
any malfunctions.
JSBIA0063GB
Group
*
Perform “DTC CONFIRMATION PROCE-
DURE” for applicable DTCs.
Driving pattern
Reference
B
D
A
×
—
—
B
—
×
×
HOW TO ERASE PERMANENT DTC
EC-133
< BASIC INSPECTION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
PERMANENT DTC SERVICE PROCEDURE
Work Procedure (Group A)
INFOID:0000000009480766
JSBIA0401GB
JSBIA0064GB
EC-134
< BASIC INSPECTION >
[QR25DE]
HOW TO ERASE PERMANENT DTC
1.
CHECK DTC
Check DTC.
Is any DTC detected?
YES
>> Repair malfunction(s) and erase DTC.
• With CONSULT:
.
EC-55, "On Board Diagnosis Function"
NO
>> GO TO 2.
2.
CHECK PERMANENT DTC
With CONSULT
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select “PERMANENT DTC STATUS” mode with CONSULT.
With GST
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select Service $0A with GST.
Is any permanent DTC detected?
YES
>> GO TO 3.
NO
>> END
3.
PERFORM DTC CONFIRMATION PROCEDURE
Perform “DTC CONFIRMATION PROCEDURE” for DTCs which are the same as permanent DTCs stored in
ECM. Refer to
.
>> GO TO 4.
4.
CHECK PERMANENT DTC
With CONSULT
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select “PERMANENT DTC STATUS” mode with CONSULT.
With GST
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select Service $0A with GST.
Is any permanent DTC detected?
YES
>> GO TO 1.
NO
>> END
*1: When the same malfunction is de-
tected in two consecutive trips, MIL
will illuminate.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст