Nissan Frontier. Manual — part 240
DLK-6
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
Is malfunctioning part detected?
YES
>> GO TO 8
NO
>> Check voltage of related BCM terminals using CONSULT.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is displayed, erase it.
>> GO TO 9
9.
FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Is the inspection result normal?
NO (DTC is detected)>>GO TO 7
NO (Symptom remains)>>GO TO 6
YES
>> Inspection End.
INSPECTION AND ADJUSTMENT
DLK-7
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000009478854
Perform the system initialization when replacing BCM, replacing a keyfob or registering an additional keyfob.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000009478855
Refer to the CONSULT Immobilizer mode and follow the on-screen instructions.
DLK-8
< SYSTEM DESCRIPTION >
AUTOMATIC DOOR LOCKS
SYSTEM DESCRIPTION
AUTOMATIC DOOR LOCKS
System Diagram
INFOID:0000000009478856
System Description
INFOID:0000000009478857
DOOR LOCK FUNCTION
• The door lock and unlock switch (driver side) is built into power window main switch.
• The door lock and unlock switch (passenger side) is on door trim.
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors are
unlocked.
Door Key Cylinder
• With the door key inserted in the door key cylinder on driver side, turning it to “LOCK”, will lock door lock
actuator of all doors.
• With the door key inserted in the door key cylinder on driver side, turning it to “UNLOCK” once unlocks the
driver side door lock actuator; turning it to “UNLOCK” again within 5 seconds after the first unlock operation
unlocks all of the other doors. - (SELECTIVE UNLOCK OPERATION)
Selective unlock operation mode can be changed using “DOOR LOCK-UNLOCK SET” mode in “WORK SUP-
PORT”. Refer to
BCS-15, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
AUTOMATIC DOOR LOCKS (LOCK OPERATION)
The interlock door lock function is the function that locks all doors linked with the vehicle speed.
Vehicle Speed Sensing Auto Door Lock*1
All doors are locked when the vehicle speed reaches 24 km/h (15 MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 15 MPH (24 km/h) or more.
ALKIA1722GB
Input
Single
Function
Actuator
Door lock/unlock switch
Door lock/unlock signal
Door lock function
Each door lock actuator
Door key cylinder switch
Each door switch
Door open/close signal
Key reminder function
Combination meter
Warning buzzer signal
Vehicle speed signal
Automatic door lock/unlock
function
TCM
Shift position signal
AUTOMATIC DOOR LOCKS
DLK-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
If a door is opened and closed at any time during one ignition cycle (OFF
→ ON), even after initial auto door
lock has taken place, the BCM will relock all doors when the vehicle speed reaches 15 MPH (24 km/h) or more
again.
Setting change of Automatic Door Locks (LOCK) Function
The lock operation setting of the automatic door locks function can be changed.
With CONSULT
The ON/OFF switching of the automatic door locks (LOCK) function and the type selection of the automatic
door locks (LOCK) function can be performed at the WORK SUPPORT setting of CONSULT. Refer to
"DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Without CONSULT
The automatic door locks (LOCK) function can be switched ON/OFF by performing the following operation.
1. Close all doors (door switch OFF).
2. Turn ignition switch ON.
3. Within 20 seconds of turning the ignition switch ON, press and hold the door lock and unlock switch to the
LOCK position for more than 5 seconds.
4. The switching is completed when the hazard lamps blink.
5. The ignition switch must be turned OFF and ON again between each setting change.
AUTOMATIC DOOR LOCKS (UNLOCK OPERATION)
The automatic door locks (UNLOCK) function is the function that unlocks all doors linked with the key position.
IGN OFF Interlock Door Unlock*1
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.
Setting change of Automatic Door Locks (UNLOCK) Function
The lock operation setting of the automatic door locks function can be changed.
With CONSULT
The ON/OFF switching of the automatic door locks (UNLOCK) function and the type selection of the automatic
door locks (UNLOCK) function can be performed at the WORK SUPPORT setting of CONSULT. Refer to
15, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Without CONSULT
The automatic door locks (UNLOCK) function can be switched ON/OFF by performing the following operation.
1. Close all doors (door switch OFF).
2. Turn ignition switch ON.
3. Within 20 seconds of turning the ignition switch ON, press and hold the door lock and unlock switch to the
UNLOCK position for more than 5 seconds.
4. The switching is completed when the hazard lamps blink.
5. The ignition switch must be turned OFF and ON again between each setting change.
*1: This function is set to ON before delivery.
OFF
→ ON
: 2 blinks
ON
→ OFF
: 1 blink
OFF
→ ON
: 2 blinks
ON
→ OFF
: 1 blink
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст