Nissan Frontier. Manual — part 891
HAC-118
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL A/C (TYPE 1)]
BLOWER MOTOR
1. Turn ignition switch ON.
2. Check voltage between front blower motor relay harness con-
nector E54 terminal 1 and ground.
Is the inspection result normal?
YES
>> Replace variable blower control. Refer to
.
NO
>> Repair front blower motor ground circuit or connector.
9.
REPLACE FUSES
Replace fuses.
Does the fuse blow?
YES
>> • If fuse blows without activating the front blower motor, repair short between fuse and front
blower motor relay.
• If fuse blows activating the front blower motor, GO TO 10.
NO
>> Inspection End.
10.
CHECK FRONT BLOWER MOTOR POWER SUPPLY CIRCUIT FOR SHORT
1. Turn ignition switch OFF.
2. Disconnect front blower motor connector and variable blower
control connector.
3. Check continuity between variable blower control harness con-
nector M121 terminal 4 and ground.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair harness or connector.
11.
CHECK FRONT BLOWER MOTOR
Check front blower motor. Refer to
HAC-119, "Front Blower Motor Component Inspection"
Is the inspection result normal?
YES
>> Replace variable blower control. Refer to
VTL-12, "Removal and Installation"
.
NO
>> Replace front blower motor. Refer to
VTL-11, "Removal and Installation"
12.
CHECK FRONT BLOWER MOTOR
Check front blower motor. Refer to
HAC-115, "Front Blower Motor Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Replace front blower motor. Refer to
HAC-119, "Front Blower Motor Component Inspection"
.
13.
CHECK BLOWER MOTOR GROUND CIRCUIT
1. Disconnect variable blower control harness connector.
2. Check continuity between front blower motor harness connector
M62 (B) terminal 1 and variable blower control harness connec-
tor M121 (A) terminal 2.
Is the inspection result normal?
YES
>> GO TO 14.
NO
>> Repair harness or connector.
14.
CHECK VARIABLE BLOWER CONTROL POWER SUPPLY CIRCUIT FOR OPEN
1 - Ground
: Battery voltage
WJIA1991E
4 - Ground
: Continuity should not exist.
AWIIA0177ZZ
1 - 2
: Continuity should exist.
AWIIA0179ZZ
BLOWER MOTOR
HAC-119
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL A/C (TYPE 1)]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Check continuity between front blower motor relay harness connec-
tor E54 (A) terminals 3, 6 and variable blower control harness con-
nector M121 (B) terminal 4.
Is the inspection result normal?
YES
>> GO TO 15.
NO
>> Repair harness or connector.
15.
CHECK VARIABLE BLOWER CONTROL GROUND CIRCUIT
Check continuity between variable blower control harness connector
M121 terminal 1 and ground.
Is the inspection result normal?
YES
>> GO TO 16.
NO
>> Repair harness or connector.
16.
CHECK VARIABLE BLOWER CONTROL SIGNAL CIRCUIT
1. Reconnect all disconnected component connectors.
2. Disconnect front air control connector.
3. Turn ignition switch ON.
4. Turn blower control dial to maximum speed.
5. check voltage between front air control harness connector M50 terminal 13 and ground.
Is the inspection result normal?
YES
>> Replace front air control. Refer to
VTL-7, "Removal and Installation"
.
NO
>> GO TO 17.
17.
CHECK VARIABLE BLOWER CONTROL SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect variable blower control.
3. Check continuity between front air control harness connector M50 terminal 13 and variable blower control
harness connector M121 terminal 3.
Is the inspection result normal?
YES
>> Replace variable blower control. Refer to
VTL-12, "Removal and Installation"
.
NO
>> Repair harness or connector.
Front Blower Motor Component Inspection
INFOID:0000000009478347
COMPONENT INSPECTION
Front Blower Motor Relay
3, 6 - 4
: Continuity should exist.
AWIIA1212ZZ
1 - Ground
: Continuity should exist.
AWIIA0180ZZ
13 - Ground
Approx.: 4.5V
13 - 3
: Continuity should exist.
HAC-120
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL A/C (TYPE 1)]
BLOWER MOTOR
Check continuity between terminals 3 and 5 and terminals 7 and 6
by supplying 12 volts and ground to coil side terminals 1 and 2 of the
relay.
Front Blower Motor
Confirm smooth rotation of the blower motor.
• Ensure that there are no foreign particles inside the blower unit.
• Apply 12 volts to terminal 2 and ground to terminal 1 and verify that the motor operates freely and quietly.
LJIA0068E
MAGNET CLUTCH
HAC-121
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL A/C (TYPE 1)]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
MAGNET CLUTCH
System Description
INFOID:0000000009478348
SYSTEM DESCRIPTION
The front air control controls compressor operation based on intake temperature and a signal from ECM.
Low Temperature Protection Control
The front air control will turn the compressor ON or OFF as determined by a signal detected by the intake sen-
sor.
When intake air temperature is higher than 3.5
°C (38.3°F), the compressor turns ON. The compressor turns
OFF when intake air temperature is lower than 2.5
°C (36.5°F).
Magnet Clutch Component Function Check
INFOID:0000000009478349
SYMPTOM: Magnet clutch does not engage.
INSPECTION FLOW
1.
CONFIRM SYMPTOM BY PERFORMING OPERATIONAL CHECK - MAGNET CLUTCH
1. Rotate blower control dial clockwise.
2. Press the vent (
) mode switch.
3. Press A/C switch. Confirm that the compressor clutch engages (sound or visual inspection).
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Go to diagnosis procedure. Refer to
HAC-121, "Magnet Clutch Diagnosis Procedure"
.
Magnet Clutch Diagnosis Procedure
INFOID:0000000009478350
Regarding Wiring Diagram information, refer to
HAC-133, "Wiring Diagram - With Type 1"
.
DIAGNOSTIC PROCEDURE FOR MAGNET CLUTCH
SYMPTOM: Magnet clutch does not engage when A/C switch is ON.
1.
PERFORM IPDM E/R AUTO ACTIVE TEST
Perform IPDM E/R auto active test. Refer to
PCS-11, "CONSULT Function (IPDM E/R)"
Does magnet clutch operate?
YES
>> •
WITH CONSULT
GO TO 2.
•
WITHOUT CONSULT
AWIIA1785GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст