Nissan Frontier. Manual — part 128

BRC-40

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C1105, C1106, C1107, C1108 WHEEL SENSOR

C1105, C1106, C1107, C1108 WHEEL SENSOR

Description

INFOID:0000000009479259

When the sensor rotor rotates, the magnetic field changes. It converts the magnetic field changes to current

signals (rectangular wave) and transmits them to the ABS actuator and electric unit (control unit).

DTC Logic

INFOID:0000000009479260

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF DIAGNOSTIC RESULT

With CONSULT.

1. Start engine and drive vehicle at approximately 21 km/h (13 MPH) or more for approximately 5 minutes.

2. Perform self diagnostic result.
Is DTC C1105, C1106, C1107 or C1108 detected?

YES

>> Proceed to diagnosis procedure. Refer to

BRC-40, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009479261

Regarding Wiring Diagram information, refer to

BRC-92, "Wiring Diagram - VDC WITHOUT HILL DESCENT

CONTROL/HILL START ASSIST"

.

CAUTION:

Do not check between wheel sensor terminals.

1.

CONFIRM DTC

With CONSULT

1. Perform self-diagnostic result of ABS and record all active DTCs.

2. Clear all DTCs.

3. Perform DTC confirmation procedure. Refer to

BRC-40, "DTC Logic"

.

Does DTC C1105, C1106, C1107 or C1108 reset?

YES

>> GO TO 2.

NO

>> Refer to

GI-42, "Intermittent Incident"

.

2.

CHECK TIRE PRESSURE AND TIRE WEAR

Check tires for excessive wear and proper inflation. Refer to

WT-35, "Wiring Diagram"

.

DTC

Display Item

Malfunction detected condition

Possible causes

C1105

RR RH SENSOR-2

• When distance between rear wheel sensor RH and

rear wheel sensor RH rotor is large.

• When installation of rear wheel sensor RH or rear

wheel sensor RH rotor is not normal.

• Wheel sensor
• ABS actuator and electric unit

(control unit)

• Sensor rotor

C1106

RR LH SENSOR-2

• When distance between rear wheel sensor LH and

rear wheel sensor LH rotor is large.

• When installation of rear wheel sensor LH or rear

wheel sensor LH rotor is not normal.

C1107

FR RH SENSOR-2

• When distance between front wheel sensor RH

and front wheel sensor RH rotor is large.

• When installation of front wheel sensor RH or front

wheel sensor RH rotor is not normal.

C1108

FR LH SENSOR-2

• When distance between front wheel sensor LH and

front wheel sensor LH rotor is large.

• When installation of front wheel sensor LH or front

wheel sensor LH rotor is not normal.

C1105, C1106, C1107, C1108 WHEEL SENSOR

BRC-41

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace as necessary.

3.

CHECK WHEEL SENSOR

Check wheel sensor for the following:

• Proper installation

• Physical damage

• Contamination
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace as necessary.

4.

CHECK SENSOR ROTOR

Check sensor rotor for the following:

• Contamination

• Physical damage (missing teeth, cracks, etc.)

• Foreign material

• Looseness
Is the inspection result normal?

YES

>> Replace the wheel sensor. Refer to

BRC-113, "Removal and Installation"

. Then, GO TO 5.

NO

>> Repair or replace as necessary.

5.

CONFIRM REPAIR

With CONSULT

1. Clear all DTCs.

2. Perform DTC confirmation procedure. Refer to

BRC-40, "DTC Logic"

.

Does DTC C1105, C1106, C1107 or C1108 reset?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to

BRC-115, "Removal and Installa-

tion"

.

NO

>> Inspection End.

Component Inspection

INFOID:0000000009479262

1.

CHECK DATA MONITOR

On “DATA MONITOR”, select “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR”, and “RR RH SEN-

SOR”, and check the vehicle speed.

Is the inspection result normal?

YES

>> Inspection End

NO

>> Go to diagnosis procedure. Refer to

BRC-50, "Diagnosis Procedure"

.

Special Repair Requirement

INFOID:0000000009479263

1.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator

and electric unit (control unit). Refer to

BRC-12, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL

POSITION : Description"

.

>> GO TO 2

Wheel sensor

Vehicle speed (DATA MONITOR)

FR LH SENSOR

Nearly matches the speedometer dis-
play (

±10% or less)

FR RH SENSOR

RR LH SENSOR

RR RH SENSOR

BRC-42

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C1105, C1106, C1107, C1108 WHEEL SENSOR

2.

CALIBRATION OF DECEL G SENSOR

Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).

Refer to

BRC-13, "CALIBRATION OF DECEL G SENSOR : Description"

.

>> END

C1109 POWER AND GROUND SYSTEM

BRC-43

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

C1109 POWER AND GROUND SYSTEM

Description

INFOID:0000000009479264

Supplies electric power to the ABS actuator and electric unit (control unit).

DTC Logic

INFOID:0000000009479265

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAGNOSIS RESULTS

Check the self-diagnosis results.

Is above displayed on the self-diagnosis display?

YES

>> Proceed to diagnosis procedure. Refer to

BRC-43, "Diagnosis Procedure"

.

NO

>> Inspection End

Diagnosis Procedure

INFOID:0000000009479266

Regarding Wiring Diagram information, refer to

BRC-92, "Wiring Diagram - VDC WITHOUT HILL DESCENT

CONTROL/HILL START ASSIST"

.

1.

CONNECTOR INSPECTION

1. Turn ignition switch OFF.

2. Disconnect ABS actuator and electric unit (control unit) connector.

3. Check terminals for deformation, disconnection, looseness, and so on. If any malfunction is found, repair

or replace terminals.

4. Reconnect connectors and then perform the self-diagnosis. Refer to

BRC-29, "CONSULT Function

(ABS)"

.

Is any item indicated on the self-diagnosis display?

YES

>> GO TO 2

NO

>> Poor connection of connector terminals. Repair or replace connector.

2.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY CIRCUIT AND

GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ABS actuator and electric unit (control unit) connector.

3. Check voltage between ABS actuator and electric unit (control unit) connector E127 terminal 8 and

ground.

DTC

Display item

Malfunction detected condition

Possible cause

C1109

BATTERY VOLTAGE
[ABNORMAL]

When the ABS actuator and electric unit (control unit)
power supply voltage is lower than normal.

• Harness or connector
• ABS actuator and electric unit

(control unit)

Self-diagnosis results

BATTERY VOLTAGE [ABNORMAL]

ABS actuator and elec-

tric unit (control unit)

—

Condition

Voltage

Connector

Terminal

E127

8

Ground

Ignition switch: ON

Battery voltage

Ignition switch: OFF

Approx. 0V